Operation Manual
Table Of Contents
- Table of Contents
- The Sequencer
- Routing Audio and CV
- Remote - Playing and controlling Reason devices
- Using Reason as a ReWire Slave
- Advanced MIDI - the External Control Bus inputs
- Synchronization
- Optimizing Performance
- Transport Panel
- Reason Hardware Interface
- The Combinator
- The Mixer
- The Line Mixer 6:2
- Redrum
- Subtractor Synthesizer
- Malström Synthesizer
- NN-19 Sampler
- NN-XT Sampler
- Introduction
- Panel Overview
- Loading Complete Patches and REX Files
- Using the Main Panel
- Overview of the Remote Editor panel
- About Samples and Zones
- Selections and Edit Focus
- Adjusting Parameters
- Managing Zones and Samples
- Working with Grouping
- Working with Key Ranges
- Setting Root Notes and Tuning
- Using Automap
- Layered, Crossfaded and Velocity Switched Sounds
- Using Alternate
- Sample Parameters
- Group Parameters
- Synth parameters
- Connections
- Dr. Rex Loop Player
- Matrix Pattern Sequencer
- ReBirth Input Machine
- BV512 Vocoder
- The Effect Devices
- Common Device Features
- The MClass effects
- The MClass Equalizer
- The MClass Stereo Imager
- The MClass Compressor
- The MClass Maximizer
- Scream 4 Sound Destruction Unit
- RV7000 Advanced Reverb
- RV-7 Digital Reverb
- DDL-1 Digital Delay Line
- D-11 Foldback Distortion
- ECF-42 Envelope Controlled Filter
- CF-101 Chorus/Flanger
- PH-90 Phaser
- UN-16 Unison
- COMP-01 Auto Make-up Gain Compressor
- PEQ-2 Two Band Parametric EQ
- Spider Audio Merger & Splitter
- Spider CV Merger & Splitter
- Menu and Dialog Reference
- About Audio on Computers
- MIDI Implementation
- Index
TRANSPORT PANEL
70
Overview
The transport panel has standard controls for the sequencer transport, but also features controls for setting tempo, metronome click, locator points etc. The main controls in
the central area of the transport panel are as follows:
Main Transport Controls
The main transport controls function just like standard controls on tape recorders etc. There are also fixed computer keyboard combinations for the most important transport
functions:
You can also use the following transport related key commands:
|Function |Key command |Comments
Stop [0] on the numeric keypad or [Return] Pressing Stop during playback stops the sequencer. Pressing stop again, sets the position to the left lo-
cator (if this is located before the current position). Pressing stop a third time sets the position to the start
of Bar 1. The Stop button also sends out a “Reset” message, in case of stuck notes or other related prob-
lems.
Play [Enter] on the numeric keypad Starts playback of the sequencer.
Rewind [7] on the numeric keypad Clicking once moves the position backward one Bar. If you press and hold this button on the transport
(not using key command) it will start scrolling faster after about 2 seconds.
Fast Forward [8] on the numeric keypad Clicking once moves the position forward one Bar. If you press and hold this button on the transport (not
using key command) it will start scrolling faster after about 2 seconds.
Record [*] on the numeric keypad, or
[Command]/[Ctrl]-[Return]
Activates “Record ready” mode if sequencer is stopped. If activated during playback it will start recording
immediately (“punch in”).
|Function |Key command |Comments
Toggle Stop/Play Space bar Switches between stop and play mode.
Go to Left Locator (Loop Start) [1] on the numeric keypad Sets the position to the left locator.
Go to Right Locator (Loop End) [2] on the numeric keypad Sets the position to the right locator.
Stop
Play
Rewind
Fast Forward
Song Position
Overdub/Replace switch
Loop on/off
Left and Right Locator positions
Record
Time Signature
Tempo