9 Station Swing Set User Manual For model: P9-SS Assembly, Installation, Care, Maintenance, and User Instructions WARNING READ THESE MATERIALS PRIOR TO ASSEMBLING AND USING THIS SWING SET. Failure to assemble and use this swing set as specified in this manual will automatically void the warranty.
Do Not return this product to the store. Instead, please visit our website at www.PropelTrampolines.com where you will find our current contact information. Our friendly customer service staff can help you with any problems or questions that may arise during the assembly, installation, use, maintenance, or obtainment of replacement parts for your Swing Set. This conforms to ASTM F1148, Consumer Safety Performance Specification for Home Playground Equipment.
BEFORE YOU BEGIN Thank you for purchasing a Propel Swing Set. This swing set comes equipped with warnings and instructions for its proper assembly, care, maintenance, and use. This information must be read by all supervisors and users before any person is allowed to use it. Follow all warning pictures included in this manual. If you have any questions regarding these warnings, please contact us.
Operating Instructions Warning 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. Adult supervision is recommended for children of all ages, at all times while the swing set is being used. Do not allow children to walk close to, in front of, behind, or between moving items.
and settle, and should be periodically refilled to maintain at least a 9-inch depth. b. Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.) NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface can result in serious injury to the equipment user.
Parts List (1) Angled Leg Bracket x2 (2) Straight Leg Bracket x1 Has two square crimps (4) Frame Leg Bracket Brace (3) Top Frame Braces Has two punched rectangular holes (5) Top Rail A (6) Top Rail B Has one square crimp (7) Top Rail C (8) Top Rail D (9) Lower Frame Leg Pole x6 (10) Upper Frame Leg x6 (11) Leg Brace for Ladder x1 (12) Leg Brace x2 (13) Slide (14) Slide Rails (15) Slide Bottom A (16) Slide Bottom B (17) Slide Side Rail A (18) Slide Side Rail B (20) Teeter Totter Brace wi
(26) Teeter Totter Bracket x3 (27) Teeter Totter Foot Rest x2 (28) Teeter Totter Seat x2 (29) Teeter Totter Top Bracket x3 (30) Carriage and Glider Rod x4 (31) Carriage and Glider Base x2 (32) Gymnast Bars (33) Swing Seat x2 (34) Carriage Seat Brace x4 (35) Carriage Arm Rest x4 (36) Carriage Seat x4 (38) 5/16” x 2-3/4” Bolt (40) ¼” x 2” Bolt (41 )1/4” X1-1/5”Bolt (43) ¼” x 1-3/8” Carriage Bolt (44) 1/4” x 1-3/4” Carriage Bolt (45) J Bolt (46) 5/16” x 1” Bolt (47) Cap (48) 5/16” X 3/5” Bra
(66) Swing Seat Chains (67) Glider Chains (68) Teeter Totter Seat Supports ASSEMBLY INSTRUCTIONS IMPORTANT ASSEMBLY INFORMATION The following tools are included: Phillips Screwdriver, regular screwdriver, 4mm Allen wrench, 5mm Allen wrench and 10mm / 13mm wrench. Assembly requires two adults. Wear gloves to protect your hands from pinch points during assembly. You should wear clothing and gloves during assembly which will not be damaged or stained by any residue.
Frame Assembly Read and understand all assembly instructions before beginning the assembly process. Step 1- Select Top Rail A (5) and insert the narrow end into Top Rail B (6). Step 2 - Place Angled Leg Bracket (1) on the end of Top Rail A (5) (make sure the leg slots are angled out away from the swing set). Place Straight Leg Bracket (2) on the end of Top Rail B (6).
Step 5 – Bolt on the Angled Leg Brackets (1) and the Straight Leg Bracket (2). Use 5/16” x 2” Bolt (39) with 5/16” Curved washer (55). Use 5/16” Thru Nut (58) with 2/5” Curved Washer (54) to fasten the leg braces to the frame. Repeat this step on the other angled leg brace and the straight leg brace. Step 6 – Attach the Upper Frame Leg (10) to the top frame. Slide a Upper Frame Leg (10) into a Leg Bracket. Align the holes.
Step 7 – Attach the Lower Frame Leg Poles (9) and Leg Braces (11) (12) to the Upper Frame Legs. Start on the side with the Top Rail A (has the two square crimps). Slide the Lower Frame Leg Poles (9) into the upper frame leg. Align the holes. Insert 5/16” x 2” Bolt (39) with a 5/16” Curved washer (55) into the flat part with hole on Leg Brace (11). Install this leg brace to the leg (make sure the leg brace is on the outer part of the frame).
Step 8 – Install End Cap (57). With the Frame assembled insert End Cap (57) into the ends of Top Rail A and Top Rail D (make sure it is pushed in as far as it will go). Accessory Assembly Read and understand all assembly instructions before beginning the assembly process. Step 1 – Attaching the swings. First insert one end of the Swing Seat Chain (66) into the swing seat (33). Fasten it to the seat by using 5/16” Washer (64), 5/16” Nylon Nut (61) and a cap (47).
Step 2 – Attach the Gymnast Bars (32) to Top Rail C (following the directions in Step 1 of attaching the swings). If the handles are not attached to the short chains use the 5/16” Thru Nut (58) to attach them to the chain. Step 3 – Attach the Glider Chains (67) to the Glider Base (31) by first inserting a Carriage and Glider Rod (30) into the glider base holes. Then put the one end of the Y from the chain on the rod and the other end on the same side on the other rod.
Step 4 – Attaching and Assembling the Carriage. First attach the Teeter Totter Brackets (26) to the two square crimps on Top Rail A. Do this by putting Teeter Totter Bracket (26) on the bottom side of the frame, then fasten it on with the Teeter Totter Top Bracket (29), 5/16” x 1” Bolt (46), Teeter Totter Bracket Washer (65) and, the 5/16” Nylon Nut (61).
Insert 2 Brace Spacers (48) into the top of the Carriage Brace Holes. Slide it into the Teeter Totter Bracket and align the holes. Fasten to the Teeter Totter Bracket using 1/4” x 1-3/4” Carriage Bolt (44) and 1/4” Cap Nut (63). Attach the Carriage Arm Rests (35) to the Carriage Seat Braces. Align the Carriage Arm Rests with the squared notch on the inside of the Carriage Seat Braces. Fasten them to the Braces with 1/4”x 11/16” Bolt (62) and 1/4” Washer (59).
Finally attach the Carriage Seat (36) to the Carriage Arm Rests. Use 1/4” x 1-1/5” Bolt (41) and 1/4” Washer (59) to bolt them to the arm rests. Step 5 – Attaching and Assembling the Teeter Totter. First attach the Teeter Totter Bracket (26) to the single square crimp on Top Rail D. Do this by putting Teeter Totter Bracket (26) on the bottom side of the frame, then fasten it on with the Teeter Totter Top Bracket (29), 5/16” x 1” Bolt (46), Teeter Totter Bracket Washer (65) and, the 5/16” Nylon Nut (61).
Insert Teeter Totter Brace Spacer with Plastic Caps (20) into the Teeter Totter Bracket and align the holes. Fasten to the Teeter Totter Bracket using 1/4” x 1-3/4” Carriage Bolt (44) and 1/4”Cap Nut (63). (The Teeter Totter Brace Spacer with Plastic Caps (20) comes in two pieces. Attach the top piece to the longer bottom piece using the 1/4” x 11/16” Bolt (62) and the 1/4” Thru Nut(60).
Insert 2, 5/16” x 1/2" Brace Spacers (52) into the sides of the Teeter Totter Seats Supports (68). Align the brace spacer and Teeter Totter Seat Supports with the holes on the Teeter Totter Brace. Fasten the supports to the brace by inserting the J bolt (45) into the support bar with two holes and then insert the 1/4” Thru Nut (60) thru the other side. Loosely tighten. Attach the Teeter Totter Seat (28) to each end of the support bars.
Finally attach the Teeter Totter Foot Rest (27) to the bottom of the braces. Use the 1/4” x 3/4” Screws (50) to screw them to the braces. Step 6 – Assembling the slide. Put the Slide Bottom B (16) on the right side of the bottom piece (the bottom piece has the rectangular posts and round posts). Slide the upper slide into the groove on the bottom piece, and then put the Slide Rail (14) on it. Then put the Slide Side Rail A (17) on the very top piece. Attach all the side rails with the Slide Plugs (37).
(Flip the side onto its other side and repeat Step 6) Step 6 – Assembling the slide ladder. Take the Ladder Braces (19) and attach the Ladder Steps (24) to them. Attach them with the 1/4”x 11/16” Bolt (62), 1/4” Washer (59), and the ¼” Cap Nut (63).
Attach the Ladder Legs (21) to the ladder braces by inserting them into the ladder brace and then attaching them with 1/4”x 11/16” Bolt (62) and the 1/4” Thru Nut (60). Attach the ladder to the main frame by lining up the holes on the Ladder Brace with the holes on the Leg Brace for the ladder that is attached to the swing set legs. Insert the 1/4” x 2-3/4” Bolt (42) into the holes on the frame Leg Brace. Then slide the Ladder Spacer (49) onto the bolts. Then put the ladder brace on the bolts.
Finally attach the slide to the ladder. Slide the Slide Support Bar (22) into the two grooves under the slide. Set the slide and support bars onto the ladder and line up the holes on each side. Fasten the slide to the ladder using the 1/4” x 2” Bolt for Slide Rail (25), 1/4” Washer (59), and 1/4” Cap Nut for the Slide Rail (63). Repeat for both Slide Bars. Your swing set assembly is complete. Make sure that all parts are securely attached.
Swing Set Anchor Kit It is highly recommended that you secure your swing set to prevent tipping. Please follow the instructions below to install the anchoring kit. Step 1- Insert the Anchor (56) into the hole at the bottom of the leg. Step 2- Using a rubber mallet, pound each stake at a 45-degree angle into the ground until it is flush with ground level. This completes the installation of your Anchor Kit.
Use equipment only as intended. Do not use equipment if you are wearing inappropriate items, such as but not limited to, loose fitting clothing, hood and neck drawstrings, scarves, cord-connected items, capes, and ponchos. These items can cause death by strangulation. Do not climb on equipment when it is wet. Check openings between rollers and sliding surfaces of roller slides for foreign materials that could be potentially hazardous to users.
removed for the cold season. f. Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary. 2. Twice a month during play season: a. Tighten all hardware b. Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. c. Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary. 3.
For more information or to order any of these accessories, please visit our website at www.PropelTrampolines.com. MY SWING SET INFORMATION In the event you need to contact customer service, such as to ask questions, order replacement parts, or file a warranty claim, you will be asked to provide some basic information about your swing set. By writing this information in the spaces below and keeping this Manual in an accessible location, you can help expedite this process.
LIMITED WARRANTY PROPEL warrants its swing set products to be free from defects in material and workmanship under normal use and service conditions. The powder coated steel frame are warranted for one (1) year from the date of purchase. All other parts are warranted for ninety (90) days from the date of purchase. All warranty coverage extends only to the original retail purchaser from the original date of purchase.
Warranty Registration Don’t forget to register your Swing Set by visiting www.PropelTrampolines.com/warranty. Registering your Swing Set entitles you to receive all warranty benefits. You may also register your Swing Set by mailing a copy of your sales receipt along with your name, address, phone number and the model number of your trampoline to: Propel Trampolines Warranty Department 41 East 400 North #324 Logan, UT 84321 www.propeltrampolines.com V1.
