High performance Battle drones tie advanced x1 Imperial manual Warning: Never leave Li-poly batteries charging unattended for extended periods of time. Please refer to enclosed safety instructions.
Table of contents 01. Features 02. Pilot’s Gear 03.Vehicle stats 04. Package contents 05. Controller battery installation 06. Ship battery installation 07. Charging your ship’s battery 08. Replacing the propeller blades 09. Turning your controller on 10. Syncing your ship 11. Controller functions 12.Learning how to fly (T-mode) 13.Protective cage 14. Preparing for flight 15. Flight controls 16. Flying tips 17. Recognizing the front and back of your ship 18. Speed select 19.
Features • Built-in 6-axis gyroscope keeps the TIE advanced extremely stable in all conditions • 4-channel flight controls allow for incredible maneuvering including 360o rolls • LED directional lights make your ship easy to follow • Hand-painted to model-quality finish • Running lights illuminate your ship during low-light flying • Barometric pressure sensor (repulsorlift) for fixed altitude hovering • Auto-start and auto-land functions • Gyroscope calibration • Crash protection with auto-land • T-mode tra
ear Pilot’s G Front lights Life LEDs Bluetooth Sync for future app integration Calibrate Gyro Barometric pressure sensor On/Off Battery Handle grip Auto-start / Auto-land Turn On/Off LEDs Battery Lock Speaker Neck Strap Attachment Headphone Jack (Lanyard not included) Controller Power on/off Propeller Battery Cover IR Transmitter (Front of the ship) Phone holder Pull tab Speed Change Weapons Fire Counterclockwise Roll Clockwise Roll IR Receiver Left Gimbal (Control stick) Right Gimbal (
Package contains vehicle stats Training cage Extra accessories Wall charger & Batteries CONTROLLER High performance battle drone Open page - top secret 5 Tie Advanced x1 2.
REMOTE CONTROL BATTERY INSTALLATION use alkaline or 1.5V rechargeable batteries NOTES 1 -Unscrew and slide 2 -4 AA batteries 3 -Put back cover 1. On the back of the controller, unscrew and slide off the battery cover. - There is a screwdriver hidden in the right side arm of the controller. 2. Install 4 AA alkaline batteries (1.5V rechargeable batteries are preferred) into the controller. - Check proper orientation! 3. Replace the battery cover and secure it with screws. 4.
Ship Battery installation 1. During your first installation, pull the clasp to the unlocked position (as shown in illustration) to unlock the battery. Next, remove the battery cover that comes in the package, as this cover is cosmetic and used for display purposes only. 2. Slide the fully-charged battery into the ship’s battery compartment (see diagram). 3. Push down and make sure the battery is fully seated. The ship’s LED lights will illuminate and start flashing when the battery is properly connected. 4.
Note: The charging adapter will show a red indicator light when plugged in, and a blinking red indicator light when charging the battery. CHARGING your Ship’s LI-POLY BATTERY 1. Insert the correct wall socket extension into the wall adapter depending on the country you are in (see illustration A). 2. Next, connect the USB charging cord to the wall adapter and the charger. Steady Red -> Plugged in Charging in progress Blinking Red -> Illustration A 3.
PROPELLER INSTALLATION AND REPLACEMENt A B B A Your Tie Advanced s propeller system is a precision instrument that may need repair or replacement from time to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your propellers. ’ 1. The ship has four propellers, two “A” Propellers, and two “B” Propellers. 2. When replacing the propeller blades, make sure to put A propellers on A Motors, and B Propellers on B motors, as per the diagram at the right. 3.
WARNING! Do not fly your ship in foul weather! 2 second push on/off Important! When syncing your ship with the controller, always check that the ship is on a flat level surface. This ensures that the 6-axis gyro is properly calibrated. Your ship utilizes an automatic 2.4 GHz channel selection system that allows up to 12 people to fly side-by-side in the same wireless range with no interference.
Music mode Music mode lets you adjust the volume on your speaker or headphones or choose a background track. To enter music mode, hold down button 2 and button 4 for two seconds. The Life LEDs will glow blue (or red in simulation mode). Push both buttons again for two seconds to exit music mode. If no buttons are pushed for five seconds while in music mode, the controller will automatically exit the mode.
screwdriver This handy screwdriver attaches to your controller and can be used to remove screws from the battery cover or to tighten the screw on the phone holder. It can also be used to remove parts on your drone if repairs are needed. Speaker The controller’s speaker will play every sound, including music, explosions, and more. headphone Jack The controller’s headphone jack functions in the same way as the speaker, but will only work when the headphones are plugged in.
Barometric Pressure sensor on/off (repulsorlift on/off) The barometric pressure sensor maintains the altitude of your ship above the ground, simulating the anti-gravity effect of a repulsorlift engine. This also lets you adjust your altitude incrementally during flight. Push the gimbal up or down and then release it, and your ship will hover at the new altitude.
Learning how to fly (T-mode) If this is your first time flying please read the following instructions. If you are an experienced pilot feel free to skip ahead to the next section. T-mode is a special flying mode intended to help ease new pilots into learning basic flight controls in a safe environment. To operate in T-mode you must first activate the repulsorlifts on the controller (see repulsorlifts on page 14).
protective cage For beginner pilots we strongly suggest using the protective cage. Make sure you install your protective cage before flight. This cage protects the propeller blades and the outside of the ship from taking damage when crashing into walls and other objects.
For Multi-Person Play Before beginning, ensure that all ships and controllers are powered off. Make sure that no other 2.4GHz devices are in the area. Each person must sync their vehicle individually, one at a time, in order to avoid interference. Follow steps on page 11 (“SYNC TO SHIP: FOR SINGLE-PERSON PLAY”), making sure to keep away from others while ensuring that no one else is syncing at the same time.
FLIGHT CONTROL These are the basic flight functions for your ship. While learning to fly it is best to begin with a large space, at least until you get used to the basics. Once you master your ship you can tackle more advanced maneuvers. Practice makes perfect! Once you have these steps mastered, move to the next level. Move the Throttle up to increase the speed of the motors and the Tie Advanced will rise up. Move the Throttle down to decrease the speed of the motors and the Tie Advanced will descend.
FLYING TIPS Operate your ship in a wide space. Ideally, the space will have at least a 100 foot radius. If you are flying your ship with others, make sure spectators are located behind you. For best performance, it is recommended that you operate the ship during zero wind conditions, as wind can greatly affect flight performance.
Speed change When the controller is start on Speed Mode 1. in Speed Mode 3 before return to Speed Mode 1 Speed 1 Speed 2 powered on, it will always If the controller was turning it off, it will when it is turned back on. Push the button to change speeds between Modes 1-3. If you are in Speed Mode 3 and press the button, you will cycle over to Speed Mode 1. Flying speed is indicated by the LEDs surrounding the controller’s power button.
Auto-start/Auto-land When repulsorlifts are activated, push button once when on the ground to autostart. Push button for 2 seconds when in the air to auto-land. Auto-start Auto-start only works when the barometric pressure sensor is activated. If barometric pressure sensor is activated, auto-start will work only if the left stick (gimbal) is in the center position. The right control stick will function normally during the auto-start sequence, allowing you to control the direction of your take-off.
Clockwise roll (A) Push the right trigger button while flying and your ship will perform a 360-degree roll in a clockwise motion while continuing its current movement. If the ship is flying forward it will continue to move forward as it performs the roll, and will perform similarly with any directional movement. counterclockwise roll (B) Push the left trigger button while flying and your ship will perform a 360-degree roll in a counterclockwise motion while continuing its current trajectory.
battling When battling with your vehicle it is best to fly outside in a wide open space of about 200-300 feet, in an open field with no obstruction such as trees, houses, open water, or power lines. When battling indoors it is recommended to do so in a very large open area such as a gymnasium or sports center with high ceilings and no obstructions.
Life LED’s When the controller’s power is turned on, all 3 life LEDs will flash. Once synced, all 3 life LEDs will glow red. Reactions to being hit: When the ship is hit by an opponent, it will react and alter its flight. No additional hits can be inflicted on the ship during this time. Full life 1st hit 2nd hit 3rd hit FIRST HIT: The ship will continue on its current trajectory, but will rock back and forth two times left to right in a fluid motion.
THIRD HIT AUTO LANDING: This is the final hit in battle. When you have been hit a 3rd time your drone will enter into auto-land mode and descend in a downward spiral. TAKING OVER LANDING SEQUENCE Pulling your left throttle stick all the way down during auto-landing sequence will activate user controlled landing mode. This feature allows you to take control of your direction while you fall. This may be used to avoid hitting an obstacle.
He wont be abl e to fo llow! Named after Adar Tallon, Imperial defector who bravely aided Alliance, the Tallon Roll is a tricky technique that’s executed an enemy pilot is approaching fast from the rear. If the when the pilot levels out and pulls up while rolling away from the direction of the turn, they can slip back in behind the enemy with no loss of distance or speed.
ch wat him ation of a chasing drop beneath the elev your throttle and while nerable underbelly r Tie advanced’s vul enemy.
stay in front of your enemy’s turn he or t ch f rn! r tu unte wat co ea se in sl t ip -g o si ta et de rg on et When you’re in the ri ght spo combina t, use a tion of your yaw (sideways and aile ron strafe) controls in a full to stra circle ar fe ound yo If you tim ur oppo nent. e it rig h t, you ca tate Reb n devasel attack ers.
ya de w 180 gr tu ee rn prey tu rns ac att to w y l elo bel p b y’s dro nem e r you predat or k ering by mast n game eir ow h ll t fu t a t turn a pilots 180 Degree Beat rebel nal make a irectio . d ve d o m pi a r en this ng in a can th i u lt u yo es . arc le, r rning k.
No Say yo no to memory- wiped ur bel te ct ly Astromechs Get qu se ro ! P up ick on ! hi s t ail ing hop, your rear, execute a jump a rebel is closing in from forward your ng losi off on your throttle, by pulling up and easing you’ll find , t righ it do you f I behind them. speed and dropping back .
tie advanced WARNING Your TIE Advanced is designed for INDOOR or OUTDOOR use. The TIE Advanced blades revolve at high speeds and can cause harm to the user, spectators, and animals. Stand clear of the ship to reduce the risk of getting into its flight path. Warn spectators that you will be flying your ship so that they can remain aware of its position. Before flying, inspect the ship’s rotor blades to ensure they are securely fastened. WARNING! Choking/Cutting Hazard: Small parts/sharp rotor blades.
BATTERY WARNINGS This ship uses a Li-poly rechargeable battery. If the battery no longer stays charged, dispose of it properly according to local disposal requirements. Controller requires 4“AA batteries (not included). Please read the important battery safety warning below. Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride). Do not mix old and new batteries. Non-rechargeable batteries are not to be recharged.
FCC Part 15 C Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Propel UK Returns Policy At Propel, we make premium products using the very best components. There are, on occasions, reasons for customers to return products to us. Propel UK offers a 90-day warranty to cover these eventualities, the details of which can be found on the Propel UK website at propelrc.co.uk. In the event of this being for the return. The details and conditions please visit find our Returns Policy and necessary you are required to choose the correct reason as to what is required are below.
Propel UK Returns Policy Returned Items FailinG Within the Warranty Period If a fault occurs within the first 90 days from the date of purchase (and the fault is covered under the manufacturer's guarantee) then you will need to go to propelrc.co.uk and select the "customer care" link and request a Return Merchandise Authorization Form or "RMA". You will need to ship the product to our address (see above) with a copy of the completed RMA form inside the box.
Propel UK Returns Policy Items Damaged during Transit In the event that you purchased online, and later signed for, an item that has clearly been damaged in transport, you should add a comment to your signature for the items with the courier. You must also still inform us within the 7-working-day period if you have accepted goods which were clearly damaged when you received them by completing the Returns Authorisation Form with all the required information.
Limited 90-Day Warranty North America ROOFTOP BRANDSTM warrants to the original consumer that this product is free from any electrical or mechanical defects for a period of 90 DAYS from the date of purchase. If any such defect is discovered within the warranty period, ROOFTOP BRANDSTM will repair or replace the unit free of charge upon receipt of the unit, Shipped postage prepaid and insured to our warranty center.
industry canada notice canada only This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
PILOT’s LOG 39
