User manual
Table Of Contents
- SuperTrak User Manual
- Contents
- Chapter 1: Introduction
- Chapter 2: Installation
- Unpacking the SuperTrak Card
- Installing the SuperTrak Card
- Choosing the Physical Drives
- Creating a Logical Drive
- Installing the CLI
- Installing WebPAM PRO
- Logging into WebPAM PRO
- Setting up WebPAM PRO
- Chapter 3: Installing Drivers
- Chapter 4: SuperBuild™ Utility
- Chapter 5: Management with WebPAM PRO
- Logging into WebPAM PRO
- Accessing the Interface
- Managing Users
- Working with Subsystem/Host Management
- Managing Software Services
- Managing the Host
- Managing the Subsystem
- Viewing Subsystem Information
- Clearing Statistical Data
- Setting an Alias for the Subsystem
- Updating the Firmware
- Checking Subsystem Health
- Viewing the Runtime Event Log
- Saving the Runtime Event Log
- Clearing the Runtime Event Log
- Viewing the NVRAM Event Log
- Saving the NVRAM Event Log
- Clearing the NVRAM Event Log
- Viewing Current Background Activities
- Making Background Activity Settings
- Running Background Activities
- Running Media Patrol
- Running PDM
- Viewing Scheduled Activities
- Scheduling an Activity
- Deleting a Scheduled Activity
- Viewing System Configuration
- Managing the Controller
- Managing Enclosures
- Managing Physical Drives
- Viewing a List of Physical Drives
- Locating a Physical Drive
- Making Global Physical Drive Settings
- Viewing Physical Drive Information
- Viewing Physical Drive Statistics
- Making Physical Drive Settings
- Clearing Stale and PFA Conditions
- Viewing the SMART Log
- Viewing Advanced SMART Log Information
- Saving Advanced SMART Log Information
- Making SMART Log Settings
- Managing Disk Arrays
- Viewing Disk Arrays
- Locating a Disk Array
- Creating a Disk Array
- Creating a Disk Array - Automatic Configuration
- Creating a Disk Array - Express Configuration
- Creating a Disk Array - Advanced Configuration
- Deleting a Disk Array
- Viewing Disk Array Information
- Making Disk Array Settings
- Creating a Logical Drive
- Deleting a Logical Drive
- Migrating a Disk Array
- Rebuilding a Disk Array
- Running Media Patrol on a Disk Array
- Running PDM on a Disk Array
- Transitioning a Disk Array
- Preparing a Disk Array for Transport
- Managing Logical Drives
- Managing Spare Drives
- Working with the Logical Drive Summary
- Chapter 6: Management with the CLI
- Opening the CLI on Windows
- Opening the CLI on Linux, FreeBSD, and VMware
- Table of Supported Commands
- Notes and Conventions
- List of Supported Commands
- Chapter 7: Technology Background
- Chapter 8: Troubleshooting
- Chapter 9: Support
- Appendix A: Partition and Format
- Appendix B: Upgrades
- Appendix C: Battery Backup Unit
- Appendix D: LED Backplane Connections
- Index
Chapter 9: Support
275
I already have an array on a Promise FastTrak controller. Can I move that
array to my new SuperTrak EX Series controller?
No. The SuperTrak EX Series controller supports SNIA Disk Data Format
(DDF), which is not backward compatible with the FastTrak controller.
If I have a problem with one of the drives on the SuperTrak EX Series, how
can I low-level format it to correct the problem?
Do NOT do this! Low-level formatting hard physical drives is not only
unnecessary but it generally does not correct problems commonly
experienced during use.
Errors such as bad sectors or ECC/CRC failure are best remedied by
completely replacing the drive. For this reason, do NOT low-level format the
drives attached to the SuperTrak EX Series controller.
Do I have to install disk management software on my logical drive in order
to access the full storage capacity of drives?
No! Disk management software will only complicate things. The logical drive
should be fully addressable by your OS as it is. Some operating systems
have limits on the sizes of partitions and logical drives that can be defined.
Consult your OS documentation about partitioning larger drives.
What system BIOS setup settings do I use for the drives on the SuperTrak
EX Series?
A BIOS setting is required only if you want to boot your system from the
logical drive on the SuperTrak EX Series controller. After your logical drive is
created, partitioned and formatted, make the change in your BIOS boot
order setting.
How do I partition/format my SuperTrak EX Series RAID logical drive?
The SuperTrak EX Series controller represents the logical drive as a single
physical drive to your system. Therefore, anything that you can do to a single
physical drive you can do to a SuperTrak logical drive.
For example, you should use the FDISK and FORMAT utilities to partition
and format the logical drive. You can format the logical drive with any file
system you wish.
Installation Issues (Capacity, Booting)
How can I change the system boot sequence in order to boot from the
SuperTrak EX Series logical drive?
The boot sequence is controlled by the system BIOS. As far as the system
BIOS is concerned, the SuperTrak EX Controller and defined logical drives