User manual
Table Of Contents
- SuperTrak User Manual
- Contents
- Chapter 1: Introduction
- Chapter 2: Installation
- Unpacking the SuperTrak Card
- Installing the SuperTrak Card
- Choosing the Physical Drives
- Creating a Logical Drive
- Installing the CLI
- Installing WebPAM PRO
- Logging into WebPAM PRO
- Setting up WebPAM PRO
- Chapter 3: Installing Drivers
- Chapter 4: SuperBuild™ Utility
- Chapter 5: Management with WebPAM PRO
- Logging into WebPAM PRO
- Accessing the Interface
- Managing Users
- Working with Subsystem/Host Management
- Managing Software Services
- Managing the Host
- Managing the Subsystem
- Viewing Subsystem Information
- Clearing Statistical Data
- Setting an Alias for the Subsystem
- Updating the Firmware
- Checking Subsystem Health
- Viewing the Runtime Event Log
- Saving the Runtime Event Log
- Clearing the Runtime Event Log
- Viewing the NVRAM Event Log
- Saving the NVRAM Event Log
- Clearing the NVRAM Event Log
- Viewing Current Background Activities
- Making Background Activity Settings
- Running Background Activities
- Running Media Patrol
- Running PDM
- Viewing Scheduled Activities
- Scheduling an Activity
- Deleting a Scheduled Activity
- Viewing System Configuration
- Managing the Controller
- Managing Enclosures
- Managing Physical Drives
- Viewing a List of Physical Drives
- Locating a Physical Drive
- Making Global Physical Drive Settings
- Viewing Physical Drive Information
- Viewing Physical Drive Statistics
- Making Physical Drive Settings
- Clearing Stale and PFA Conditions
- Viewing the SMART Log
- Viewing Advanced SMART Log Information
- Saving Advanced SMART Log Information
- Making SMART Log Settings
- Managing Disk Arrays
- Viewing Disk Arrays
- Locating a Disk Array
- Creating a Disk Array
- Creating a Disk Array - Automatic Configuration
- Creating a Disk Array - Express Configuration
- Creating a Disk Array - Advanced Configuration
- Deleting a Disk Array
- Viewing Disk Array Information
- Making Disk Array Settings
- Creating a Logical Drive
- Deleting a Logical Drive
- Migrating a Disk Array
- Rebuilding a Disk Array
- Running Media Patrol on a Disk Array
- Running PDM on a Disk Array
- Transitioning a Disk Array
- Preparing a Disk Array for Transport
- Managing Logical Drives
- Managing Spare Drives
- Working with the Logical Drive Summary
- Chapter 6: Management with the CLI
- Opening the CLI on Windows
- Opening the CLI on Linux, FreeBSD, and VMware
- Table of Supported Commands
- Notes and Conventions
- List of Supported Commands
- Chapter 7: Technology Background
- Chapter 8: Troubleshooting
- Chapter 9: Support
- Appendix A: Partition and Format
- Appendix B: Upgrades
- Appendix C: Battery Backup Unit
- Appendix D: LED Backplane Connections
- Index
SuperTrak EX Series User Manual
274
How can I change the resources that the SuperTrak uses?
The SuperTrak EX Series Controllers are fully PnP. This means all the
resources that it uses are given to it by the PnP BIOS on the motherboard.
The SuperTrak Series Controller supports IRQ sharing, but this feature only
works when ALL the concerned devices support it. If your motherboard
allows you to control the assignment of these resources, you may be able to
remedy the problem by:
• Changing the IRQ assignments to the PCI slots in the motherboard
BIOS during boot up.
• Reset the configuration data in your CMOS. This is usually an option in
the PnP section of your CMOS.
• Otherwise, switch the SuperTrak Controller card to a different PCI slot.
Drive Issues
Can I add a drive to a SuperTrak EX Series logical drive via hot-swap and
dynamically adjust the array size/configuration?
Yes. The SuperTrak EX Series controller supports online logical drive
expansion and migration. You must use the SuperBuild utility or the
WebPAM PRO software to expand or migrate an existing logical drive.
Do the HDDs on the SuperTrak EX Series have to be the same size?
The physical drives that you use with the SuperTrak EX Series controller do
not have to be the same size. If the sizes differ, the SuperTrak EX Controller
will truncate the large drive so the capacities match. The resulting difference
in drive space is unusable, so avoid using physical drives of significantly
different capacities.
Can I take a drive used in a SuperTrak EX Series logical drive and access it
directly with a different controller, such as the one integrated on the
motherboard?
Yes, but only under certain configurations. First, the other controller must
address the drives as LBA, not CHS.
Second, only the following configurations allow the drive(s) to be accessed
individually on another controller:
• Single-drive RAID 0 (stripe)
• One drive from a RAID 1 (mirror) logical drive
No other array configurations will work for this purpose.