User manual
Table Of Contents
- SuperTrak User Manual
- Contents
- Chapter 1: Introduction
- Chapter 2: Installation
- Unpacking the SuperTrak Card
- Installing the SuperTrak Card
- Choosing the Physical Drives
- Creating a Logical Drive
- Installing the CLI
- Installing WebPAM PRO
- Logging into WebPAM PRO
- Setting up WebPAM PRO
- Chapter 3: Installing Drivers
- Chapter 4: SuperBuild™ Utility
- Chapter 5: Management with WebPAM PRO
- Logging into WebPAM PRO
- Accessing the Interface
- Managing Users
- Working with Subsystem/Host Management
- Managing Software Services
- Managing the Host
- Managing the Subsystem
- Viewing Subsystem Information
- Clearing Statistical Data
- Setting an Alias for the Subsystem
- Updating the Firmware
- Checking Subsystem Health
- Viewing the Runtime Event Log
- Saving the Runtime Event Log
- Clearing the Runtime Event Log
- Viewing the NVRAM Event Log
- Saving the NVRAM Event Log
- Clearing the NVRAM Event Log
- Viewing Current Background Activities
- Making Background Activity Settings
- Running Background Activities
- Running Media Patrol
- Running PDM
- Viewing Scheduled Activities
- Scheduling an Activity
- Deleting a Scheduled Activity
- Viewing System Configuration
- Managing the Controller
- Managing Enclosures
- Managing Physical Drives
- Viewing a List of Physical Drives
- Locating a Physical Drive
- Making Global Physical Drive Settings
- Viewing Physical Drive Information
- Viewing Physical Drive Statistics
- Making Physical Drive Settings
- Clearing Stale and PFA Conditions
- Viewing the SMART Log
- Viewing Advanced SMART Log Information
- Saving Advanced SMART Log Information
- Making SMART Log Settings
- Managing Disk Arrays
- Viewing Disk Arrays
- Locating a Disk Array
- Creating a Disk Array
- Creating a Disk Array - Automatic Configuration
- Creating a Disk Array - Express Configuration
- Creating a Disk Array - Advanced Configuration
- Deleting a Disk Array
- Viewing Disk Array Information
- Making Disk Array Settings
- Creating a Logical Drive
- Deleting a Logical Drive
- Migrating a Disk Array
- Rebuilding a Disk Array
- Running Media Patrol on a Disk Array
- Running PDM on a Disk Array
- Transitioning a Disk Array
- Preparing a Disk Array for Transport
- Managing Logical Drives
- Managing Spare Drives
- Working with the Logical Drive Summary
- Chapter 6: Management with the CLI
- Opening the CLI on Windows
- Opening the CLI on Linux, FreeBSD, and VMware
- Table of Supported Commands
- Notes and Conventions
- List of Supported Commands
- Chapter 7: Technology Background
- Chapter 8: Troubleshooting
- Chapter 9: Support
- Appendix A: Partition and Format
- Appendix B: Upgrades
- Appendix C: Battery Backup Unit
- Appendix D: LED Backplane Connections
- Index
SuperTrak EX Series User Manual
192
You can accept the array in incomplete condition and try
to bring the logical drives online. However, that is a high-
risk and non-revertible operation, and it may result in data
loss. Therefore, it is recommended to clear the condition
first, for example: putting the missing drives back or
roaming the array back to the original controller and wait
until the migration completes.
transport Takes the array and the logical drives on the array offline
to get ready for transport the array to another subsystem.
-d <DA ID> The disk array ID. Valid values are 0-255. Specifies the
desired array ID when creating (add) an array. Specifies
the array ID when listing array information, modifying,
deleting, locating, accepting, adding or deleting a logical
drive. Only one array may be specified.
-p <PD ID list> Specifies physical drives to be used in an array, with -a
add option. PD IDs are specified individually or separated
by comma. Sequential group of physical drives are
specified by placing a ~ between numbers such as 1~6.
This will include physical drives 1, 2, 3, 4, 5, and 6.
-s "<option>=<value> Specifies array settings when creating (add) or modifying
(mod) an array. Options are comma separated.
alias= A user-specified array name. Up to 32 characters, alpha-
numeric characters, blank spaces and underscores.
Beginning and ending blank spaces are discarded.
mediapatrol= Enables or disables Media Patrol for this array.
enable The default is enable.
disable
pdm= Enables or disables PDM for this array.
enable The default is enable.
disable
-l "<option>=<value>" Specifies logical drive settings when adding a logical
drive to an existing array (addld) or during array creation
(add). Options are comma separated.
<LD ID list> Specifies a list of Logical Drive IDs. Requires the -a delld
option.
ID= Assigns a specific ID to an array. Overrides automatic ID
assignment. Valid values are 0-255.
Alias= A user-specified name for the logical drive.
Raid= Specifies logical drive RAID level.
0 Striping.