Owner's Manual
Black (hot/power)
White (neutral)
Bare/Green
(ground)
White
Black
Black
Black
White
Blue
Blue
White
Green
Green
Receiver
1. Use existing pull chains on the desired
fan to set fan speed to HIGH and to turn
the light ON.
2. Turn o circuit breakers and wall
switch to the fan.
DANGER: Failure
to disconnect power supply prior to
installation may result in serious injury
or death.
3. Lower the canopy of the previously
assembled fan and insert receiver into
the mounting bracket with antenna end
rst and the at side facing the ceiling.
Note: If installing this product with
a new fan, insert the receiver in the
mounting bracket before wiring the
fan; wire the fan according to these
instructions, then continue fan assembly
as directed in the fan’s instruction
manual.
UNIVERSAL
WALL REMOTE
Model #51487, 51433
4. Disconnect existing wire connections
(if applicable), then secure all wire
connections with wire connectors
according to diagram and these steps:
• Connect the green wires from the downrod
and mounting bracket to the bare/green
(ground) supply wire.
• Connect the Blue wire (FOR LIGHT) from
the receiver to the Blue fan wire.
• Connect the Black wire (TO MOTOR L) from
the receiver to the Black fan wire.
• Connect the White wire (TO MOTOR N)
from the receiver to the White fan wire.
• Connect the Black wire (AC IN L) from
the receiver to the Black (hot/power)
supply wire.
• Connect the White (AC IN N) from the
receiver to the White (neutral) supply wire.
Fan Pull
Chain
Light Pull
Chain
Canopy
Receiver
Wall
Bracket
Mounting
Screw
Wire Connector
5. Wrap electrical tape (not included)
around each wire connector down to
the wire. Then, push wire connections
into the outlet box. Place the White wire
connections on the opposite side of the
outlet box from the Black and Blue wire
connections.
6. Reinstall the canopy.
7. Turn on power supply and wall switch
to the fan.
8. Remove the battery door from the
back of the remote using a at-head
screwdriver (not included). Insert the
two CR2032 batteries into the remote;
ensure the positive pole of the batteries
face up (as pictured) and then replace
the battery door. Press the HIGH SPEED
button to ensure the LED indicator
illuminates and the fan turns on.
9. If desired, the wall bracket can be
attached to a wall using the mounting
screws.
Questions? Call our customer service department at
1-877-706-3267, 8 a.m. - 5 p.m. Central Time, Monday-Friday.
Remote
Qty. 1
Wall Bracket
Qty. 1
Battery
Qty. 2
Receiver
Qty. 1
Wire Connector
Qty. 5
Mounting Screw
Qty. 2
Owner’s Manual
Qty. 1
Read instructions completely before installing the remote.
WARNING: If the color of the household supply wires is different than what is referred to in the instructions below, a professional electrician should determine proper wiring.
CAUTION:
• Do not install in damp locations. For indoor use only.
• Do not use with fans that have integrated remote controls.
• Do not use with hugger-style fans.
• Be sure the outlet box is properly grounded or that a green or bare (ground) wire is present.
• This unit is intended to control a ceiling fan with electrical source of AC 110/120V, 60Hz.
• To reduce the risk of re or electric shock, do NOT use a full-range dimmer switch to control the fan speed.
• CAN ICES-005 (B)/NMB-005 (B)
• This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help. Any changes or modications not expressly approved by the grantee of this device could void the user’s authority to
operate the equipment.
HKC-US, 3350 Players Club Pkwy. #225, Memphis, TN 38125
(877) 706-3267
Owner’s
Manual
SAFETY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
1 5
2 6
3 7
4
8
9
Canopy