PACKAGE CONTENTS 1 Unpack your fan and check the contents. You should have the following items: 2 3 4 5 19 7 6 8 9 11 15 18 10 12 PACKAGE CONTENTS 12. Switch Housing 1. Canopy 22 17 2. Canopy Cover 13. Switch Housing Screw (x3) 3. Mounting Bracket Screw (x4) 14. Switch Housing Cap 4. Mounting Bracket 16. Light Cage (x3) 5. Downrod 17. Blade Arm (x5) 6. Downrod Clip 18. Blade (x5) 7. Downrod Pin 19. E26-base LED Bulb (x3) 8. Yoke Cover 20. Owner’s Manual 9. Set Screw (x2) 21.
DIMENSION REFERENCE D C B A A. 18.82 in. B. 13.2 in. C. 13.2 in. D. 5.13 in. MOUNTING OPTIONS Three Mounting Options Closemount Downrod Mount Angled Ceiling Mount (Up to 16 degrees) Choose one of the following mounting options: Closemount Installation is best suited for ceilings lower than 8 feet. It does not utilize the downrod. Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included).
SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS. CAUTION: All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
ASSEMBLY INSTRUCTIONS 1.Turn OFF the electrical power at the main fuse or circuit breaker. 1 Mounting Bracket Screw 2 DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Remove the mounting bracket by removing the two mounting bracket screws from the round holes in the canopy. Then loosen the other two mounting bracket screws from the J-slots. Retain the mounting bracket screws for later.
ASSEMBLY INSTRUCTIONS Downrod 5. DOWNROD MOUNT - Remove the downrod clip and downrod pin from the downrod. Then, loosen but do not remove the two set screws at the top of the yoke. Downrod Clip Downrod Pin Set Screw Yoke 5 Braided Cable 6. Feed the wires and braided cable coming from the yoke through the yoke cover, canopy and downrod. Canopy Yoke Cover Downrod Yoke Set Screw Downrod Downrod Pin Downrod Clip Downrod 6 Slot Yoke 7 Tab 8 Mounting Bracket 7.
ASSEMBLY INSTRUCTIONS Braided Cable SECONDARY HANGING SYSTEM Brace 9 Outlet Box Open Loop Support Washer For installation in the United States: Building codes in the U.S.A. do not require installation of a Secondary Hanging System. If desired, the braided cable can be cut and removed using wire cutters (sold separately). Skip to Step 12. For installation in Canada: In compliance with building codes in Canada, installation of the Secondary Hanging System is required. 9.
ASSEMBLY INSTRUCTIONS WARNING: Do NOT wire the fan motor to a wall control. Black (Hot) White (Neutral) Green White Black Blue Bare/Green (Ground) Wire Connector 12 12. Use wire connectors to connect the fan wires to the power supply wires according to the wiring diagram and the following instructions: • Connect the white wire from the fan to the white (neutral) supply wire. • Connect the black and blue wires from the fan to the black (hot) supply wire.
ASSEMBLY INSTRUCTIONS Cage Screw 16. Remove the four cage screws from the brackets inside the shade. Install the E26-base LED bulb in the socket. Then attach the light cage to the shade using the four cage screws. Repeat for each shade. Light Cage Bulb Bracket 16 Shade Switch Housing Single-pin Connector Switch Housing Screw 17 17. Remove the three switch housing screws from the top edge of the light kit.
OPERATING INSTRUCTIONS 1. Use the reverse switch, located on the switch housing to optimize your fan for seasonal performance. Reverse Switch 1 Using a ceiling fan will allow you to raise your thermostat setting in summer and lower your thermostat setting in winter without feeling a difference in your comfort. In warmer weather, push the reverse switch down which will result in downward airflow creating a wind chill effect.
TROUBLESHOOTING If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-706-3267, 9 a.m.-5 p.m. Central time. PROBLEM SUGGESTED REMEDY 1. Fan does not start: 1.
LIMITED LIFETIME WARRANTY To obtain Service, please contact the Service Department: 1-877-706-3267, 9 a.m.-5 p.m. Central time. Model Name: 52” Ceiling Fan Model No: 50650 - Bronze The manufacturer warrants this fan to be free from defects in workmanship and materials present at time of shipment from the factory for a lifetime from the date of purchase by the original purchaser.
