Prolux Hard Floor Cleaner Owners Manual For your safety please read the Owners Manual in its entirety
Congratulations on your purchase of your new Prolux Hardfloor Polisher and Cleaner! With the Prolux Hardfloor Cleaner you can quickly clean, scrub, polish, buff, wax, and shampoo. From cleaning floors to scrubbing tile to polishing floors the Prolux Hardfloor Cleaner is designed to do it all. With its 2 year warranty, simple to use design, and multiple cleaning attachments it is designed to be one of your most used appliances.
Index Page Product Specifications …...........................................................................................3 Safety Instructions….….…........................................................................................3 Parts List & Unit Description….…………………………………………………….4 Assembling the Unit …....…......................................................................................7 Using the Unit in Waxing/Polishing/Scrubbing/Waxing............................................
·During operation of the floor waxing machine, don’t tilt the waxing head or insert hands or other body parts into the bottom of the waxing head to prevent danger. ·When stopping using this floor cleaning machine or changing discs, please remove the power plug firstly. ·When using this floor waxing machine, please don’t crush or run it over the electric power wires.
Floor polishing fine pad Fine Polishing Seat Floor polishing scouring pad Rough Polishing Brush Disc Parts Description ·Rough Polishing Brush Disc:
The Rough Polishing Brush Disc is composed of Nylon brushes and is used for aggressive cleaning and scrubbing. Users tend to use this brush for tile and grout scrubbing and hardwood floor stripping. ·Fine Polishing Seat + Polishing Fine Pad: The Fine Polishing Seat + Floor Polishing Fine Pad is used for final polishing, buffing or cleaning of floor surfaces. It may also be used briefly on carpet surfaces if one of the Fine Polishing Seat + Polishing Fine Pad’s are removed.
·In order to get better polishing and cleaning effect, please uniformly polish every square yard of ground for more than one minute. ·Do not clean the Fine Polishing Seat with water to avoid degumming. Installation of Parts to Assemble Unit · Installation of handle part and extension pipe: Insert the 2 handle parts to the mounting hole until hearing “click” sound as shown in the image below.
near the roller by hand, until the Rough Polishing Brush Disc (or Fine Polishing Seat) pops off. Align at the special section hole and slightly press it · Connection of handle, extension pipe component and waxing head Connect the lower end of the extension pipe with the Polishing head connector until the locking ring can’t be rotated clockwise anymore.
·Two-handed operation (best for cleaning side to side) After left and right handles are rotated by 90° leftwards and rightwards and completely folded opened by 180°, they are available for two-handed operation. Two-handed operation can more accurately control movement direction and speed of the floor polishing machine; therefore, during fine polishing, two-handed operation mode is recommended to get excellent polishing/buffing/scrubbing/waxing effect.
Standby Mode Switch between Standby Mode and Polishing Mode. Polishing Mode ·Adjusting the handle length to fit the user Push the sliding button on the extension pipe and pull the extension pipe to adjust the length of the extension pipe.
Adjust the extension pipe length ·Properly adjust the application angle Slightly tilt the waxing head and then slightly step on it with feet to adjust the application angle of the handle. Slightly step on it with feet ·Wax oil or Cleaning Solution Loosen the Solution Knob and fill the solution container with Solution or Wax and avoid spilling. After filling, tighten the Solution knob.
·Instructions of the Polishing Machine 1. Cleaning and Check 2. Preparations 3.Start and stop Before starting the polishing work, please clean the floor and ensure that there are no granular hard objects under the Polishing machine; otherwise, your floors may be scratched. Install the Rough Polishing Brush Disc on the Unit. Adjust the metal extension pipe to a proper operation height and set the Unit with the handle locked in the upright position.
4. Solution spraying switch and indication The solution spraying switch can only control the spraying pump. When the user presses the solution spraying switch the switch turns on and a green indicator light will turn on. When this happens, it will enter into the pre programmed solution spray work cycle. This is where it will spray solution then pause for several seconds and spray solution again. It is designed so right when you run out of solution or wax on your floors then it spays again.
· Polishing can be carried out on the floor or floor tile Floor Floor Tile Polishing Fine Pad Polishing Fine Pad and Scouring Pad ·In order to get the best effect during Spraying Solution cleaning it is suggested to use non sticky solution. If solution is to sticky the floor surface and floor waxing machine may be damaged. It is important to follow any instructions from your floor manufacturer as well. Storage ·Vertical storage ① Push the extension pipe button to shorten the extension pipe.
· Storage with the unit disassembled (which can save space). ① Press down the locking button of the extension pipe and pull out the handle component upwards. ② After loosening the locking ring of the waxing head connector counterclockwise, pull out the extension pipe component.
Locking button of the extension pipe
Suggestions for settings for different floor types Part Hard Floor Laminate floor Composite floor Rocky ground Artificial stone, marble, granite, etc. Non-slip naked ceramic tile Brick surface Cement, brick, ceramic tile, etc.
Polishing Precautions 1. Before polishing, please check if there are granular hard objects (like sand) under the floor polishing machine or adhesive foreign matters on the polishing disc; otherwise, the floor waxing machine will be damaged and your floor will be scratched. Once the floor is scratched, it can’t be recovered. 2. If it is necessary to install or replace the polishing piece before or during polishing, please remove the power plug. 3. During use, please be sure to keep a Fine Polishing Seat.
Supplementary instruction of cleaning: If the surface of the Rough Polishing Brush Disc and floor polishing fine pad has condensed wax water and dirt, it can be immersed in a suitable amount of warm water with enzymatic laundry powder for about 20 minutes and then rubbed.
Warranty The manufacturer Prolux provides warranty of this Appliance for a time period of 1 year on the appliance and 2 years on the motor, starting from the date on which the appliance is sold to the end user. The repairs under warranty may only be carried out by an authorized service center. In case of warranty contact your authorized Prolux dealer you bought the unit from.
