MODEL NO: PRO1301WE Front Cover Page User Manual 13.3 Super-Slim Portable USB Monitor Version 1.00 (English) BEFORE GETTING STARTED This document is designed to aid you to get started with the device. If you experience problems following these guides or need further information pertaining to the device, please visit our website at www.prolink2u.com. All specifications are subject to the manufacturer’s configuration at the time of shipping and may change without prior notice, written or otherwise.
Table of Contents Chapter 1 Content Description P1 Section 1 Notices for using Mobile Monitor P1 Section 2 Safety Instructions P2 Section 3 Safety Precautions P2 Section 4 Product Maintenance P2 Section 5 LCD Pixel Statement P2 Section 6 Mobile Monitor and Accessories P2 Chapter 2 Installation Instructions P4 Section 1 Horizontal Display P4 Section 2 Vertical Display P5 Section 3 Upward Extension Display P6 Section 4 Dual Monitor Display P7 Section 5 Remove Mobile Monitor’s Holder Pl
1 Chapter 1 Content Description Section 1 Notices of using Mobile Monitor 1. The cable may be damaged if you pull it out by force. To disconnect power cable connector from the Mobile Monitor, please push the connector towards right hand side as illustration shown. Warning: DO NOT unplug by pulling the cord. Fig.: Push out the connector towards right hand side. 2.
2 Section 2 Safety Instructions Please read this Manual carefully and observe the operation instructions and precautionary notes. Do retain this document for future reference. Section 3 Safety Precautions 1. The Product may be severely damaged from overturning or falling. Please DO NOT place on a shaky or unstable table, cupboard or trolley. DO NOT use the product on a moving vehicle. 2.
3 2. Package Contents ： ● PRO1301WE Mobile LED Monitor x1 ● Digital Video Input and USB-Powered Y cable x1 ● Holder Plate x1 ● Double-sided adhesive tape x6 ● Non-woven bag x1 ● Quick Installation Guide x1 ● User Manual x1 Fig.: Digital Video and USB-Powered Y cable 3. Optional Accessories ● Analog Video Input and USB-Powered Y cable Fig.: Analog Video and USB-Powered Y cable ● Mini-DisplayPort (MiniDP) Input and USB-Powered Y cable Fig.
4 Chapter 2 Installation Instructions Section 1 Horizontal Display Step1. Install the Video and USB-Powered cable If you wish to use the HDMI port on the laptop, please use Digital Video and USBPowered Cable. If you wish to use the D-sub (VGA) or mini-Display Port on the laptop, please purchase the Analog Video and USB-Powered Cable or mini-Display Port and USB-Powered Cable from our authorized service center.
5 Step3. Adjust the laptop and monitor extension setting (Refer to Section 2 of Chapter 3 for monitor display setting.) After powering on the laptop, go to Windows’ "Control Panel" to adjust the monitor extension setting. If you are using Windows 7: Select "2.DVI LCD" (Digital Video) or “2. display device: VGA” (Analog Video) for Display.
6 Step2. Connect Mobile Monitor to the laptop It is recommended to place the vertical standing Mobile Monitor to the right side of the laptop for a better viewing angle.
7 Step2. Connect Mobile Monitor to the laptop Place the laptop in front of the Mobile Monitor and align the upper side of the laptop to the lower display edge of the Mobile Monitor. Connect the USB-Powered connector to the laptop's USB port, and then connect the Digital Video connector to the laptop's HDMI Video output port.
8 Fig.: Mounting the Holder Plate [Note: Do not reverse the direction of the Holder Plate as this will reverse the direction of the Mobile Monitor after installation.] Step2 Install the Video and USB-Powered cable If you wish to use the HDMI port on the laptop, please use Digital Video and USBPowered Cable.
9 2. Rotate the Mobile Monitor clockwise so that it is parallel to the laptop, open the laptop monitor and the Mobile Monitor at the same time, as illustrated. 3. Adjust the angle of the Mobile Monitor. A recommended angle is between 180° and 225°. Fig.: Rotate the Mobile Monitor to the right side, then open the laptop monitor and the Mobile Monitor at the same time. Fig. A recommended angle is between 180° and 225°. 4.
10 Step4.Adjust the laptop and monitor extension setting (Refer to Section 2 of Chapter 3 for monitor display setting.) After powering on the laptop, go to Windows’ "Control Panel" to adjust the monitor extension setting. If you are using Windows 7: Select "2.DVI LCD" (Digital Video) or “2.
11 Chapter 3 Power On and Off the Mobile Monitor Section 1 Operating Instructions 1. Initial use: when the Monitor’s USB-Powered cable is connected to a 5V DC power source (for example connected to laptop USB port), PRO1301WE will automatically switch on. 2. Switching on the Mobile Monitor from an off mode: press “Power” to switch on the Mobile Monitor. 3. Follow the steps below to proceed with the monitor display setting. 4.
12 ● At Display, select “2.DVI ● ● ● ● 2. LCD” (Digital Video) or “2. display device: VGA” (Analog Video) for Display Select "1366x768" for Resolution Select "Landscape" or "Portrait" for Orientation Select "Extend these displays" for Multiple display, and drag Display 2 to the right side of Display 1. For Duplicated mode, select "Duplicate these displays". Select OK and exit after saving the settings.
13 ● Click on Setting, select Monitor at Display, and set the Screen Resolution as 1366x768; Select "Extend my Windows desktop to this monitor" and then select ”OK” and exit. [Note: "Vertical mode" cannot be directly chosen on Windows XP system; the adjustment needs to be made via the video card. Please refer to the user manual of your video card.] 3.
14 ● Select the arrangement mode to adjust the display position of the monitors; this is the dual monitor display mode (laptop’s monitor) ● This is the upward extension mode (laptop’s monitor) 4. Setting Mac Operating System with Mobile Monitor screen for Display Effect To reduce color difference between Mobile Monitor and Mac operating system, users could follow the below instruction to adjust setting for best result.
15 Chapter 4 Using with other 3C (Computer, Communication, Consumer Electronics) Products Digital camera, Video Player, Smart Phones, Gaming Consoles or other products that support DVI output are compatible with the PRO1301WE Mobile Monitor [Note: Actual result depends on the product Video signal output format and its operation mode; not all products are compatible with full screen display on the Mobile Monitor.] 1.
16 Chapter 5 Hot Keys and OSD Instructions Note: The hot keys are capacitive sensing buttons which are activated by gentle touching. DO NOT press too hard or too fast in a continuous manner. Repeated pressing of a button will cause the button responding slow. For continuous adjustment of "Increase/ Up" or "Decrease/Down", press and hold the corresponding button for automatic continuous increase/decrease. Section 1 Hot Keys Description Power: press power switch to switch off power.
17 3. Color Setting - Brightness to launch the OSD panel. ● Press ● Press or to select ● Press or to select Brightness sub-menu and press , press to enter; press or to enter. to proceed with brightness adjustment → adjust the backlight from 0-100. Press and hold for automatic continuous decrease. exit. ● Press to 4. Color Setting – Color temperature adjustment ● Press button to launch the OSD panel.
18 6. Image Adjustment: applicable only for VGA input signal ● Press to launch the OSD panel. ● Press or to select , press to enter. ● Press or to select the sub-menu, press to enter, press or to adjust Clock → Adjust the horizontal scan rate. If the rate is incorrectly set, the vertical lines on screen and screen width will not be properly displayed. Phase → Adjust the phase of pixel clock signal.
19 Section 3 Other functions of OSD Scenario Monitor State Displays PROLiNK protection System is launched without Digital or Analog input source screen System is launched but the video signal input source is incorrectly set in the OSD. The actual connected Digital or All black; LED indicator is red Analog input source differs from the setting. System is launched with Digital or Analog input source, and the video input source is correctly set in the OSD.
20 Chapter 6 Specification Section 1 Plug and Play The Mobile Monitor conforms to VESA DDC standard and supports VESA DDC2. DDC2B is a bi-directional data channel based on I2C protocol. The host can request EDID information over the DDC2B channel. The Mobile Monitor is able to inform the host system of its identity, and depending on the level of DDC used, communicate additional information about its display capabilities.
21 2. With VGA cable Problem No screen image Screen Display Blank screen Solution Please check if the video power plug is correctly connected to the Mobile Monitor’s video power port. Please check if USB-Powered cable is connected to a 5V DC power source. Please adjust Brightness and Contrast settings, or reset them to factory default via OSD. Abnormal screen image 3.
Worldwide Customer Care Centers INDONESIA Office PT PROLiNK INTIDATA NUSANTARA Walk-In : Jl. Cideng Barat No. 79, Jakarta Pusat 10150, Indonesia. Telephone : +62 21 3483 1777 Email Support : support@prolink.co.id MALAYSIA Office FIDA SYSTEMS (M) SDN BHD Walk-In : 29 Jalan USJ 1/31, 47600 Subang Jaya, Selangor Darul Ehsan, Malaysia. Telephone : +60 3 8024 9151 Email Support : support_my@fida.
