Owner's manual

ManualsBrandsProkit's Industries ManualsPower ToolsSS-611

SS-611 HEAT GUN SET

User’s Manual

Edition

2012

Summary of content (16 pages)

PAGE 2
Contents Introduction.....................................................................................1 Description of symbols …..............................................................1 Specifications..................................................................................2 Understand your product...............................................................2 Setting up and Operation...............................................................3 Safety instructions......................
PAGE 3
Specifications SS-611A Plug type SS-611B A type I type SS-611H H type Nominal voltage 120V AC 60Hz Input power I: 750W / II: 1500W I: 750W / II: 1500W Air volume I: 280 L/min II: 480 L/min I: 280 L/min II:480 L/min Air temperature I: 300°C / II: 500°C I: 300°C / II: 500°C Insulation class Overheat Protection 230V~240V AC 50Hz Double insulated Please see page 7 Understand your product Study the operating features and safety requirements at first before using the heat gun.
PAGE 4
Setting up and operation The switch contains function of power on/off, temperature low/high. The low temperature is roughly 300°C, and high temperature is roughly 500°C. • Always ensure the power switch is at off position before plugging in. • Set power switch to I or II to heat one minute to reach its operation temperature. Always wear protective gloves and eyes protection when working. • Place the heat gun upright on a flat table carefully.
PAGE 5
CAUTION: LEAD PAINT FUMES ARE VERY HARMFUL. ALWAYS PROVIDE ADEQUATE VENTILATION WHILE WORKING INDOORS. Other functions of the heat gun set 1. 2. 3. 4. Remove paint and varnish. Remove self adhesive stickers and trim. Loosen rusted or over tightened nuts and metal screws. Thaw frozen pipes, frozen door locks, padlocks, etc. WARNING: DO NOT ATTEMPT TO THAW PLASTIC PIPS! 5. Pre-heat the natural wood grain of wooden surfaces before staining or varnishing. 6.
PAGE 6
same as that specified on the nameplate of the tool. A power source with a voltage greater than that specified for the tool can result in serious injury to the user, as well as damage to the. If in doubt, do not plug in the tool. Using a power source with a voltage less than the nameplate is harmful to the motor. Even when the tool is used as prescribed; it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the tool’s construction and design.
PAGE 7
Personal Safety 1. Stay alert, watch what you are doing when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. 2. Use safety equipment. Always wear eye protection. Safety equipment such as a dust mask, non-skid safety shoes, hard at, or hearing protection used for appropriate condition will reduce personal injuries. 3.
PAGE 8
untrained users. 5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 6. Use the power tool, accessories and tool bits etc.
PAGE 9
condition. 4. Always switch off before you put the heat gun down. 5. Do not let anyone under 18 years operate this tool. 6. Rags, cloths, cord, string and the like should never be left around the work area. 7. If you are interrupted when operating the tool, complete the process and switch off before looking up. 8. Do not block the air inlet or outlets. 9. Do not use in proximity to flammable materials. Maintenance There are no serviceable parts, no maintenance is required.
PAGE 10
目錄介紹.................................................................................................................9 符號涵義.........................................................................................................9 產品規格........................................................................................................10 瞭解產品........................................................................................................10 配置與使用......................................................
PAGE 11
產品規格 SS-611A 插頭形式 SS-611B A 插 I 插 SS-611H H 插額定電壓交流AC 120V 60Hz 交流AC 230V~240V 50Hz 輸入功率 I檔: 750W / II 檔: 1500W I 檔: 750W / II 檔: 1500W 風量 I 檔: 280 公升/分鐘 II 檔: 480 公升/分鐘 I 檔: 280 公升/分鐘 II 檔: 480 公升/分鐘溫度 I 檔: 300°C / II 檔: 500°C I 檔: 300°C / II 檔: 500°C 絕緣等級雙迴路絕緣保證過熱保護請參考第14頁了解產品在使用產品前，先熟悉操作說明和安全則。只能按照規定的範圍使用產品，禁止任何超範圍使用。 1. 馬達 2. 電源開關及溫度切換鍵 3.
PAGE 12
配置與使用     熱風槍使用簡單，開關鍵兼具電源開關和高、低溫切換功能、低熱風溫大約 300 攝氏度，高熱風溫大約 500 攝氏度。將插頭插入插座前，確保開關處於關斷位置。工作開始時，把開關設定在一檔或二檔位置，經過一分鐘左右，熱風會達到其最佳工作溫度，工作中要配帶勞保手套和防護眼鏡。小心將熱風槍直立于水準，平整的工作臺面上，風口向上，就可以騰出雙手工作，比如烘彎 PVC 管子等。清除油漆和塗料痕跡        在熟練清除油漆或油墨的工作前，需要做一些試驗，以及簡單的技巧訓練，在大面積清除之前不妨先選擇一塊小面積油漆來試驗效果。打開熱風槍，使風溫上升到設定的最高溫度，保持風咀距離作業面 7.
PAGE 13
其他適用工作： 1. 2. 3. 4. 5. 6. 7. 8. 9.
PAGE 14
作業區域 1. 保持作業區域清潔整齊，雜亂和陰暗的環境容易引發事故。 2. 不要在易燃易爆的環境中使用電動工具，比如在有易燃液體，氣體和灰塵的地方，電動工具產生的電火花容易點燃粉塵和易燃物。 3. 使用電動工具時請勿讓兒童和旁觀者靠近，分散注意力會導致失控。電氣安全 1. 插頭必須和插座原配，切勿改裝插頭，帶接地裝置的電動工具請不要用轉換插頭。無改裝的插頭，適配的插座可降低觸電危險。 2. 避免身體與接地物的表面接觸，比如水管、散熱片、爐灶和冰箱等。當您的身體處於接地狀態時會增加觸電的危險。 3. 切勿將工具暴露於雨中或潮濕環境中，水進入機器會導致觸電。 4. 不要濫用導線，不要用導線捆紮提拉工具，或直接拉拽導線拔下插頭。導線要離開熱源、油、尖銳的物體和移動的物件。破損和打絞的導線增加觸電危險。 5. 在戶外作業時，請使用符合室外作業的延長線，以減少觸電危險。人身安全 1. 使用工具時保持頭腦清醒，切勿在疲憊，服藥、飲酒和生病後作業，注意力不集中會導致事故發生。 2. 使用必要的安全防護裝置，時刻配戴眼鏡，其他安全用品如防塵口罩、防滑鞋子，耳塞等有助於保護身體，減少傷害。 3.
PAGE 15
電動工具使用和注意事項： 1. 不要超範圍使用。在設計範圍內使用電動工具會安全快捷。 2. 如開關失效請勿使用。無開關控制的電動工具很危險，一定要修理後才能使用。 3. 在做任何調整，更換配件、存放等動作之前一定要斷開電源，以確保再次啟動時的安全。 4. 妥善保管電動工具，不要讓兒童、不熟悉電動工具和操作說明的人接觸。對未加訓練的人來說，電動工具是危險的。 5. 保養電動工具。檢查運轉部件是否無偏擺和靈活，零件是否有損壞，以及其他任何影響工具工作的因素。若有損壞，先維修後使用。不少事故都是疏於維護保養而引發的。 6. 保持切割類工具鋒利和清潔。正確保養、保持切割銳利可使工作快捷而受控。 7. 不同的工作和不同的作業條件要選用正確的電動工具和附件。否則容易引發事故。警告！隨意使用不正確的附件會導致人身傷害。專門針對熱風槍的安全指示過熱保護︰當產品過熱時，會自動停止加熱，並且持續送風以加速冷卻且縮短再度啟動熱源的時間。注意! 熱風槍使用後關閉，吹風口不可朝下放置，必須平放或朝上放置，避免發熱芯餘溫損壞產品。請正確操作以延長產品使用壽命。 1.
PAGE 16
5. 6. 7. 8. 9. 18歲以下人士禁用。抹布，衣物、繩子等物品請不要放在工作區，以免引燃。如果在工作時有被打斷，請最好完成手頭工作並關斷開關。切勿堵塞進/出風口切勿在易燃易爆環境中工作。維護保養無需要定期保養的零部件。電線保養︰若電線需要更換，必須由製造商，製造商指定的機構或者有授權的服務中心進行。清潔 1. 2. 3. 隨時保持通風口通暢和清潔。定期擦拭，去除灰塵和污垢。擦拭要用乾淨的抹布，配戴護目鏡和手套。勿用腐蝕性溶劑擦拭塑膠件。注意！請用中性清潔劑和濕布擦拭。注意不要進水。一般檢查︰定期檢查，確保工具一切正常。 PROKIT’S INDUSTRIES CO., LTD. http://www.prokits.com.tw E-mail : pk@mail.prokits.com.