Instruction Manual

ManualsBrandsProkit's Industries ManualsPower ToolsPT-5201A-B

MINI GRINDER

PT-5201A/B

User’s Manual

1st Edition, 2013

Summary of content (12 pages)

PAGE 2
Component 1. Collet nut 2. Spindle lock button 3. Switch 4. Cord USER’S MANUAL Important! Please carefully read the instruction in this manual as well as the general. Safety instruction before using this appliance, keep these manuals handy. THE VARIOUS PLASTIC BAGS SHOULD NOT BE LEFT WITHIN THE REACH OF CHILDREN, RISK OF SUFFOCATION. Technical characteristics Voltage Max. diameter No load speed Vibration level Acoustic pressure less than 18VDC 3.2mm 8000~18000rpm ± 10% Less than 0.
PAGE 3
Use To use the different accessories, press the shaft locking button located to the rear of chuck, unscrew it by hand, fit the chosen accessories and hand tighten the chuck again. Accessories (1) 2 pcs grinding (3mm) stones (2) 1 pc collet (ø2.4mm) (3) 2 pcs diamond bits (5mm) ④2 pcs sanding bands 6.
PAGE 4
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Keep work area well lit. Do not use power tools near flammable liquids or gases. Guard against electric shock Prevent body contact with grounded surfaces(e.g. pipes, radiators, ranges, refrigerators, etc.). Keep children away Do not let visitors contact tool or extension cord. All visitors should be kept away from work area. Store ideal tools When not in use, tools should be stores in a dry, high, or locked-up place, out of the reach of children.
PAGE 5
14. 15. 16. 17. 18. 19. 20. 21. 22. Maintain tools with care Keep tools sharp and clean for better and safe performance. Follow instructions for lubricating and changing accessories. Inspect tool periodically and, if damaged, have them repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep Handles dry, clean and free from oil and grease.
PAGE 6
is built accordance with the relevant safety rules. Repair of electric appliances must only be carried out by experts otherwise it may cause considerable danger for the user. 23. Store these instructions for future reference. Assembly and operation Mounting an accessory Keep the spindle lock button depressed. Slacken the collect nut. Insert the shaft of the accessory into the collet.tighten the collet nut. Release the spindle lock button in order to remove the accessory, proceed in reverse order.
PAGE 7
band from the mandrel. Place the new sanding band on the mandrel Clamp all tolls as short as possible, Shafts, which stick out too far will easily bend causing the machine to vibrate. Maintenance CAUTION: Pull out the plug before maintenance Keep the machine clean Keep the air vent unimpeded Do not use the sharp material to clean the machine Do not let liquid enter into the machine to prevent it from rust HAVE YOUR POWER TOOL SERVICED BY A QUALIFIED REPAIR PERSON USING ONLY IDENTICAL REPLACEMENT PARTS.
PAGE 8
組合 1. 2. 3. 4. 夾套螺母主軸鎖定鍵開關電源線操作手冊注意! 使用設備前，請仔細閱讀本手冊中的說明以及一般的安全指示。熟練掌握操作規範，各種膠袋不應該放置在兒童觸及到的地方，以免引起窒息的風險。技術參數電壓 18VDC 夾頭最大直徑 3.2mm 無負載轉速度 8000~18000rpm ± 10% 跳動度小於 0.
PAGE 9
使用使用不同的配件時，按下主軸鎖定按鈕，鬆開夾頭螺母後的主軸旋扭，插入選擇的配件，旋緊螺母。配件圖 ① 2 個帶柄砂輪 (3mm) ② 1個夾頭 (ø2.4mm) ③ 2 個金鋼石磨針 (5mm) ④ 3 個鼓狀帶柄砂輪 (6.5x13mm) (5) 1 個尼龍刷(5mm) (6) 1 個雕刻金剛石針安全事項注意！當使用電動工具時，應遵守以下安全指示，以防止觸電及造成人身傷害和火災事故。仔細閱讀及遵守這些指示： 1. 保持工作環境整潔, 髒亂的環境容易導致人事傷害。 2. 考慮工作區環境, 不要在雨中使用電動工具；不要在潮濕的地方使用，保持工作區的乾燥；不要在接近易燃氣體或者液體的地方使用。 3. 警惕觸電, 防止身體接觸接地物表面（如水管、散熱器、冰箱等） 4. 遠離兒童, 不要讓無關者接觸工具及延長電源線，所有無關者應該遠離工作區。妥善儲存工具, 不使用時，工具應當被放在乾燥，高處或者帶鎖的地方，避免兒童觸及。 5.
PAGE 10
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 得當使用工具, 不要使用小型工具去操作違背其使用範圍的工作，例如：不使用圓鋸切割樹枝或圓木。穿著得體, 不要穿著過於寬鬆或者佩戴首飾，在操作中可能被勾住。在戶外，推薦使用防滑類鞋、橡膠手套及戴上束發頭罩。使用安全眼鏡, 在操作中需佩戴除塵口罩和耳塞，如果噪音超出70分貝，保護耳朵是必須的。測量噪音水準可以取決於工作環境及工作對象的質。使用除塵裝置, 如果在工具上裝有除塵或者收集裝置，必須確保這些裝置運用得當。不可用電源線來提工具, 不可直接拉電源線把插頭插座上拔下，不可提拉電源線移動工具，不要讓電源線接觸熱源、油和尖銳物。安全作業, 將工件夾在臺鉗上，可以更安全，並騰出出雙手工作。不要勉力而為：確保作業時站穩，保持身體平衡。工具的維護及日常護理（見後） .
PAGE 11
21. 維修、維護: 此電器是按照有關安全規則製造的，修理電器僅限於授權的專業人員進行，否則會造成人身傷害。裝配及操作一、安裝配件： 1. 按下主軸鎖定鍵鬆開夾頭螺母 2. 把配件杆插入夾頭中 3. 擰緊夾頭 4. 釋放主軸鎖定鍵移除配件時，按照步驟倒序進行。二、更換夾頭 1. 按住主軸鎖定鍵 2. 放鬆夾頭螺母 3. 移除舊夾頭螺母及夾頭 4. 放入新夾頭 5. 裝上夾頭螺母 6. 擰緊夾頭螺母 7.
PAGE 12
砂圈在磨損後可進行更換。注意：裝卡時，儘量把磨頭靠近夾頭，軸外露越長，轉動時偏擺越大。維護保養注意！保養前要斷開插頭 1. 保持工具清潔。 2. 保證工具通風良好。 3. 清潔時不用刺激性物品。 4. 防止液體和灰塵進入機身。 5. 保證產品在有資質的服務中心維修，選用合格的零件配件。寶工實業股份有限公司 PROKIT’S INDUSTRIES CO., LTD. HTTP://WWW.PROKITS.COM.TW E-MAIL : PK@MAIL.PROKITS.COM.