2 x 22 AMP HOUR HIGH PERFORMANCE JUMPSTARTER P/No.
IMPORTANT SAFETY INFORMATION Please read this manual thoroughly before use and store in a safe place for future reference. WARNINGS • Risk of explosive gas. Working in the vicinity of a lead-acid battery can be dangerous. Batteries release explosive gases during normal operation, charging and while jumpstarting a battery. Before using this jumpstarter, read and follow the instructions carefully. Follow all manufacturer’s instructions and warnings of the vehicle’s battery and other equipment being used.
FEATURES ENGINE STARTING CAPABILITIES HP2012 The HP2012 is suitable for starting 12V vehicles. 12V: Petrol vehicles up to 6 litres and diesel vehicles up to 4.5 litres HP2200 The HP2200 is suitable for starting both 12V and 24V vehicles. 12V: Petrol vehicles up to 6 litres and diesel vehicles up to 4.5 litres 24V: Petrol & Diesel vehicles up to 7 litres in capacity.
HIGH PERFORMANCE BATTERY High quality AGM battery delivers instant starting power to vehicles. Maintenance free and fully sealed battery ensures convenience and safety. 240V AND 12V RECHARGING 4A adaptor allows recharging from a 240 Volt AC outlet. The DC lead allows charging from either the 12V or 24V accessory socket.
SPECIFICATIONS Part No. HP2012 HP2200 Battery Capacity 2 x 12V 22Ah AGM 2 x 12V 22Ah AGM Battery Short Circuit Current 2000A 2200A at 12V,1100A at 24V Clamp Output 600A 640A at 12V, 500A at 24V Accessory Socket 10A 10A Heavy Duty Accessory Socket 20A 20A Protection 20A overload, 11.0V LVD (25A ATS Fuse) 20A overload, 11.0V LVD (25A ATS Fuse) Length 1.6 meters 1.
PRODUCT OVERVIEW Image of HP2200 (HP2012 not shown) 10A Accessory Socket Override Button High current & low voltage protection Battery Voltage Status Button LCD Digital Display Reverse Polarity Protection & Alarm Automatic 5 Stage Charging 20A Heavy Duty Accessory Socket L.E.D Work Light Heavy-Duty Fully Insulated Leads 1.
VEHICLE JUMPSTARTING INSTRUCTIONS NOTE: Instructions for negatively earthed vehicles only 1. Insert supplied fuse into fuse holder below charging socket. 2. Your jumpstarter should be charged for 24 hours prior to first use and as soon as possible after each use. 3. Before making any connections, check the jumpstarter battery status by pressing the red INTERNAL BATTERY STATUS button. The jumpstarter’s battery voltage should be above 12.6V in 12V mode and above 25.2V in 24V mode. 4.
UNDERSTANDING YOUR JUMPSTARTER STATUS SCREEN DISPLAY Incorrect Battery Voltage / SCREEN ILLUMINATION Screen flashing * (Scrolling Display) *Example only: Display shows actual battery voltage. Reverse Connection (+/- Alternating) Screen flashing / (Scrolling Display) Low Battery Voltage 12V Mode: less than 12.0V 24V Mode: less than 24.0V ON / (Scrolling Display) Low Battery Voltage OFF (Scrolling Display) Switched Off: less than 11.5V / Input Charge Voltage Above 30.
ALARM REMEDY Beeping Intermittently Check voltage of battery being jumpstarted.
CHARGING WITH AC ADAPTOR IMPORTANT: DO NOT POWER ANY APPLIANCE FROM THE JUMPSTARTER WHILE IT IS BEING CHARGED USING THE AC CHARGER. 1. To charge, rotate the switch on the back of the unit to ON AND CHARGING (HP2012) or 12V AND CHARGING (HP2200). 2. Plug the output end of the AC charger into the charging socket (back of jumpstarter) and connect the charger to a 240VAC outlet and turn ON. 3.
CHARGING WITH 12V DC Your Jumpstarter can be recharged from a 12V DC socket. A single-ended accessory plug and lead is included for recharging while driving. 1. To charge, rotate the switch on the back of the unit to ON AND CHARGING (HP2012) and 12V AND CHARGING (HP2200). 2. Connect the 12V charging lead to your vehicles cigarette lighter socket and to the jumpstarter’s charging socket. 3. Start the car. The vehicle’s alternator will charge both the jumpstarter and the vehicle battery at the same time.
L.E.D CHARGE INDICATORS Your jumpstarter unit features two coloured L.E.D’s that illuminate various signals to indicate different stages of charging. L.E.D Charging (Blue) L.E.
USING THE PROJECTA HP2012/HP2200 JUMPSTARTER AS A POWER SUPPLY These jumpstarter’s utilise 2 x 22Ah AGM batteries and can be used as a power supply by connecting a cigarette lighter or accessory plug into the 12V DC socket at the front of the jumpstarter. It is recommended to check the battery capacity before running accessories. Below is a list of approximate run times for various appliances.
CHECKING BATTERY CAPACITY The jumpstarter is equipped with a LCD DIGITAL DISPLAY. When the BATTERY VOLTAGE STATUS button is pressed the display will indicate the battery voltage level. To check the battery capacity : Step 1 Disconnect any appliance and accessories that might be running from the jumpstarter, as this will effect the reading. Ensure the jumpstarter is not being charged. Step 2 Press the battery voltage button and read the LED voltage display (displayed as volts).
FREQUENTLY ASKED QUESTIONS Q. How do I work out how long my appliance will run from the Jumpstarter A. When the jumpstarter is fully charged the battery will be able to provide 44 Amp hours of 12V power. If you have an appliance that uses 2.5 Amps and you use it for one hour, you have just used 2.5 Amp hours. For example:The jumpstarter is powered by 2 x 22Ah (44Ah) batteries and you are powering a small TV drawing approximately 2.5 Amps Equation: 44 Amp hours ÷ 2.5 Amps = 17.6 Hours (18 hours) Q.
Q. Why didn’t my jumpstarter start my vehicle? A. There could be a number of reasons why the jumpstarter did not start your vehicle. Check the following: 1. Ensure the jumpstarter battery is fully charged. Press the INTERNAL BATTERY STATUS button to check the condition of the battery (state of charge). Refer to page 13 (“Checking Battery Capacity”) for further information. 2. Ensure you have followed the correct operating procedure. Refer to page 7 (“Vehicle Jumpstarting Instructions”). 3.
NOTES 17
NOTES 18
WARRANTY STATEMENT Brown & Watson International Pty Ltd (“BWI”) of 1500 Ferntree Gully Road, Knoxfield, Vic., telephone (03) 9730 6000, fax (03) 9730 6050, warrants that all products described in its current catalogue will under normal use and service be free of failures in material and workmanship for a period of one (1) year from the date of the original purchase by the customer as marked on the invoice.
