@ ITEM #0760192 0760193 LED FLUSH MOUNT veggie CEILING FIXTURES .. (SET OF ) Project Source® is a registers trademark of LF, LLG. All Rights Reserved. WW MODEL #CLL9-6BZ CLL9-6BNK Franciscan. 10 Espadrille 19 LISTED ATTACH YOUR RECEIPT HERE For Damp Location Serial Number __ Purchase Date el service department at 1-866-389-8827, p.m,, EST, Monday Thursday, 8 am. Guest ions, problems, missing parts? Before returning to your retailer, call our customer 5 p.m., EST, Friday. ®® PROJECT AB15942 Loves.com SOURCE.
PACKAGE CONTENTS el A Largeness Fixture QUANTITY B Glass Shade {reassembled to endure (A)) Mounting Strap Fixture Screw {reassembled to mounting strap {C)) m Qo0 Threaded Rod (reassembled to fixture (A)) Rubber Washer (reassembled to threaded rod (E)) Washer (reassembled to threaded rod (E)) I & ™ Nut (reassembled to threaded rod (E) Finial Plate {preambled to threaded rod (E)) Finial {reassembled fo threaded rod (E}} HARDWARE CONTENTS (shown actual size) A E3 Wire Connector Machine Qty. 18 Screw Qty.
A\ safety INFORMATION READ AND SAVE THESE INSTRUCTIONS. A DANGER For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to electrical shock, fire or other injuries that could be hazardous or even fatal. + DO NOT connect this fixture to an electrical system that does not provide a means for equipment grounding.
A SAFETY INFORMATION CAUTION + TURN OFF ELECTRICITY at main fuse box (or circuit breaker box) before beginning installation by removing the fuse (or switching the circuit breaker off). « If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture. Contact a qualified, licensed electrician for information regarding the proper grounding methods as required by the local electrical code in your area.
ASSEMBLY INSTRUCTIONS 2. Remove existing fixtures and disconnect all electrical wiring. 3. Attach mounting strap (C) to outlet box (not included) using existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult a licensed electrician before proceeding. Tighten machine screws (BB) to secure mounting strap (C) to outlet box. A CAUTION: Make sure the outlet box can support 35 Ibs.
ASSEMBLY INSTRUCTIONS 4. Remove finial (J), finial plate (1), nut (H), washer (G) and rubber washer (F) from threaded rod (E). Save all for later use. Remove glass shade (B) from fixture 5. Prepare wire by stripping 3/4 in. of insulation from wire ends using wire strippers (not included). Connect WHITE wire from fixture (A) to WHITE wire from outlet box using existing wire connector or wire connector (AA).
ASSEMBLY INSTRUCTIONS 6. Wrap electrical tape (not included) around each individual wire connector (AA) down to the wire. A WARNING: Make sure no bare wire or wire strands are visible after making connections. Carefully arrange excess wiring and wire connectors (AA)} within outlet box. 7. Align key slot holes on fixture (A) with fixture screws (D) on mounting strap (C) and push up. Tum fixture (A) clockwise until it no longer tums.
ASSEMBLY INSTRUCTIONS 9. Restore power and test fixtures (A). If fixtures (A) do not function, please refer to the TROUBLESHOOTING guide on the next page. 0 CARE AND MAINTENANCE * Shut off main power supply. Wipe fixture with soft, damp cloth. Use window cleaner to clean glass. Do not use an abrasive cleaner on glass or fixture. « Total wattage for each fixture is 12 watts; do not attempt to replace the LED. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock.
WARRANTY The distributor warrants all of its lighting fixtures against defects in materials and workmanship for five (5) years from the date of purchase. If within this period the product is found to be defective, take a copy of the bill of sale as a proof of purchase and the product in its original carton to the place of purchase. The distributor will, at its option, repair, replace or refund the purchase price to the consumer.