ITEM #0752251 0756713 LED FLUSHMOUNT CEILING FIXTURES (SET OF 2) Project Source® is a registered trademark of LF, LLC. All Rights Reserved. MODEL #CLL239-2BNK CLL239-2BZ Français p. 10 Español p. 19 ATTACH YOUR RECEIPT HERE Serial Number E465631 Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-389-8827, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. 5 p.m., EST, Friday. AB15650 Lowes.
PACKAGE CONTENTS PART DESCRIPTION A Fixture B Glass Shade Mounting Strap C QUANTITY 2 2 A 2 D Fixture Screw (preassembled to Mounting Strap (C)) 4 E Threaded Rod 2 F Nut (preassembled to Threaded Rod (E)) 2 B C D E F HARDWARE CONTENTS (shown actual size) AA BB CC DD Finial Wire Connector Qty. 6 Qty. 2 Machine Screw Rubber Washer Qty. 4 Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS.
SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • DO NOT connect the bare or green insulation fixture ground wire to the black (HOT) current-carrying wire or the white neutral house wire. Connection of the bare or green fixture ground wire to the black or white house wires may cause metal parts of the fixture to carry electrical currents. Under this condition anyone coming in contact with the fixture will receive electrical shock, which could cause G serious injury or death.
SAFETY INFORMATION CAUTION • TURN OFF ELECTRICITY at main fuse box (or circuit breaker box) before beginning installation by removing the fuse (or switching the circuit breaker off). • If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture. Contact a qualified, licensed electrician for information regarding the proper grounding methods as required by the local electrical code in your area.
ASSEMBLY INSTRUCTIONS 2. Remove existing fixtures and disconnect all electrical wiring. 2 Outlet Box 3. Attach mounting strap (C) to outlet box (not included) using existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult a licensed electrician before proceeding. 3 Outlet Box Tighten machine screws (BB) to secure mounting strap (C) to outlet box.
ASSEMBLY INSTRUCTIONS 4. Prepare wire by stripping 3/4 in. of insulation from wire ends using wire strippers (not included). Connect WHITE wire from fixture (A) to WHITE wire from outlet box using existing wire connector or wire connector (AA). Connect BLUE (or BLACK) wire from fixture (A) to BLACK wire from outlet box using existing wire connector or wire connector (AA). Connect BARE/GREEN ground wire from outlet box to BARE ground wire from fixture (A) using existing wire connector or wire connector (AA).
ASSEMBLY INSTRUCTIONS 5. Wrap electrical tape (not included) around each individual wire connector (AA) down to the wire. 5 WARNING: Make sure no bare wire or wire strands are visible after making connections. AA Carefully arrange excess wiring and wire connectors (AA) within outlet box. Outlet Box AA 6. Align keyslot holes on fixture (A) with fixture screws (D) on mounting strap (C) and push up. Turn fixture (A) clockwise until it no longer turns.
ASSEMBLY INSTRUCTIONS 8. Align hole in glass shade (B) with threaded rod (E) and push up gently on glass shade (B) until threaded rod (E) comes through hole in glass shade (B). Secure glass shade (B) with rubber washer (DD) and nut (F) previously removed (Step 7, Page 7), then finial (CC). 8 A B DD CAUTION: Do not overtighten nut (F) or finial (CC) as glass may crack or break. F E Repeat Steps 3 - 8 to install second fixture. CC Hardware Used CC DD Finial x1 x1 Rubber Washer 9.
TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Light does not come on initially or no longer comes on. 1. Power is OFF. 2. Faulty connection. 3. LED component is not working properly. 1. Make sure power supply is ON. 2. Check wiring and all connections. 3. Contact customer service. Fuse blows out or circuit breaker trips. 1. Crossed wires. 2. Power wire is grounding out. 1. Check wiring. 2.