user manual Refrigerator PK1040
progress Contents Safety information Operation First use Daily use Helpful hints and tips 2 4 4 4 6 Care and cleaning What to do if… Technical data Installation Environmental concerns 7 8 10 10 14 Subject to change without notice Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings.
progress 3 • It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short-circuit, fire and/or electric shock. Warning! Any electrical component (power cord, plug, compressor) must be replaced by a certified service agent or qualified service personnel. 1. Power cord must not be lengthened. 2. Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire. 3.
progress Service • Any electrical work required to do the servicing of the appliance should be carried out by a qualified electrician or competent person. • This product must be serviced by an authorized Service Centre, and only genuine spare parts must be used. Environment Protection This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish.
progress 5 Important! In this condition, the refrigerator compartment temperature might drop below 0°C. If this occurs reset the temperature regulator to a warmer setting. Movable shelves The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired. Storage of frozen food When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run at least 2 hours on the higher settings.
progress Helpful hints and tips Hints for energy saving • Do not open the door frequently or leave it open longer than absolutely necessary. • If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator. If this happens, set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.
progress 7 Care and cleaning Caution! Unplug the appliance before carrying out any maintenance operation. This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians. water overflowing and dripping onto the food inside. Use the special cleaner provided, which you will find already inserted into the drain hole.
progress Warning! Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life.
progress 9 Problem Possible cause Solution Water flows on the ground. The melting water outlet does not Attach the melting water outlet to flow in the evaporative tray above the evaporative tray. the compressor. The temperature in the appliance is too low. The temperature regulator is not set correctly. Set a higher temperature. The temperature in the appliance is too high. The temperature regulator is not set correctly. Set a lower temperature. The door is not closed correctly.
progress Technical data Dimension of the recess Height 1030 mm Width 560 mm Depth 550 mm Rising Time 12 h The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. Installation Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.
progress 11 90° 90° Ventilation requirements The airflow behind the appliance must be sufficient. min. 200 cm2 min. 200 cm2 min 1 mm Furniture alignment Important! Make sure that the kitchen furniture is aligned vertically and at 90° in all directions. Adjust the kitchen furniture doors before installing the appliance. Important! Remove the furniture door damper if possible, to provide free space for the free movement of the appliance door.
progress b) Apply the adhesive sealing strip to the appliance as shown in figure. 4. Attach the appliance to the niche with 4 screws. 2. Install the appliance in the niche. a) Push the appliance in the direction of the arrows (1) until the upper gap cover stops against the kitchen furniture. b) Push the appliance in the direction of the arrows (2) against the cupboard on the opposite side of the hinge. I 5. Attach the covers (C, D) to the lugs and the hinge holes.
progress 13 Put together the appliance door and the furniture door and mark the holes. Ha Hb 8 mm Hc Hd 7. Install the part (Ha) on the inner side of the kitchen furniture. Ha Hb 10. Remove the brackets. Install the nail (K) 8 mm far from the outer edge of the door. ca. 50 mm 90° 8 mm 21 mm 90° ca. 50 mm 21 mm K Ha 8. Push the part (Hc) on the part (Ha). Ha Hc 9. Open the appliance door and the kitchen furniture door at an angle of 90°. Insert the small square (Hb) into guide (Ha). 11.
progress Hb Hb Hd 12. Press the part (Hd) on the part (Hb). Do a final check to make sure that: • All screws are tightened. • The sealing strip is attached tightly to the cabinet. • The door opens and closes correctly. Reversibility of the freezer door 180˚ Environmental concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
progress 15 detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.
www.progress-hausgeraete.