® 93153466_A P250074
Limited Lifetime Warranty Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to be free from defects in materials or workmanship for a period of 1 year from the date of purchase.
Safety Rules 1 Unpacking Your Fan 2 Installing Your Fan 3 Making the Electrical Connections 6 Operating Your Fan 11 Care of Your Fan 12 Troubleshooting 12 Specifications 13 Table of Contents
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity has been 2. 3. 4. 5. 6. 7. turned off at the circuit breaker or fuse box before beginning. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. CAUTION: To reduce the risk of personal injury, use only the screws provided with the electrical box.
1 6 2 7 10 2h 2 3 8 4h 3 4 OFF 1 6 a 8h b 5 R 4 9 11 5 Unpack your fan and check the contents. You should have the following items: 1. Mounting Bracket (inside canopy) 2. 6” Ball/Downrod Assembly (hanger pin and locking pin pre-attached) 3. Canopy with Canopy Ring (attached) 4. Decorative Motor Collar Cover 5. Fan Motor Assembly 6. Blades (6) 7. Light Kit Pan 8. Light Kit Fitter Assembly 9. Light Shade 10. Transmitter and Receiver 11. Extension Lead Wire a.
Tools Required Figures 1, 2, and 3 are examples of different ways to mount the electrical box. Phillips screw driver or straight slotted screw driver, adjustable wrench, step ladder, and wire cutters. Figure 3 Mounting Options If there isn’t an existing electrical box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the electrical box directly to the building structure. Use appropriate fasteners and building materials.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. 8. Make sure the grommet is properly installed in the collar cover, then slide the collar cover on the downrod until it rests on the motor housing. Be sure that the canopy and the collar cover are both oriented correctly. NOTE: This fan is recommended for standard ceiling mount using the downrod provided with this fan.
Installing Fan to the Electrical Box WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING BRACKET MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 8. 2. Install the ceiling mounting bracket on the electrical box by using the mounting screws provided with the electrical box.
Installing the Receiver into the Mounting Bracket 1. Position the house supply wires to one side of the slide-on mounting bracket; position the fan wires to the opposite side. 2. Insert the narrow end of the receiver (as shown, flat side toward ceiling) into the slide-on mounting bracket until it rests on top of the ball/downrod assembly. (Figure 10) Wiring the Receiver to the Household Wiring 1. Connect the green wire to the household ground wires using a wire connecting nut. 2.
Finishing the Fan Installation STANDARD CEILING MOUNTING Attaching the Fan Blades A HH C II WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Align the locking slots of the ceiling canopy with the two screws in the mounting plate. Push up to engage the slots and turn clockwise to lock in place.
Blade Balancing All blades are grouped by weight. Because materials vary in density, the fan may wobble even though the blades are weight matched. Touching Ceiling The following procedure should correct most fan wobble. Check after each step. 1. Check that all blade screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades.
Installing the Light Kit Pan/Light Kit Fitter Assembly CAUTION - To reduce the risk of electrical shock, disconnect the electrical supply circuit to the fan before installing the light kit. 1. Loosen but do not remove two of three mounting screws from the fan motor assembly; Remove one mounting screw. (Figure 15) 2. Push the light kit pan up to the fan motor assembly so that the two loosened screw heads fit into the keyhole slots. Turn the light kit pan clockwise, tightened the screws.
CFL 0 LEARN D 1 D 1. Remove the battery cover by pressing firmly on the arrow and sliding the cover off. CFL 0 NOTE: The remote control has already been paired to the ceiling fan for your convenience. If you have two of the same model fans in your home , please follow the steps below to control each fan independently. Mounting the remote control holder 1 Preparing the Remote Control NOTE: Screw wall anchors are included for extra support.
Remote Control Timer: While the fan is on press 2h - turns on a 2 hour run timer. While the fan is on press 4h - turns on a 4 hour run timer. While the fan is on press 8h - turns on an 8 hour run timer. Forward/Reverse: Changes direction of ceiling fan. Breeze: Press and release this button to enable the Breeze function, this will change your fan speed randomly, simulating a relaxing breeze. Fan speed: LEDs on the fan speed button will illuminate to the corresponding speed.
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start Here are some suggestions to help you maintain your fan. 2. Clean your fan periodically to help maintain its new appearance over the years.
FAN SIZE 56” SPEED Low High VOLTS 120 FAN POWER CONSUMPTION AIRFLOW CFM (WITHOUT LIGHTS) WATTS AIRFLOW EFFICIENCY (HIGHER IS BETTER) CFM/WATT 2.39 2380 995.82 35.7 6857 192.07 NET WEIGHT GROSS WEIGHT CUBE FEET 18.08 Lbs 20.95 Lbs 1.83 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
