IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference. The specifications of this product may vary from this photo and, subject to change without notice. 3810.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. STOP and contact customer service if you have any questions regarding assembly or proper operation of the Email us at: Service@paradigmhw.
TABLE OF CONTENTS SERVICE ------------------------------------------------------------------- 2 LABEL PLACEMENT --------------------------------------------------- 3 IMPORTANT SAFETY GUIDELINES ------------------------------- 4 ASSEMBLY PREPATION----------------------------------------------- 5 OVERVIEW DRAWING ------------------------------------------------ 6 PART LIST ----------------------------------------------------------------- 7 HARDWARE PACK ---------------------------------------------------
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damaged or defective product, questions, replacement parts or any other service support, please contact our customer service department by the below methods: For The Best Service, please Email: service@paradigmhw.com Response Time: 1-2 Business Days Emailing us with the information above will be the best method to receive a response during peak business hours Website: www.paradigmhw.
LABEL PLACEMENT 3
IMPORTANT SAFETY GUIDEILNES WARNING: Before using this equipment you should consult with your physician to see if this workout equipment is appropriate for you. Do not use this equipment without your physician’s approval.
ASSEMBLY PREPARATION Warning: It is highly recommended that you have assistance during the assembly of the strength equipment. 1. Tools for assembly: General tools you may need for the assembling this strength equipment: Metric Allen Key Set Metric Wrench Set and Adjustable Wrench Flat Screwdrivers Phillips Screwdrivers Rubber Mallet Silicone Spray Oil 2. Insert bolts into the frame as illustrated in the drawing of each of the steps. 3.
OVERVIEW DRAWING 6
PART LIST Part # Description Q'ty A Base Frame 2 B Upright Frame 4 C Upper Frame 2 D Pull Up Bar 1 H J Hook 2 I Long Safety Catch 2 K Rear Cross Bar 2 L L-Bracket 8 32 Hexagon Head Bolt M10*75 mm 40 67 Washer Ø10.5*Ø20*2.0t 80 75 Nylon Lock Nut M10 8.85-9.
HARDWARE PACK 8
HARDWARE PACK 9
HARDWARE PACK (161) Square End Cap 4 PCS (486) U-Bracket 2 PCS (485) Foot End Cap 4 PCS 10
PRODUCT DRAWING 11
STEP 1 1A. Insert a Foot End Cap (485) into each side of the Base Frame (A). 2 - (485) Foot End Cap 1B. Insert two Upright Frames (B) into the brackets of the Base Frame (A). Make sure the arrow stickers on the Upright Frames (B) are pointing away from the Base Frame (A). 1C. Attach the Base Frame (A) to the two Upright Frames (B) by using: 4 - (32) Hexagon Head Bolt 8 - (67) Washer 4 - (75) Nylon Lock Nut 1D. Attach the U-Bracket (486) onto the center of the Base Frame (A).
STEP 1 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 4PCS (67) Washer (75) Nylon Lock Nut 8PCS 4PCS (486) U-Bracket (485) Foot End Cap 1PC 2PCS 13
STEP 2 2A. Slide the two Upright Frames (B) into the brackets at the ends of the Upper Frame (C). 2B. Attach the Upper Frame (C) to the two Upright Frames (B) by using: 4 - (32) Hexagon Head Bolt 8 - (67) Washer 4 - (75) Nylon Lock Nut 2C. Insert a Square End Cap (161) into the both ends of the Upper Frame (C). 2 - (161) Square End Cap Do not thoroughly tighten the hardware until instructed.
STEP 2 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 4PCS (67) Washer (75) Nylon Lock Nut 8PCS 4PCS (161) Square End Cap 2PCS 15
STEP 3 3A. Insert a Foot End Cap (485) into each side of the Base Frame (A). 2 - (485) Foot End Cap 3B. Insert two Upright Frames (B) into the brackets of the Base Frame (A). Make sure the arrow stickers on the Upright Frames (B) are pointing away from the Base Frame (A). 3C. Attach the Base Frame (A) to the two Upright Frames (B) by using: 4 - (32) Hexagon Head Bolt 8 - (67) Washer 4 - (75) Nylon Lock Nut 3D. Attach the U-Bracket (486) onto the center of the Base Frame (A).
STEP 3 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 4PCS (67) Washer (75) Nylon Lock Nut 8PCS 4PCS (486) U-Bracket (485) Foot End Cap 1PC 2PCS 17
STEP 4 4A. Slide the two Upright Frames (B) into the brackets at the ends of the Upper Frame (C). 4B. Attach the Upper Frame (C) to the two Upright Frames (B) by using: 4 - (32) Hexagon Head Bolt 8 - (67) Washer 4 - (75) Nylon Lock Nut 4C. Insert a Square End Cap (161) into the both ends of the Upper Frame (C). 2 - (161) Square End Cap Do not thoroughly tighten the hardware until instructed.
STEP 4 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 4PCS (67) Washer (75) Nylon Lock Nut 8PCS 4PCS (161) Square End Cap 2PCS 19
STEP 5 5A. Mount the Pull Up Bar (D) and two L-Brackets (L) to the Upper Frame (C). 5B. Attach the Pull Up Bar (D) and two L-Brackets (L) to the Upper Frame (C) by using: 6 - (32) Hexagon Head Bolt 12 - (67) Washer 6 - (75) Nylon Lock Nut Do not thoroughly tighten the hardware until instructed.
STEP 5 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 6PCS (67) Washer 12PCS 21 (75) Nylon Lock Nut 6PCS
STEP 6 6A. Mount the Pull Up Bar (D) and two L-Brackets (L) to the Upper Frame (C). 6B. Attach the Pull Up Bar (D) and two L-Brackets (L) to the Upper Frame (C) by using: 6 - (32) Hexagon Head Bolt 12 - (67) Washer 6 - (75) Nylon Lock Nut Do not thoroughly tighten the hardware until instructed. Note: Having someone to assist for this step is recommended.
STEP 6 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 6PCS (67) Washer 12PCS 23 (75) Nylon Lock Nut 6PCS
STEP 7 7A. Attach the two Rear Cross Bars (K) and four L-Brackets (L) to the Upright Frames (B) by using: 12 - (32) Hexagon Head Bolt 24 - (67) Washer 12 - (75) Nylon Lock Nut Give the cage a shake so all the structure can settle and then thoroughly tighten ALL the hardware.
STEP 7 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 12PCS (67) Washer 24PCS 25 (75) Nylon Lock Nut 12PCS
STEP 8 A. The two Long Safety Catches (I) can be inserted into any of the holes along the Upright Frame (B). Place them at the same level on the left and right side of the cage and at a comfortable height that will assist you during your workout. B. The two Short Safety Catches (H) can be inserted into any of the holes along the Upright Frame (B). Place them at the same level on the left and right side of the cage and at a comfortable height that will assist you during your workout. C.
STEP 8 27
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PARTS REQUEST FORM Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECEIPT OF PURCHASE TO Service@paradigmhw.
