User`s manual

ManualsBrandsProForm ManualsOther470 Cx Treadmill

ASSEMBLY

ssembly requires two persons.

et the treadmill in a cleared area and remove all packing materials. Do not

dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is

coated with high-performance lubricant. During shipping, lubricant may be transferred to the top of the walking

belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubri-

cant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex keys and your own phillips screwdriver ,wire cut-

ters , and adjustable spanner .

For help identifying assembly hardware, see the drawings below. Note: If a part is not found in the part bags,

check to see if the part has been preattached.

1/4” x 1” Bolt

(88)–8

5/16” x 1” Bolt

(113)–4

1/4” Star Washer

(87)–8

1/2” Screw (52)–1

3/4” Screw (33)–5

1” Tek Screw

(123)–4

5/16” x 3 1/2” Bolt (121)–2

5/16” Washer (128)–2

1. With the help of a second person, carefully raise the

treadmill to the upright position as shown.

Insert one of the Extension Legs (86) into the treadmill as

shown. Make sure that the Extension Leg is turned so

the Base Pad (125) is underneath it. If necessary, tip the

Uprights (96) forward as you insert the Extension Leg.

Insert the other Extension Leg (not shown) in the same

way.

125

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and

follow the steps listed. If further assistance is needed, please call the telephone number on the front

over of this manual.

PROBLEM: The power does not turn on

SOLUTION:

a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 10.) If an ex-

tension cord is needed, use only a 3-conductor, 1 mm

(14-gauge) cord that is no longer than 1.5

m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the circuit breaker located on the treadmill

frame near the power cord. If the switch protrudes as

shown, the circuit breaker has tripped. To reset the

circuit breaker, wait for five minutes and then press

the switch back in.

d. Check the on/off switch located on the treadmill

frame near the power cord. Make sure that the switch

is in the “on” position.

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the

circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for

five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. Make sure that the on/off switch is in the “on” position.

e. If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION

: a.

Remove the key from the console and

UNPLUG THE

POWER CORD. With the help of another person,

carefully tip the Uprights (96) down as shown.

Remove the three 3/4” Screws (33). Note: A phillips

screwdriver with a shaft at least a 5” long is required.

ith the help of another person, carefully raise the

Uprights (96) as shown. Carefully pivot the Hood (64)

off.

Tripped

Reset

Position