Specifications

R&M Water Group
28 South 1550 West
Lindon, Utah 84042
P: [phone]
F: [phone]
© 2004 R&M Water Group All rights reserved.
ProFlow Eliminator is a registered trademark of R&M Water Group
pn: L-R-ProFlow-OM | rev: 02/04
MODEL: SA-ELIMINATOR 48 S-100 Water Softener
Operating Temperature: 34
o
–120
o
F
Operating Pressure: 25–125 psi
Voltage: 110V 60 cycles
Rated Service Flow: 12.1 GPM @ 13 psi drop
Rated Softening Capacity: 31,200 @ 7.5; 41,900 @
(Grains / Pounds of Salt) 15.2; 47,600 @ 21.2
Max Flow Rate to Drain: 4.3 GPM
Amount of High Capacity Resin: 1.5 ft
3
Rated Efficiency: 4,170 grains @ 7.5 lbs
**Observe all state and local plumbing codes.
**The efficiency of the softener is valid only at the stated salt
dosage.
**This softener conforms to WQA S-100 for the specifically claimed
performance.
Manufactured By:
R&M Manufacturing
28 South 1550 West
Lindon UT 84042-1617
[phone]
pn: LBL-ELIM-48-CERT
CAUTION: Do NOT use with water that
is microbiologically unsafe or of unknown
quality without adequate disinfection
before or after the system.
MODEL: SA-ELIMINATOR 70 S-100 Water Softener
Operating Temperature: 34
o
–120
o
F
Operating Pressure: 25–125 psi
Voltage: 110V 60 cycles
Rated Service Flow: 15.5 GPM @ 15 psi drop
Rated Softening Capacity: 48,000 @ 11.5; 64,400
(Grains / Pounds of Salt) @ 23.3; 73,100 @ 32.5
Max Flow Rate to Drain: 4.6 GPM
Amount of High Capacity Resin: 2.3 ft
3
Rated Efficiency: 4,170 grains @ 11.5 lbs
**Observe all state and local plumbing codes.
**The efficiency of the softener is valid only at the stated salt
dosage.
**This softener conforms to WQA S-100 for the specifically claimed
performance.
Manufactured By:
R&M Manufacturing
28 South 1550 West
Lindon UT 84042-1617
[phone]
pn: LBL-ELIM-70-CERT
CAUTION: Do NOT use with water that
is microbiologically unsafe or of unknown
quality without adequate disinfection
before or after the system.
MODEL: SA-ELIMINATOR 90 S-100 Water Softener
Operating Temperature: 34
o
–120
o
F
Operating Pressure: 25–125 psi
Voltage: 110V 60 cycles
Rated Service Flow: 18.0 GPM @ 15 psi drop
Rated Softening Capacity: 37,400 @ 8.8; 65,800
(Grains / Pounds of Salt) @ 25.3; 74,700 @ 35.3
Max Flow Rate to Drain: 4.1 GPM
Amount of High Capacity Resin: 2.5 ft
3
Rated Efficiency: 4,280 grains @ 8.8 lbs
**Observe all state and local plumbing codes.
**The efficiency of the softener is valid only at the stated salt
dosage.
**This softener conforms to WQA S-100 for the specifically claimed
performance.
Manufactured By:
R&M Manufacturing
28 South 1550 West
Lindon UT 84042-1617
[phone]
pn: LBL-ELIM-90-CERT
CAUTION: Do NOT use with water that
is microbiologically unsafe or of unknown
quality without adequate disinfection
before or after the system.