Specification Sheet

ManualsBrandsPROFLO ManualsPlumbingLansford 72" x 36" Drop In Acrylic Whirlpool Tub with Reversible Drain and Overflow

72 x 36

Distributed Exclusively by Ferguson and Wolseley Canada

Whirlpool

Recommended Parts

MB138883 Cable Drain PVC w/trim - CP

MB138882 Cable Drain PVC w/trim - BN

MB138884 Cable Drain PVC w/trim - ORB

MB138886 Cable Drain ABS w/trim - CP

MB138885 Cable Drain ABS w/trim - BN

MB138887 Cable Drain ABS w/trim - ORB

Warranty and Codes

This product features a 1-year limited warranty

and meets or exceeds the following standards:

Whirlpools - IAPMO PS32-84, UL listing 27E7, ANSI

Z124.1-95, ASME A112.19.8M-87R(96) and ASME

A112.19.7M-95. Baths - ANSI Z124.1-95. In an effort

to continually improve our products, design changes

may periodically be made. Ferguson reserves the

right to provide newly designed material to fill any

order unless otherwise agreed to in writing.

Installation Instructions

Never allow the weight of the tub to be supported by lip on deck or stringers, as this

could result in product failure and void the Warranty. Please inspect and test units before

install, level and fill tub with water and test for proper operation and drainage or possible

water leaks due to transit/handling damage. It is REQUIRED that the tub be supported by

the tub bottom and not the tub lip. The lip should only rest on the finished deck surface

or support stringers. The tub bottom must be supported by a setting compound such as

cement or mortar (fast cure materials are not recommended due to excessive shrinkage).

Failure to use a suitable setting compound will void the warranty. A sheet of plastic film

on top of compound, is recommended as a barrier. The tub should be set in place (do

not handle whirlpool by piping) while compound is still soft so that the compound will

conform to the tub bottom. Tub should be worked down into compound so the lip of

the tub just makes contact with finished deck surface or support stringers. It may be

necessary to partially fill tub with water to aid in properly setting the tub.

NOTE: All dimensions and specifications are nominal and may vary ± Use actual products for accuracy in critical situations.

Product Features

• Durable easy-care acrylic

construction

• Six color matched power jets

• 7.5 Amp/1.4 HP/60 HZ pump with

Nema Cord

• Molded-in armrests

• Adjustable air control for whirlpool

action

• Textured slip resistant bottom

• Air activated on/off switch

• Pre-leveled base

• Silent air induction

General Specifications

• 72” length overall

• 36” width overall

• 20” depth overall

• 50 gallon operating capacity

• 60 gallon total capacity to overflow

• Tub installation requires a single

115V/20 amp breaker and GFCI

Protected Circuit

• Ground fault circuit protection

must be provided by installer

• Prewired for simple plug-in

installation

Color Palette

• White

• Biscuit

Model Numbers

PFW7236 72” x 36” acrylic whirlpool

PFSK72RP 6’ removable panel apron

PFSK72 6’ removable apron

PFTLK Tile flange kit

Distributed Exclusively by Ferguson

Product Features

• Durable easy-care acrylic

construction

• Six color matched power jets

• High efficiency 5.6 amp pump motor

• Molded-in armrests

• Adjustable air control for

whirlpool action

• Textured slip resistant bottom

• Air activated on/off switch

• Pre-leveled base

• Silent air induction

PFW7236WH

72 x 36

Whirlpool

Model Numbers

PFW7236 72” x 36” acrylic whirlpool

PFSK72RP 6’ removable panel apron

PFSK72 6’ removable apron

PFTLK Tile flange kit

Color Palette

• White - WH

Product Specifications

Warranty and Codes

This product features a 5-year limited warranty and meets or

exceeds the following standards: Whirlpools - IAPMO PS32-

84, UL listing 27E7, ANSI Z124.1-95, ASME A112.19.8M-

87R(96) and ASME A112.19.7M-95. Baths - ANSI Z124.1-95.

In an effort to continually improve our products, design

changes may periodically be made. Ferguson reserves the

right to provide newly designed material to fill any order

unless otherwise agreed to in writing.

NOTE: All dimensions and specifications are nominal and may vary

⁄4

”. Use actual products for accuracy in critical situations.

Never allow the weight of the tub to be

supported by lip on deck or stringers, as this

could result in product failure and void the

Warranty. If utilities are available, level and fill

tub with water and test for proper operation

and drainage or possible water leaks due to

transit/handling damage.

It is REQUIRED that the tub be supported by

the tub bottom and not the tub lip. The lip

should only rest on the finished deck surface

or support stringers. The tub bottom must be

supported by a setting compound such as

cement or mortar (fast cure materials are not

recommended due to excessive shrinkage).

Failure to use a suitable setting compound

will void the warranty. A sheet of plastic film

on top of compound, is recommended as a

barrier. The tub should be set in place (do not

handle whirlpool by piping) while compound

is still soft so that the compound will conform

to the tub bottom. Tub should be worked

down into compound so the lip of the tub just

makes contact with finished deck surface

or support stringers. It may be necessary to

partially fill tub with water to aid in properly

setting the tub.

Recommended Parts

MB138843 Cable Drain PVC w/trim - CP

MB138842 Cable Drain PVC w/trim - BN

MB138844 Cable Drain PVC w/trim - ORB

MB138853 Cable Drain ABS w/trim - CP

MB138852 Cable Drain ABS w/trim - BN

MB138854 Cable Drain ABS w/trim - ORB

General Specifications

• 72” length overall

• 36” width overall

• 20” depth overall

• 50 gallon operating capacity

• 60 gallon total capacity to overflow

• Electrical service requirements: Motor 120 V.,

10.5 A., 50/60 Hz., Single Phase, Class B Insulation

• Ground fault circuit protection

must be provided by installer

• Prewired for simple plug-in installation

Installation Instructions

36"

50"

22"

18"

9 1/2"

72"

1 1/2"

20"

Shown with optional removable apron