Specification Sheet
60 x 32
Distributed Exclusively by Ferguson and Wolseley Canada
© 2015 Ferguson Enterprises, Inc. All Rights Reserved 27065 08/15
Whirlpool & Soaking Baths
Recommended Parts
MB138883 / MB138886 PVC/ABS 17”-22” Tub depth
MB138889 / MB138873 PVC/ABS 23”-27” Tub depth
Warranty and Codes
This product features a 1-year limited warranty
and meets or exceeds the following standards:
Whirlpools - IAPMO PS32-84, UL listing 27E7, ANSI
Z124.1-95, ASME A112.19.8M-87R(96) and ASME
A112.19.7M-95. Baths - ANSI Z124.1-95. In an effort
to continually improve our products, design changes
may periodically be made. Ferguson reserves the
right to provide newly designed material to fill any
order unless otherwise agreed to in writing.
Installation Instructions
Never allow the weight of the tub to be supported by lip on deck or stringers, as this
could result in product failure and void the Warranty. Please inspect and test units before
install, level and fill tub with water and test for proper operation and drainage or possible
water leaks due to transit/handling damage. It is REQUIRED that the tub be supported by
the tub bottom and not the tub lip. The lip should only rest on the finished deck surface
or support stringers. The tub bottom must be supported by a setting compound such as
cement or mortar (fast cure materials are not recommended due to excessive shrinkage).
Failure to use a suitable setting compound will void the warranty. A sheet of plastic film
on top of compound, is recommended as a barrier. The tub should be set in place (do
not handle whirlpool by piping) while compound is still soft so that the compound will
conform to the tub bottom. Tub should be worked down into compound so the lip of
the tub just makes contact with finished deck surface or support stringers. It may be
necessary to partially fill tub with water to aid in properly setting the tub.
NOTE: All dimensions and specifications are nominal and may vary ± Use actual products for accuracy in critical situations.
Product Features
• Durable easy-care acrylic
construction
• Six color matched power jets
• 7.5 Amp/1.4 HP/60 HZ pump with
Nema Cord
• Molded-in armrests
• Adjustable air control for
whirlpool action
• Textured slip resistant bottom
• Air activated on/off switch
• Pre-leveled base
• Silent air induction
General Specifications
• 60” side overall
• 32” width overall
• 19 1/2” depth overall
• 40 gallon operating capacity
• 45 gallon total capacity to overflow
• Tub installation requires a single
115V/20 amp breaker and GFCI
Protected Circuit
• Ground fault circuit protection
must be provided by installer
• Prewired for simple plug-in
installation
Color Palette
• White
• Biscuit
Model Numbers
PFW6032 60” x 32” acrylic whirlpool
PFSK60RP 5’ removable panel apron
PFSK60 5’ removable apron
PFTLK Tile flange kit
Product Features
• Durable easy-care acrylic
construction
• Six color matched power jets
• High efficiency 5.6 amp/.8 HP motor
• Molded-in armrests
• Adjustable air control for
whirlpool action
• Textured slip resistant bottom
• Air activated on/off switch
• Pre-leveled base
• Silent air induction
General Specifications
• 60” length overall
• 32” width overall
• 19 1/2” depth overall
• 40 gallon operating capacity
• 45 gallon total capacity to
overflow
• Electrical service requirements:
Motor 120 V., 10.5 A., 50/60 Hz.,
Single Phase, Class B Insulation
• Ground fault circuit protection
must be provided by installer
• Prewired for simple plug-in
installation
PFW6032WH
60 x 32
Whirlpool & Soaking Baths
Model Numbers
PFW6032 60” x 32” acrylic whirlpool
PFSK60RP 5’ removable panel apron
PFSK60 5’ removable apron
PFTLK Tile flange kit
32"
41"
22"
16"
10 1/4"
60"
1 1/2"
20"
16 1/2"
Color Palette
• White - WH
Shown with optional removable apron
Product Specifications
Recommended Parts
PF1641 PVC/ABS 17”-22” Tub depth
PF1642 PVC/ABS 23”-27” Tub depth
Warranty and Codes
This product features a 5-year limited warranty
and meets or exceeds the following standards:
Whirlpools - IAPMO PS32-84, UL listing 27E7, ANSI
Z124.1-95, ASME A112.19.8M-87R(96) and ASME
A112.19.7M-95. Baths - ANSI Z124.1-95. In an effort
to continually improve our products, design changes
may periodically be made. Ferguson reserves the
right to provide newly designed material to fill any
order unless otherwise agreed to in writing.
NOTE: All dimensions and specifications are nominal and may vary
±
1
⁄4
”.
Use actual products for accuracy in critical situations.
Installation Instructions
Never allow the weight of the tub to be supported by lip on deck or stringers, as this could result
in product failure and void the Warranty. If utilities are available, level and fill tub with water and
test for proper operation and drainage or possible water leaks due to transit/handling damage.
It is REQUIRED that the tub be supported by the tub bottom and not the tub lip. The lip should
only rest on the finished deck surface or support stringers. The tub bottom must be supported
by a setting compound such as cement or mortar (fast cure materials are not recommended
due to excessive shrinkage). Failure to use a suitable setting compound will void the warranty. A
sheet of plastic film on top of compound, is recommended as a barrier. The tub should be set in
place (do not handle whirlpool by piping) while compound is still soft so that the compound will
conform to the tub bottom. Tub should be worked down into compound so the lip of the tub just
makes contact with finished deck surface or support stringers. It may be necessary to partially
fill tub with water to aid in properly setting the tub.
Distributed Exclusively by Ferguson and Wolseley Canada
© 2009 Ferguson Enterprises, Inc. 0869 12/10