Specification Sheet

Distributed Exclusively by Ferguson and Wolseley Canada
© 2017 Ferguson Enterprises, Inc. 614925 10/17
PFW7242ALSKWH
Warranty and Codes
This product features a 5-year limited warranty and meets or
exceeds the following standards: Whirlpools - IAPMO PS32-84,
UL 1975, ANSI Z124.1-95, ASME A112.19.8M-87R(96) and
ASME A112.19.7M-95. Baths - ANSI 124.1-95. In an effort to
continually improve our products, design changes may periodi-
cally be made. Ferguson reserves the right to provide newly
designed material to fill any order unless otherwise agreed to
in writing.
Installation Instructions
Never allow the weight of the tub to be supported by lip on deck or stringers,
as this could result in product failure and void the Warranty. If utilities are
available, level and fill tub with water and test for proper operation and drain-
age or possible water leaks due to transit/handling damage. It is REQUIRED
that the tub be supported by the tub bottom and not the tub lip. The lip should
only rest on the finished deck surface or support stringers. The tub bottom
must be supported by a setting compound such as cement or mortar (fast
cure materials are not recommended due to excessiveshrinkage). Failure to
use a suitable setting compound will void the warranty. A sheet of plastic film
on top of compound, is recommended as a barrier. The tub should be set in
place (do not handle whirlpool by piping) while compound is still soft so that
the compound willconform to the tub bottom. Tub should be worked down into
compound so the lip of the tub just makes contact with finished deck surface
or support stringers. It may be necessary to partially fill tub with water to aid in
properly setting the tub.
Model Numbers
PFW7242ALSK 72" x 42" whirlpool with
integral skirt - left hand drain
PFW7242ARSK 72" x 42" whirlpool with
integral skirt - right hand drain
PFS7242LSK 72" x 42" soaking bath with
integral skirt - left hand drain
PFS7242RSK 72" x 42" soaking bath with
integral skirt - right hand drain
MIRPRESSHTR Whirlpool heater
Recommended Parts
MB644BN 17-22 PVC Cable drain w/ trim - BN
MB644CP 17-22 PVC Cable drain w/ trim - CP
MB644ORB 17-22 PVC Cable drain w/ trim - ORB
MB643BN 17-22 ABS Cable drain w/ trim - BN
MB643CP 17-22 ABS Cable drain w/ trim - CP
MB643ORB 17-22 ABS Cable drain w/ trim - ORB
Product Features
• Durable easy-care acrylic
construction
• Air activated on/off switch
• Textured slip-resistant bottom
• Eight adjustable color matched
hydro jets, including two lumbar jets
• Integral tile flange
• Heater blank, safety suction and
silent air induction
• Available as an invigorating
whirlpool and an unjetted soaking bath
General Specifications
• 72" length overall
• 42" width overall
• 19 3/4" height overall
• 55 gallon operating capacity
• 80 gallon total capacity to overflow
• Prewired for simple plug-in installation
• Requires a single 115V/20 amp
GFCI circuit
• Available in white and biscuit
72 x 42 Plus A Series
Skirted Whirlpool & Soaking Baths
Product Specifications
With Integral Skirt
NOTE: All dimensions and specifications are nominal and may vary ±
1
/
4
".
Use actual products for accuracy in critical situations.
42"
18 3/4"
19 3/4"
1/2"
1"
2 1/2"
16 1/4"
48"
30"
72"
8"
42"
21"
22"
2 1/4"
Risers Installed
Above Floor Rough Model
C