Installation Sheet

Installation Instructions
High Efficiency Flush Valve
Bowl, Floor Mount
Tools and Materials
A: Screwdriver; B: Wrench; C: Tape Measure;
D: Level; E: Drill; F: Flange; G: Wax Seal;
H: Marker; I: Plugs; J: Screw Fixation;
K: Flexible Connector; L: Adapter
1. Temporarily install T-Bolts into the flange,
set bowl, and place discs onto the bolts.
Mark the bolt length for bowl cap clearance.
Remove bowl and cut the bolts to marked
length. (figure 1)
2. Carefully turn the bowl upside down onto
padded surface to protect the glazed
surface. Place a new wax ring gasket
onto the bowls outlet. (figure 2) A bead of
setting caulk may be applied to the base,
if desired.
3. Install the 2 flange T-bolts in the mounting
flange. (Figure1)
4. Carefully install the bowl so that the T-Bolts
protrude through the mounting holes on the
foot of the bowl (Figure 3)
5. Apply full body weight pressure downward
evenly on the bowl for proper gasket seal.
6. Place discs (bevel side out) and nuts onto
T-bolts and tighten nuts.
Flushometer Valve Installation
NOTE: For proper operation product requires
30 psi working line pressure. Use the flush valve
manufacturer’s installation instructions for installing
the valve and for adjusting the water usage.
Care & Maintenance
Do not use abrasive powered or liquid cleaners
which can damage the product surface.
Caution
Product is Fragile. To avoid breakage and
possible injury handle with care!
Warranty
WHAT IS COVERED?
Ferguson Enterprises, Inc. “Ferguson” or the
“Company” warrants its products to be free from
defects in material and workmanship under normal
use and service FOR A PERIOD OF ONE (1) YEAR
FROM THE DATE OF INSTALLATION.
WHAT IS NOT COVERED?
The warranty set forth in paragraph 1 does not cover
installation or any other labor charges and does not
apply to products which have been damaged as a
result of any accident, abuse, improper installation
or maintenance, or modification of original plumbing
product. The warranty of such products is limited to
the warranty extended to Ferguson by the product
manufacturer. Finally, FERGUSON SHALL NOT BE
RESPONSIBLE OR LIABLE FOR ANY FAILURE OR
DAMAGE TO THIS PRODUCT OR ANY COMPONENT
THEREOF CAUSED BY THE USE OF ABRASIVE
CLEANERS.
HOW TO OBTAIN WARRANTY SERVICE
US Customers:
The purchaser should contact their local Ferguson
location, installing contractor or builder from whom the
product was purchased. To find you nearest Ferguson
location please visit www.ferguson.com and enter in
your address into the Find a Location field.
Canadian Customers:
The purchaser should contact their local Wolseley
Canada location, installing contractor or builder from
whom the product was purchased. To find your
nearest Wolseley Canada location please visit www.
wolseleyinc.ca, then click on Find a Location and enter
your address into the location field.
PROFLO is a registered trademark of Ferguson
Enterprises, Inc.
LIMITATIONS OF IMPLIED WARRANTY AND
DISCLAIMER OF CONSEQUENTIAL OR INCIDENTAL
DAMAGES FERGUSON DISCLAIMS ANY LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES AND
DISCLAIMS ALL EXPRESS OR IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, AS SET
FORTH ABOVE. IMPLIED WARRANTIES OF THE
PRODUCTS AND PRODUCT COMPONENTS SET
FORTH IN PARAGRAPH 1 ABOVE ARE LIMITED TO
THE DURATIONS OF THE RESPECTIVE WARRANTY.
Some states do not allow the exclusion or limitation
of incidental or consequential damages or limitations
on how long an implied warranty lasts, so the above
limitations may not apply to you. This warranty gives
you specific legal rights and you may also have other
rights, which vary from state to state.
WAX RING
SEALANT
FLANGE
FLANGE BOLTS
A
Figure 2
Figure 1
Figure 3
Ｇ
Ｉ
Ｊ
Ａ
Ｂ
Ｃ
Ｄ
Ｅ
Ｈ
Ｋ
Ｆ
Ｌ
Temporarily install T-bolts into the flange, set the bowl, and place discs onto the bolts. Mark the bolt length for bolt
cap clearance. Remove bowl and cut the bolts to marked length. (Figure 1)
Carefully turn the bowl upside down onto a padded surface to protect the glazed surface. Place a new wax ring
gasket onto the bowl’s outlet. (Figure 2) A bead of setting caulking may be applied to the base, if desired.
Install the 2 flange T-bolts in the mounting flange. (Figure 1)
Carefully install the bowl so that the T-bolts protrude through the mounting holes on the foot of the bowl. (Figure 3)
Apply full body weight pressure downward evenly on the bowl for proper gasket seal.
Tynan Plumbing Fixtures Limited Warranty
Who Is Covered?
The warranty covers the original purchaser or first home owner
What is the Warranty Period?
The warranty is for one year form installation date or purchase of home
What Does the Warranty Not Cover?
installation and labor costs you incurred
Repair costs and damage due to leaks from supply line failures
Products not installed per Tynan’s instructions
Product that were subject to abuse or misuse
Products that do not meet local building code requirements
Products with faulty maintenance
What Will We Do to Correct Problems?
We will repair or replace the product with a replacement model
What Do you do to get Service?
You may contact the place of purchase or Tynan Plumbing Fixtures at
[e-mail]
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defective in materials
or workmanship
Tynan Plumbing Fixtures, LLC
P.O. Box 33178
Palm Beach Gardens FL 33420
Place discs (bevel side out) and nuts onto T-bolts and tighten nuts.
Do not use abrasive powered or liquid cleaners which can damage the product surface
Caution: Product is Fragile. To avoid Breakage and possible injury handle with care!
CARE＆ MAINTENANCE
Use the flush valve manufacturer’s installation instructions for installing the valve and for adjusting the water usage.
FLUSHOMETER VA LVE INSTALLATION
NOTE: For proper operation product requires 30 psi working line pressure
WAX RING
SEALANT
FLANGE
FLANGE BOLTS
A
Figure 2
Figure 1
Figure 3
Ｇ
Ｉ
Ｊ
Ａ
Ｂ
Ｃ
Ｄ
Ｅ
Ｈ
Ｋ
Ｆ
Ｌ
Temporarily install T-bolts into the flange, set the bowl, and place discs onto the bolts. Mark the bolt length for bolt
cap clearance. Remove bowl and cut the bolts to marked length. (Figure 1)
Carefully turn the bowl upside down onto a padded surface to protect the glazed surface. Place a new wax ring
gasket onto the bowl’s outlet. (Figure 2) A bead of setting caulking may be applied to the base, if desired.
Install the 2 flange T-bolts in the mounting flange. (Figure 1)
Carefully install the bowl so that the T-bolts protrude through the mounting holes on the foot of the bowl. (Figure 3)
Apply full body weight pressure downward evenly on the bowl for proper gasket seal.
Tynan Plumbing Fixtures Limited Warranty
Who Is Covered?
The warranty covers the original purchaser or first home owner
What is the Warranty Period?
The warranty is for one year form installation date or purchase of home
What Does the Warranty Not Cover?
installation and labor costs you incurred
Repair costs and damage due to leaks from supply line failures
Products not installed per Tynan’s instructions
Product that were subject to abuse or misuse
Products that do not meet local building code requirements
Products with faulty maintenance
What Will We Do to Correct Problems?
We will repair or replace the product with a replacement model
What Do you do to get Service?
You may contact the place of purchase or Tynan Plumbing Fixtures at
[e-mail]
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defective in materials
or workmanship
Tynan Plumbing Fixtures, LLC
P.O. Box 33178
Palm Beach Gardens FL 33420
Place discs (bevel side out) and nuts onto T-bolts and tighten nuts.
Do not use abrasive powered or liquid cleaners which can damage the product surface
Caution: Product is Fragile. To avoid Breakage and possible injury handle with care!
CARE＆ MAINTENANCE
Use the flush valve manufacturer’s installation instructions for installing the valve and for adjusting the water usage.
FLUSHOMETER VA LVE INSTALLATION
NOTE: For proper operation product requires 30 psi working line pressure
WAX RING
SEALANT
FLANGE
FLANGE BOLTS
A
Figure 2
Figure 1
Figure 3
Ｇ
Ｉ
Ｊ
Ａ
Ｂ
Ｃ
Ｄ
Ｅ
Ｈ
Ｋ
Ｆ
Ｌ
Temporarily install T-bolts into the flange, set the bowl, and place discs onto the bolts. Mark the bolt length for bolt
cap clearance. Remove bowl and cut the bolts to marked length. (Figure 1)
Carefully turn the bowl upside down onto a padded surface to protect the glazed surface. Place a new wax ring
gasket onto the bowl’s outlet. (Figure 2) A bead of setting caulking may be applied to the base, if desired.
Install the 2 flange T-bolts in the mounting flange. (Figure 1)
Carefully install the bowl so that the T-bolts protrude through the mounting holes on the foot of the bowl. (Figure 3)
Apply full body weight pressure downward evenly on the bowl for proper gasket seal.
Tynan Plumbing Fixtures Limited Warranty
Who Is Covered?
The warranty covers the original purchaser or first home owner
What is the Warranty Period?
The warranty is for one year form installation date or purchase of home
What Does the Warranty Not Cover?
installation and labor costs you incurred
Repair costs and damage due to leaks from supply line failures
Products not installed per Tynan’s instructions
Product that were subject to abuse or misuse
Products that do not meet local building code requirements
Products with faulty maintenance
What Will We Do to Correct Problems?
We will repair or replace the product with a replacement model
What Do you do to get Service?
You may contact the place of purchase or Tynan Plumbing Fixtures at
[e-mail]
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defective in materials
or workmanship
Tynan Plumbing Fixtures, LLC
P.O. Box 33178
Palm Beach Gardens FL 33420
Place discs (bevel side out) and nuts onto T-bolts and tighten nuts.
Do not use abrasive powered or liquid cleaners which can damage the product surface
Caution: Product is Fragile. To avoid Breakage and possible injury handle with care!
CARE＆ MAINTENANCE
Use the flush valve manufacturer’s installation instructions for installing the valve and for adjusting the water usage.
FLUSHOMETER VA LVE INSTALLATION
NOTE: For proper operation product requires 30 psi working line pressure
WAX RING
SEALANT
FLANGE
FLANGE BOLTS
A
Figure 2
Figure 1
Figure 3
Ｇ
Ｉ
Ｊ
Ａ
Ｂ
Ｃ
Ｄ
Ｅ
Ｈ
Ｋ
Ｆ
Ｌ
Temporarily install T-bolts into the flange, set the bowl, and place discs onto the bolts. Mark the bolt length for bolt
cap clearance. Remove bowl and cut the bolts to marked length. (Figure 1)
Carefully turn the bowl upside down onto a padded surface to protect the glazed surface. Place a new wax ring
gasket onto the bowl’s outlet. (Figure 2) A bead of setting caulking may be applied to the base, if desired.
Install the 2 flange T-bolts in the mounting flange. (Figure 1)
Carefully install the bowl so that the T-bolts protrude through the mounting holes on the foot of the bowl. (Figure 3)
Apply full body weight pressure downward evenly on the bowl for proper gasket seal.
Tynan Plumbing Fixtures Limited Warranty
Who Is Covered?
The warranty covers the original purchaser or first home owner
What is the Warranty Period?
The warranty is for one year form installation date or purchase of home
What Does the Warranty Not Cover?
installation and labor costs you incurred
Repair costs and damage due to leaks from supply line failures
Products not installed per Tynan’s instructions
Product that were subject to abuse or misuse
Products that do not meet local building code requirements
Products with faulty maintenance
What Will We Do to Correct Problems?
We will repair or replace the product with a replacement model
What Do you do to get Service?
You may contact the place of purchase or Tynan Plumbing Fixtures at
[e-mail]
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defective in materials
or workmanship
Tynan Plumbing Fixtures, LLC
P.O. Box 33178
Palm Beach Gardens FL 33420
Place discs (bevel side out) and nuts onto T-bolts and tighten nuts.
Do not use abrasive powered or liquid cleaners which can damage the product surface
Caution: Product is Fragile. To avoid Breakage and possible injury handle with care!
CARE＆ MAINTENANCE
Use the flush valve manufacturer’s installation instructions for installing the valve and for adjusting the water usage.
FLUSHOMETER VA LVE INSTALLATION
NOTE: For proper operation product requires 30 psi working line pressure
Distributed exclusively by Wolseley’s North American Division, Ferguson, Stock Building Supply and Wolseley Canada
©2008 Wolseley 0335 10/09