Care and Use Guide

Distributed Exclusively by Ferguson and Wolseley Canada
© 2014 Ferguson Enterprises, Inc. All Rights Reserved 18776 01/14
Pedestal Lavatory
Care & Maintenance
Do not use abrasive powered or liquid cleaners
which can damage the product surface
Caution: Product is Fragile. To avoid breakage and
possible injury handle with care!
Installing Pedestal Lavatory
1. Determine the sink position on the wall. If
this is a new installation, remove drywall and
mortise a 2x6 board for suitable reinforcement
behind the finished wall as shown in E above.
Re-Finish the dry wall and paint. Placement of
the wall hanger support, (2), will be determined
by temporarily placing the pedestal lavatory on
top of the pedestal. Support the sink temporarily
with two 2x4 braces cut to proper length
2. With a pencil, mark the location of the pedestal
on the finished floor by tracing around the
pedestal foot. Mark the lavatory height and
sides. If supplied, slide the hanger support up
behind the pedestal lavatory until it contact the
china lavatory and mark the holes with a pencil.
3. Remove the sink and pedestal. Bore pilot holes
into the markings made earlier. These holes
will be used for the lag screws that will hold
the hanger, (2), in place. Note: Models are not
Installation Instructions
all supplied with lag bolts, anchor screws
and steel hangers. Various lag bolt sizes
for numerous installations are available to
the installer at most local hardware stores.
Secure the lavatory hanger, (1) if available, to
the wall using the appropriate lag bolts and
washers.
4. Install the faucet,(5) onto the lavatory, (3),
per the faucet manufactures instructions.
It is easier to install it before the lavatory
is installed on the pedestal and against the
finished wall.
5. Place the lavatory, (3) on top of the pedestal,
(5) and gently slide back both toward the
wall and to the pedestal outline made on the
finished floor. Lift the lavatory on top of the
hanger, if supplied. Some lavatories have
anchor holes located on the back sides of
the sink, location C above. Lag bolts with
washers sized to fit into these holes should
be installed and tightened to prevent the
lavatory from lifting off the wall. A pilot hole
may need to be drilled to securely anchor
the lag bolts. Make sure the lavatory is
leveled before tightening these bolts.
If anchor holes are present in the pedestal
foot, follow step 6. If not, skip step 6 and
move to step 7.
6. Drill holes through the pedestal foot, (5),
into the finished floor, per (B) above. Anchor
the pedestal leg down to the floor using
washers and lag bolts. (not supplied). See
D. above
7. Connect the drain assembly and trap as
well as the hot and cold water supply lines.
Check for leaks.
Installation Instructions
Pedestal Lavatory
Installing Pedestal Lavatory
1. Determine the sink position on the wall. If
this is a new installation, remove drywall and
mortise a 2x6 board for suitable reinforcement
behind the finished wall as shown in E above.
Re-Finish the dry wall and paint. Placement of
the wall hanger support, (2), will be determined
by temporarily placing the pedestal lavatory
on top of the pedestal. Support the sink
temporarily with two 2x4 braces cut to proper
length
2. With a pencil, mark the location of the pedestal
on the finished floor by tracing around the
pedestal foot. Mark the lavatory height and
sides. If supplied, slide the hanger support up
behind the pedestal lavatory until it contact the
china lavatory and mark the holes with a pencil.
3. Remove the sink and pedestal. Bore pilot holes
into the markings made earlier. These holes will
be used for the lag screws that will hold the
hanger, (2), in place. Note: Models are not all
supplied with lag bolts, anchor screws and steel
hangers. Various lag bolt sizes for numerous
installations are available to the installer at
most local hardware stores.Secure the lavatory
hanger, (1) if available, to the wall using the
appropriate lag bolts and washers.
4. Install the faucet,(5) onto the lavatory, (3), per
the faucet manufactures instructions. It is easier
to install it before the lavatory is installed on the
pedestal and against the finished wall.
5. Place the lavatory, (3) on top of the pedestal,
(5) and gently slide back both toward the wall
and to the pedestal outline made on the finished
floor. Lift the lavatory on top of the hanger, if
supplied. Some lavatories have anchor holes
located on the back sides of the sink, location C
above. Lag bolts with washers sized to fit into
these holes should be installed and tightened
to prevent the lavatory from lifting off the wall.
A pilot hole may need to be drilled to securely
anchor the lag bolts. Make sure the lavatory is
leveled before tightening these bolts.
6. Drill holes through the pedestal foot, (5), into
the finished floor, per (B) above. Anchor the
pedestal leg down to the floor using washers
and lag bolts. (not supplied). See D. above
7. Connect the drain assembly and trap as well
as the hot and cold water supply lines. Check
for leaks.
FINISHED
FLOOR
FINISHED
WALL
2
2
4
3
B
5
Estimated Heights
C
E
C
A
A
Rear
View
Pedestal
Screws
D.
Anchor
Screws
Hanger
2 x 6 support
2
through
812
29 12
-/"
-/"
A
Care & Maintenance
Do not use abrasive powered or liquid cleaners
which can damage the product surface
Caution: Product is Fragile. To avoid breakage and
possible injury handle with care!
©2008 Wolseley Distributed exclusively by Wolseley North American Division: Ferguson, Stock Building Supply and Wolseley Canada. 1558 07/08