Owner's manual

ManualsBrandsProface ManualsComputer HardwareGP4600R - 12.1 Standard HMIs with Rear Mounting Options"

USB/RS-422/485

Conversion Adapter

Installation Guide

This product, hereafter referred to as the

“Conversion Adapter”, converts the USB

port on the Display (for models listed in the

“Corresponding Units” section in this guide)

into a RS-422/485 serial interface.

• When using this product with a Display

unit, the external devices you can

connect to this product’s serial

interface (RS-422/485) are limited. For

more information, please refer to the

following manuals:

• Reference Manual

• Device/PLC Connection Manual

• Pro-face Home Page

“Otasuke Pro!” support site

URL: http://www.pro-face.com/otasuke/

Safety Precautions

• When disposing of this product, follow

your country's regulations for similar

types of industrial waste.

Package Contents

(1) USB/RS-422/485 Conversion Adapter

(1) (PFXZCBCBCVUSR41)

(2) Attachment Screws (2)

(3) Installation Guide <this document>

This product has been carefully packed with

special attention to quality. However, should

you find anything damaged or missing,

please contact your local distributor.

WARNING

HAZARD OF ELECTRIC SHOCK OR EXPLO-

SION

• Do not disassemble or remodel the Conver-

sion Adapter in any way. Doing so may cause

an electric shock or fire.

• Do not use the Conversion Adapter in areas

where flammable gases are present. Doing

so may cause an explosion.

• Do not allow water to enter the connector. Do

not touch the connector with wet hands.

Doing so may cause an electric shock.

Failure to follow these instructions can result

in death, serious injury, or equipment damage.

WARNING

UNINTENDED EQUIPMENT OPERATION OR

LOSS OF CONTROL

• Do not use the USB/RS-422/485 Conversion

Adapter at temperatures outside the range

specified in this guide.

• Do not use or store the Conversion Adapter

at very high temperatures.

• Do not use or store the Conversion Adapter

in direct sunlight or excessively dusty or dirty

environments.

• Do not use or store the Conversion Adapter

in an environment where it may be exposed

to chemical vapors or fumes.

Failure to follow these instructions can result

in death, serious injury, or equipment damage.

NOTICE

LOSS OF COMMUNICATION

• Do not connect or disconnect the USB/RS-

422/485 Conversion Adapter during commu-

nication. Doing so may cause a communica-

tion error.

Failure to follow these instructions can result

in equipment damage.

Summary of content (7 pages)

PAGE 1
USB/RS-422/485 Conversion Adapter Installation Guide WARNING UNINTENDED EQUIPMENT OPERATION OR LOSS OF CONTROL • This product, hereafter referred to as the “Conversion Adapter”, converts the USB port on the Display (for models listed in the “Corresponding Units” section in this guide) into a RS-422/485 serial interface. • • • • When using this product with a Display unit, the external devices you can connect to this product’s serial interface (RS-422/485) are limited.
PAGE 2
Corresponding Units Model Conditions GP4000 Series (except GP-4100 Series or GP-4*01TM) Remarks For information on supported models including types and specifications, refer to the Project file from GP-Pro EX corresponding hardware Ver3.00 or later (same manual for your Display or version as the Transfer Tool) refer to the Pro-face Home is transferred to the Display. Page. URL http://www.pro-face.
PAGE 3
Electrical Environment Noise immunity Noise Voltage: 1000 Vp-p Pulse Width: 1 µs Rise Time: 1 ns Electrostatic Discharge Immunity Contact Discharge Method: 6 kV (IEC/EN61000-4-2 Level 3) External Specifications External Dimensions W110 x H40 X D27 mm (W4.33 x H1.57 x D1.06 in.) Cable length 0.5m (1.64 ft) (include connection parts) Weight 150 g (0.
PAGE 4
Interface RS-422/RS-485 Interfit Bracket #4-40 inch screws Pin Arrangement 5 1 9 6 Pin # RS-422/RS-485 Signal Name Meaning 1 RDA 2 RDB Receive Data B(-) 3 SDA Send Data A(+) 4 ERA Data Terminal Ready A(+) 5 SG Signal Ground 6 CSB Send Possible B(-) 7 SDB Send Data B(-) 8 CSA Send Possible A(+) 9 ERB Data Terminal Ready B(-) FG Frame Ground Shell Receive Data A(+) • Use the DIP switch on the Conversion Adapt
PAGE 5
Dimensions Units: mm [in.] 110[4.33] 27[1.06] USB Connector 40[1.57] Serial Connector External Device side Display side DIP Switch 500[19.68] Attachment Method • For the GP-4200 series, attach the Conversion Adapter to the panel. Attaching the Conversion Adapter directly to the Display 75[2.
PAGE 6
• Make sure the Conversion Adapter is placed inside the edges of the Display. 1) Attach one screw to the Display’s rear side. Use a torque of 0.5 N•m to 0.6 N•m (4.4 lb-in to 5.3 lb-in). Correct Rear face of Display 2) Attach the Conversion Adapter to the Display. Incorrect Rear face of Display 3) Slide the Conversion Adapter in the direction of the arrow so the Conversion Adapter is hooked by the screw from step 1. Rear face of Display • Do not place the Conversion Adapter over the slits.
PAGE 7
Attaching the Conversion Adapter to a Panel Inquiry When attaching the Conversion Adapter to a panel other than the Display’s main unit, attach it at the two points identified in the diagram below. Drill holes suitable for screws as shown in the diagram. For attachment information, refer to “Attaching the Conversion Adapter directly to the Display”. If you experience difficulties or have questions about this product, please contact us any time.