FP-3710T Series Installation Guide Caution Be sure to read the “Warning/Caution Information” on the attached sheet before using the product. Package Contents FP unit (1) Installation Guide (1) (this manual) Installation Gasket (1)(attached to the FP unit) Installation Brackets (4/set, 2sets) Warning/Caution Information (1) AC Power Cord (1) USB Cable Clamp(1) AC Power Connector (1) (attached to the FP unit) This unit has been carefully packed, with special attention to quality.
Required software/Reference manual An FP-3710T series unit needs the following software for operation. As FP user manual, provided by PDF media, describes its details, download the manual below and get the further information. Visit our website below and get both software and reference manual. (URL:http://www.pro-face.com/otasuke/) • Software : Mouse Emulation Software • Manual : FP-3710T series User Manual UL/c-UL/CSA Application Notes The FP-3710T Series is a UL/c-UL/CSA listed product. (UL File No.
1 Part Names Front View I J A,B Rear View C D E F Bottom View G H A: TFT Color LCD Acts as a display monitor for your host. B: Touch Panel Allows you to switch screens or write data to the host. C: Power Connector (Socket) Provides the input and ground terminals for a power cable. D: Setting Switch By opening the cover, the Dip switches and slide switch are seen. Each switch can set a operation mode.
2 Dimensions Top View Unit: mm [in] 383 [15.08] 294 [11.57] Front View 3 282 [11.10] 60 [2.36] 5 [0.20] 395 [15.55] Side View Dip Switches and Slide Switch The Dip Switches and Slide Switch are located in the bottom of the FP unit. Only the settings when the power supply is turned on is effective to the Dip Switches and the Slide Switch. After changing the settings of the Dip Switches and the Slide Switch, be sure to restart your FP unit.
4 Interfaces Analog RGB Interface Input signal type Input signal characteristic Setting by OSD (On Screen Display) Analog RGB Image signal : analog RGB Synchronous signal :TTL level, negative true or positive true Scanning type : non-interlace •BRIGHTNESS •CONTRAST •H-POSITION •V-POSITION •H-size •PHASE •DIMMER(BACKLIGHT) •SHARPNESS •ALL RESET (DEFAULT) The number of dots (pixels) displayed are as follows: H Sync. (kHz) Size 640x400 640x400 640x480 640x480 640x480 24.827 31.469 31.469 37.500 35.
Pin Assignments and Signal Names for Analog RGB Pin No Signal Name Condition 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Analog R Analog G Analog B Reserved Digital grounding Return R Return G Return B Reserved Digital grounding Reserved DDC DATA H. SYNC V.
*1. When you use this resolution, set “ON” for “720 × 400 Mode” in the OSD (On Screen Display) “System Settings”.
*1 The CD, DTR, and DSR are connected together inside of the FP. Connector.................. Dsub 9 pin female Connector set screw.. Inch type (4-40) Cable ......................... SIO cable for FP manufactured by Pro-face. (FP61V-IS00-O) Concerning Signal Names Signal names used for the serial interface on FP units are designed to match the pin order used on most PC serial interfaces, so that a straight cable can be used to connect the two.
(2) Check that FP has instllation fastners. Insert the FP from the front. • Installation gasket must be used even though it is not necessary for its environment. For installation, refer to the FP-3710T series User Manual. (3) The following figures show the eight(8) fastener insertion slot locations. Insert each fastener's hook into the slot and tighten it with a screwdriver.
AC1500V 20mA for 1 minute (between charging and FG terminals) DC500V 10MΩ (Min.) Voltage Endurance Insuration Resistance (between charging and FG terminals) Environmental Specification Item Surrounding Air Temperature Storage Temperature Ambient Humidity Storage Humidity Air Purity (Dust) Pollution Degree Specification 0~50ºC (The panel should not incline more than 30º) -20 ~ +60ºC 10~90%RH (No condensation, Wet bulb temperature: 39ºC max.) 0.1mg/m3 (Max.
Connecting the Power Cord When connecting the AC type power cord, be sure to follow the procedures given below. (1) Confirm that the power cord is unplugged from the power supply. (2) Push the Opening button by a small and flat screw driver to open the desired pin hole. (3) Insert each pin terminal into its each hole. Release the Opening button to clamp the pin place.
8 Power Supply Cautions Please pay special attention to the following instructions when connecting the power cord terminals to the FP unit. • If the power supply voltage exceeds the FP unit’s specified range, connect a voltage transformer. • Between the line and the ground, be sure to use a low noise power supply. If there is still an excessive amount of noise, connect a noise reducing transformer. • Input and Output signal lines must be separated from the power control cables for operational circuits.
Item Function Color Settings Adjusts the contrast and the brightness. Screen Settings Adjusts the display position of the screen. (Analog RGB only) Custom Display Adjusts Sharpness and the backlight brightness. System Settings Changes settings such as activating the click sound. All Reset Resets the current OSD value to the default value. Input Source Switches Analog RGB and DVI-D. Auto Adjust Auto Gain Automatically adjusts the display position of the screen.
• In the OSD, pressing the button applies the set value and enables the setting. The set value won’t be canceled unless the power is turned OFF or the value is reset. If the power is turned OFF without saving the set value, that data will disappear. The last saved data will be read into the system when the FP starts. To enable the changed value, be sure to press the button.
System Settings Adjustment button Selection of the change item Click Tone Enables/disables the click sound. With this parameter, the sound level can also be adjusted. (Default value: OFF ) 720x400 Mode When an input data resolution of 720 x 400 is used in the VGA text mode, set this parameter to ON. For other resolutions, set this parameter to OFF.
All Reset Resets all the settings and then returns to the top menu. Cancels the setting and then returns to the top menu. Input Source Applies the setting and then returns to the top menu. Cancels the setting and then returns to the top menu. Auto Adjust (Analog RGB only) Applies the setting and then returns to the top menu. Cancels the setting and then returns to the top menu. • Be sure to perform the auto adjust while things except that black are shown on sides of the display.
