User Manual

ManualsBrandsProface ManualsComputer AccessoriesAPL3000B - Node Box PC

PL3000 Series Inst a llation Guide

(Built-in Battery Unit Version)

Package Contents

(1) PL Unit (1)

(2) English and Japanese Installation Guides

(one of each) <This Guide>

(3) Warning/Caution Information (1)

(4) USB Cable Clamp (2 ports) (2)

(5) USB holder (Fasteners: 1, screws: 2) (1set)

(6) Power Connector (For AC type) (1)

PL-3000B Series

(7) Installation Fasteners (Fasteners: 2,

screws: 4)

PL-3600*/3700*/3900T Series

(7) Installation Ga sket (Attached to the front

module) (1)

(8) Installation Fasteners (4 fasteners per

set)

PL-3600T Series : 1 set

PL-3600K/3700T Series : 2 sets

PL-3700K/3900T Series : 3 sets

• Be careful when install ing the PL not to

damage the built-in HDD.

This unit has been carefully packed, with

special attention to quality. However, should

you find anything damaged or missing,

please contact your local PL distributor

immediately.

When you order a PL unit built to your

specifications, that PL package should

include each optional item’s Installation

Guide. Please use that guide to check the

contents of each optional item’s package.

About the Manuals

For the detailed information on PL series,

refer to the following manuals.

• PL3000 Series Hardware Manual

• PL3000 Series Reference Manual

• PL3000 Series API Reference Manual

The manual can be downloaded from Pro-

face Home Page.

URL

http://www.pro-face.com/otasuke/

• The drivers and utilities for PL can be

downloaded from Pro-face Home Page.

Caution

Be sure to read the “Warning/Caution

Information” on the attached sheet before

using the product.

AC type

(5.08 mm [0 .2 in .] pi tc h )

Summary of content (24 pages)

PAGE 1
PL-3600*/3700*/3900T Series PL3000 Series Installation Guide (7) Installation Gasket (Attached to the front module) (1) (8) Installation Fasteners (4 fasteners per set) PL-3600T Series : 1 set PL-3600K/3700T Series : 2 sets PL-3700K/3900T Series : 3 sets (Built-in Battery Unit Version) Caution Be sure to read the “Warning/Caution Information” on the attached sheet before using the product. Package Contents • Be careful when installing the PL not to damage the built-in HDD.
PAGE 2
Part Names and Functions A C F B D E D Front (PL-3600T Series) C Name Power LED / A RAS status lamp (POWER) B Disk access lamp (DISK) BA E Front (PL-3600K Series) G Description LED Green (lit) Green (blinking) Orange (lit) Orange/Red (blinking) Not lit LED Green (lit) Not lit Orange (lit) Indicates Normal operation (power is on) Soft OFF state System monitor error (RAS error) Backlight burnout is detected.
PAGE 3
T J I D L K N H M K L D Q B H O P R I J O P Q A S VU R T S V U M Q B A N Right side (PL-3600T Series) Front (PL-3000B Series) Name Description Interface with DVI monitor or analog RGB monitor. DVI monitor can be connected to PL-3000B series only. Ethernet interface 10BASE-T/100BASE-TX/1000BASE-T Auto Changeover. This (LAN1) interface uses an RJ-45 type modular jack connector (8 pins). Ethernet interface 10BASE-T/100BASE-TX Auto Changeover.
PAGE 4
Z X Y Right side (PL-3000B Series) W V Z W X Bottom (PL-3600T Series) L a Top (PL-3600T Series) L Left side (PL-3000B Series) Bottom (PL-3000B Series) W X Y Z Fan cover System fan Power connector Power switch a Switch cover System fan inside A fan for cooling the PL unit. — — Remove switch cover when setting the DIP switch, slide switch, and replacing batteries for clock data backup.
PAGE 5
General Specifications Power Supply Electrical Specifications Input Voltage Rated Voltage Rated Frequency Allowable Frequency Range Allowable Voltage Drop Power Consumption In-Rush Current Voltage Endurance Insulation Resistance AC type AC100 to 240V AC85 to 264V 50/60Hz 47 to 63Hz 1 cycle or less (Voltage drop interval must be 1s or more.)*1 145VA or less 40A or less AC1500V 20mA for 1 minute (between charging and FG terminals) DC500V 10MΩ (min.
PAGE 6
Environmental Specifications Physical Surrounding Air 5 to 45°C Temperature Storage Temperature -20 to +60°C (when packed) 10 to 90% RH (Not condensing, wet bulb temperature: 39°C or Ambient Humidity less. Wet bulb temperature with HDD: 29°C or less.) Storage Humidity 10 to 90% RH (Not condensing, wet bulb temperature:39°C or less.
PAGE 7
• Make sure to turn off the power supply before using the switches. Adjusting the switches while power is supplied may cause errors. 1.
PAGE 8
System Set Switch Switch No. Description ON OFF Factory Settings 1 Internal setting Reserved Reserved OFF 2 Implements the logical inversion operation for RAS output Normal Close Normal Open Notes Do not change. (Factory setting) RAS output is a CLOSE state when the switch and the system is ON. When the Switch is OFF, it is the opposite. The RAS Output keeps Normal OPEN when the Soft OFF state occurs or the power turns OFF. The front USB port is available when the switch is ON.
PAGE 9
Switch No. 7 8 9 10 Description ON OFF Switches the shorting of SDA and RDA ON or OFF Switches the shorting of SDB and RDB ON or OFF Shorts SDA and RDA (RS-485 mode) Shorts SDB and RDB (RS-485 mode) RS (RTS) Automatic control mode (enabled only when RS-485 mode) The data is automatically controlled via the RS (RTS) signal. RS-232C RS-422 RS-485 No shorting (RS-422 mode) OFF OFF ON No shorting (RS-422 mode) OFF OFF ON The data is not OFF automatically controlled via the RS (RTS) signal.
PAGE 10
• When using the display unit with a cable other than FP-DV01-100 (such as FPDVD01-50), use the Factory Setting. • The default Resolution and Screen Refresh Rates are as follows. Resolution : SVGA (800x600)Screen Refresh Rate: 60Hz Maximum resolution varies depending on the FP3000 Series models. Please customize it for your FP model. 2.
PAGE 11
2. Backup Battery 1. Battery Cautions About the Battery • To prevent the battery from leakage, heat generation or explosion, be sure and: • Do not heat or throw the battery into a fire. • Do not disassemble or modify the battery. • If the battery liquid, strong alkaline, gets in your eyes, immediately rinse your eyes with clean water and consult a doctor, since it may cause you to lose your eyesight. The battery unit is equipped with a Ni-H battery for backup.
PAGE 12
• Avoid leaving the battery in high temperature places such as direct sunlight, inside a sun-heated car, near water, or near a heater. Doing so may cause battery leakage, or reduce the battery functions and lifetime. • The battery can be recycled. To recycle your used battery, follow the regulations and instructions in your area. External Interfaces • This PL unit’s serial port is not isolated.
PAGE 13
COM1 Pin # 1 RAS Interface RS-422 *3 Signal Name RDA Description • Be sure to use only the rated voltage level when using pin #1 (+12V) for external power output. Failure to do so can lead to a unit malfunction or accident.
PAGE 14
Installations 1. PL-3000B Series Installation Installation Requirements • For easier maintenance, operation, and improved ventilation, be sure to install the PL at least 50mm [1.97 in.] away from adjacent structures and other equipment. 120 mm [4.72 in.] space (minimum) is necessary at the front for cable curve. Unit:mm[in.] 50 [1.97] 50 [1.97] 50 [1.97] 50 [1.97] Horizontal mounting (Right side) Horizontal mounting (Front) 50 [1.97] 50 [1.97] 50 [1.97] 120 [4.72] 50 [1.
PAGE 15
Installation 220±0.3 [8.66±0.01] 277 [10.91] Wall mounting (2) Attach installation fasteners with the accompanying four screws (M3) to the PL unit. Pay close attention to the direction of the fasteners. The torque required to tighten these screws is 0.5 to 0.6N•m. 277 [10.91] 220±0.3 [8.66±0.01] 4-M4 [0.16] 35.5 [1.4] 4-M4 [0.16] 243 [9.57] 270 [10.63] 258±0.3 [10.16±0.01] 35.5 [1.4] • Determine the thickness of the board in consideration of its strength. The minimum thickness of a board is 1.
PAGE 16
and cabinet or enclosure’s internal temperature. • Tightening the screws with too much force can damage the PL unit. • Be sure to insert installation fasteners in the recessed portion of an installation fasteners hole. If the fasteners are not correctly attached, the PL unit may shift or fall out of the panel. 2. 50 [1.97] 30 [1.18] PL-3600*/3700*/3900T Series Installation 30 [1.18] • Be sure that heat from surrounding equipment does not cause the PL to exceed its standard operating temperature.
PAGE 17
unit without adjusting the Panel Cut size. As shown in the following diagram, simply remove 7 screws from the upper and lower positions to remove attachments from the PL-3600K series unit. (3) Insert each fastener’s hook into the slot and tighten it with a screwdriver. Tighten the screws gradually in an even, crisscross pattern. The number of the slots varies depending on the model.
PAGE 18
(2) Disconnect the flexible cable. Panel PL Flexible Cable Installation Fastener Hook Tighten against the board. • Tightening the screws with too much force can damage the PL unit. • The torque required to tighten these screws is 0.8 N•m. (3) Unscrew the four attachment screws located at the top and bottom of the front module.
PAGE 19
2. Installation/uninstallation of the front module and the control box (PL-3600K/3700*/3900T Series) (5) Lift the control box and remove the front module tabs from the slot on the installation fasteners for the control box. Then remove the control box. Uninstalling (1) Unscrew the two attachment screws to detach the cover for the flexible cable. Flexible Cable Cover (2) Disconnect the flexible cable.
PAGE 20
Power Connector Wiring The following parts are used in the power connector (plug). AC type Accompanying Power Connector CA7-ACCNL-01 of Pro-face FKC 2,5/3-STF-5,08 of Phoenix Contact When connecting the power code, use the following items when performing wiring. (Items are made by Phoenix Contact.) Recommended SZS 0.6x3.5 (1205053) Driver Shape AI 0.75-10GY(3201288) Recommended AI 1-10RD (3200182) Pin Terminals AI 1.5-10BK (3200195) AI 2.
PAGE 21
• To improve the noise resistance, be sure to twist the ends of the power cord wires before connecting them to the Power connector (Plug). • The PL unit’s power supply cord should not be bundled with or kept close to main circuit lines (high voltage, high current), or input/output signal lines. • To reduce noise, make the power cord as short as possible. • If the supplied voltage exceeds the PL unit’s range, connect a voltage transformer.
PAGE 22
to keep the clamp from interfering with nearby connectors and their cables. Connecting USB Cable Clamp Attaching the USB Cable Clamp (1) Place the PL unit face-down on a flat surface as shown below. Your PL unit has four USB connectors.
PAGE 23
Built-in battery unit and DVD unit ver- • For use on a flat surface of a Type 1 Enclosure. sion Product Model No. APL3000-BA APL3600-TA APL3700-TA APL3900-TA APL3600-KA APL3700-KA UL/c-UL Registration Model No.
PAGE 24