User Manual
Table Of Contents
- DISPOSAL OF OLD ELECTRICAL & ELECTRONIC EQUIPMENT
- SAFETY INSTRUCTIONS
- IN CASE OF FAULT
- PACKAGING, SHIPPING AND COMPLAINT
- WARRANTY AND PRODUCTS RETURN
- MAINTENANCE AND DISCLAIMER
- POWER SUPPLY
- USER’S WARNINGS AND CE CONFORMITY
- INTRODUCTION
- DESCRIPTION
- FEATURES
- WCS1000 RECEIVER UNIT
- WCS1000C and WCS1000D TRANSMITTER UNIT
- WCS1000CH BATTERY CHARGER
- IRC14430X3 Li-Ion battery pack
- SET-UP INSTRUCTIONS
- ROOM LAYOUT AND COVERAGE AREA
- WCS1000RX RECEIVER UNIT INSTALLATION
- WCS1000RX RECEIVER UNIT SET-UP
- WCS1000RX AUDIO RF CHANNEL SET-UP
- WCS1000C and WCS1000D INSTALL OR REPLACE THE BATTERY PACK
- WCS1000C and WCS1000D MICROPHONE INSTALLATION
- WCS1000C and WCS1000D TRANSMITTER UNIT SET-UP
- CONFERENCE SYSTEM AUDIO CHECK
- WCS1000RX LOCK & UNLOCK
- TECHNICAL SPECIFICATION
- TRATTAMENTO DEL DISPOSITIVO ELETTRICO OD ELETTRONICO A FINE VITA
- AVVERTENZE PER LA SICUREZZA
- IN CASO DI GUASTO
- IMBALLAGGIO, TRASPORTO E RECLAMI
- GARANZIE E RESI
- MANUTENZIONE E LIMITAZIONI D’USO
- ALIMENTAZIONE
- AVVERTENZE PER L’UTILIZZO E CONFORMITÀ CE
- INTRODUZIONE
- DESCRIZIONE
- FEATURES
- WCS1000 UNITÀ RICEVITORE
- WCS1000C e WCS1000D UNITÀ TRASMETTITORE
- WCS1000CH CARICA BATTERIE
- IRC14430X3 pacco batteria Li-Ion
- ISTRUZIONI DI IMPOSTAZIONE
- DISPOSIZIONE IN AMBIENTE E AREA DI COPERTURA
- INSTALLAZIONE DEL RICEVITORE WCS1000RX
- CONFIGURAZIONE DEL RICEVITORE WCS1000RX
- IMPOSTAZIONE DEI CANALI AUDIO RF SU WCS1000RX
- INSTALLARE O SOSTITUIRE LE BATTERIE SU WCS1000C/D
- INSTALLAZIONE DEL MICROFONO SU WCS1000C/D
- IMPOSTAZIONE DELLE UNITÀ TRASMETTITORE WCS1000C/D
- CONTROLLO AUDIO DEL SISTEMA PER CONFERENZA
- BLOCCO E SBLOCCO DEL WCS1000RX
- SPECIFICHE TECNICHE
- FIG.1
- FIG.2
- FIG.3
- FIG.4
9
8. DISPLAY
The Display shows current mode status, room number, unit number, channel number, volume setting,
battery status:
9. POWER button
To turn on the unit press and hold this button until the display appears: if that doesn’t happen, replace
the battery pack with a new one fully charged.
To turn off the unit press and hold again the button until the display shows:
.
If the MUTE/SET button is held down when the unit is switched on, then it enters in setting mode (see
set-up instructions).
If the UP button is held down when the unit is switched on, the transmitter operates as FREE from the
receiving unit: this mode is usually selected only for servicing operation. In order to set back the standard
LINK operation turn the unit off and on again.
WCS1000CH BATTERY CHARGER
See FIG. 3 at page 38.
The battery charger operates with an universal input voltage (100V-240V~) and it can charge up to 16 lithium
battery packs (use only the IRC14430X3 type supplied with the microphone units). Its internal intelligent
charging management circuit protects Li-Ion batteries from excessive temperature and charging. It is hosted
in a case with extendable handle and castors for easy transport.
1. CHARGE LED
This is the charging status LED: it is RED during the battery pack charging, it is GREEN when the battery
pack is fully charged and ready to be installed in the transmitter.
2. BATTERY HOLDER
Insert the battery pack to be recharged in any holder. Be sure to insert it respecting the right polarity. A
fully discharged pack requires about 2h to be fully recharged.
3. POWER INDICATOR
It’s on when the charger is active.
4. POWER ON/OFF SWITCH
To turn on and off the charger.
5. AC~ SOCKET
Here’s where you plug in your mains supply cord. Be sure that your device is turned off before you plug
the mains supply cord into an electrical outlet.
IRC14430X3 Li-Ion battery pack
See FIG. 4 at page 38.
The supplied Li-Ion battery pack features an excellent safety performance, lightweight, high capacity ratio