User Manual
Table Of Contents
- DISPOSAL OF OLD ELECTRICAL & ELECTRONIC EQUIPMENT
- SAFETY INSTRUCTIONS
- IN CASE OF FAULT
- PACKAGING, SHIPPING AND COMPLAINT
- WARRANTY AND PRODUCTS RETURN
- MAINTENANCE AND DISCLAIMER
- POWER SUPPLY
- USER’S WARNINGS AND CE CONFORMITY
- INTRODUCTION
- DESCRIPTION
- FEATURES
- WCS1000 RECEIVER UNIT
- WCS1000C and WCS1000D TRANSMITTER UNIT
- WCS1000CH BATTERY CHARGER
- IRC14430X3 Li-Ion battery pack
- SET-UP INSTRUCTIONS
- ROOM LAYOUT AND COVERAGE AREA
- WCS1000RX RECEIVER UNIT INSTALLATION
- WCS1000RX RECEIVER UNIT SET-UP
- WCS1000RX AUDIO RF CHANNEL SET-UP
- WCS1000C and WCS1000D INSTALL OR REPLACE THE BATTERY PACK
- WCS1000C and WCS1000D MICROPHONE INSTALLATION
- WCS1000C and WCS1000D TRANSMITTER UNIT SET-UP
- CONFERENCE SYSTEM AUDIO CHECK
- WCS1000RX LOCK & UNLOCK
- TECHNICAL SPECIFICATION
- TRATTAMENTO DEL DISPOSITIVO ELETTRICO OD ELETTRONICO A FINE VITA
- AVVERTENZE PER LA SICUREZZA
- IN CASO DI GUASTO
- IMBALLAGGIO, TRASPORTO E RECLAMI
- GARANZIE E RESI
- MANUTENZIONE E LIMITAZIONI D’USO
- ALIMENTAZIONE
- AVVERTENZE PER L’UTILIZZO E CONFORMITÀ CE
- INTRODUZIONE
- DESCRIZIONE
- FEATURES
- WCS1000 UNITÀ RICEVITORE
- WCS1000C e WCS1000D UNITÀ TRASMETTITORE
- WCS1000CH CARICA BATTERIE
- IRC14430X3 pacco batteria Li-Ion
- ISTRUZIONI DI IMPOSTAZIONE
- DISPOSIZIONE IN AMBIENTE E AREA DI COPERTURA
- INSTALLAZIONE DEL RICEVITORE WCS1000RX
- CONFIGURAZIONE DEL RICEVITORE WCS1000RX
- IMPOSTAZIONE DEI CANALI AUDIO RF SU WCS1000RX
- INSTALLARE O SOSTITUIRE LE BATTERIE SU WCS1000C/D
- INSTALLAZIONE DEL MICROFONO SU WCS1000C/D
- IMPOSTAZIONE DELLE UNITÀ TRASMETTITORE WCS1000C/D
- CONTROLLO AUDIO DEL SISTEMA PER CONFERENZA
- BLOCCO E SBLOCCO DEL WCS1000RX
- SPECIFICHE TECNICHE
- FIG.1
- FIG.2
- FIG.3
- FIG.4
15
WCS1000C and WCS1000D MICROPHONE INSTALLATION
To install the microphone gooseneck into the base, insert it to the base connector, then turn it until it slides
slightly into the connector. When it is inserted completely (be careful to not force it!), screw the security ring
clockwise:
To remove the gooseneck unscrew the security ring before disconnecting.
WCS1000C and WCS1000D TRANSMITTER UNIT SET-UP
Press the POWER button to switch the microphone unit while keeping pressed the MUTE button: the
microphone unit enters in SETTING mode with the first parameter flashing. You can select the next
parameter by pressing again the MUTE button and you change a parameter value using the and
buttons. If you press again POWER button or wait 9 secs the microphone unit will exit from setting mode.
The parameter are:
This is the room control channel in the range of 0-9,A-F. Each channel corresponds to a frequency and
you must set the same frequency channel previously set on the WCS1000RX receiver.
The receiver and all the transmitter units of the same conference system must be set always on
the same Control Room Channel.
Chairman microphone unit ID setting: this number can be set from 0-9, A-F for a total 16 ID
chairman units in the system. However, in a typical conference system there is only one chairman.
Delegate microphone unit ID setting: this number can be set from 0-255, for a maximum
256 ID different delegate units in the conference system.
All microphone ID in one system must be different: if different units have the same ID number,
the system will not work properly.
Chime of chairman microphone: when the chairman presses the PRIORITY button, the system playa a
chime sound to advise all delegates that he/she is taking the word. Setting this parameter as
no chime
sound is played.