User Manual
Table Of Contents
- DISPOSAL OF OLD ELECTRICAL & ELECTRONIC EQUIPMENT
- SAFETY INSTRUCTIONS
- IN CASE OF FAULT
- PACKAGING, SHIPPING AND COMPLAINT
- WARRANTY AND PRODUCTS RETURN
- MAINTENANCE AND DISCLAIMER
- POWER SUPPLY
- USER’S WARNINGS AND CE CONFORMITY
- INTRODUCTION
- DESCRIPTION
- FEATURES
- WCS1000 RECEIVER UNIT
- WCS1000C and WCS1000D TRANSMITTER UNIT
- WCS1000CH BATTERY CHARGER
- IRC14430X3 Li-Ion battery pack
- SET-UP INSTRUCTIONS
- ROOM LAYOUT AND COVERAGE AREA
- WCS1000RX RECEIVER UNIT INSTALLATION
- WCS1000RX RECEIVER UNIT SET-UP
- WCS1000RX AUDIO RF CHANNEL SET-UP
- WCS1000C and WCS1000D INSTALL OR REPLACE THE BATTERY PACK
- WCS1000C and WCS1000D MICROPHONE INSTALLATION
- WCS1000C and WCS1000D TRANSMITTER UNIT SET-UP
- CONFERENCE SYSTEM AUDIO CHECK
- WCS1000RX LOCK & UNLOCK
- TECHNICAL SPECIFICATION
- TRATTAMENTO DEL DISPOSITIVO ELETTRICO OD ELETTRONICO A FINE VITA
- AVVERTENZE PER LA SICUREZZA
- IN CASO DI GUASTO
- IMBALLAGGIO, TRASPORTO E RECLAMI
- GARANZIE E RESI
- MANUTENZIONE E LIMITAZIONI D’USO
- ALIMENTAZIONE
- AVVERTENZE PER L’UTILIZZO E CONFORMITÀ CE
- INTRODUZIONE
- DESCRIZIONE
- FEATURES
- WCS1000 UNITÀ RICEVITORE
- WCS1000C e WCS1000D UNITÀ TRASMETTITORE
- WCS1000CH CARICA BATTERIE
- IRC14430X3 pacco batteria Li-Ion
- ISTRUZIONI DI IMPOSTAZIONE
- DISPOSIZIONE IN AMBIENTE E AREA DI COPERTURA
- INSTALLAZIONE DEL RICEVITORE WCS1000RX
- CONFIGURAZIONE DEL RICEVITORE WCS1000RX
- IMPOSTAZIONE DEI CANALI AUDIO RF SU WCS1000RX
- INSTALLARE O SOSTITUIRE LE BATTERIE SU WCS1000C/D
- INSTALLAZIONE DEL MICROFONO SU WCS1000C/D
- IMPOSTAZIONE DELLE UNITÀ TRASMETTITORE WCS1000C/D
- CONTROLLO AUDIO DEL SISTEMA PER CONFERENZA
- BLOCCO E SBLOCCO DEL WCS1000RX
- SPECIFICHE TECNICHE
- FIG.1
- FIG.2
- FIG.3
- FIG.4
14
In order to select the correct frequency for each channel and to avoid interferences, we suggest to use the
following procedure:
1) Set the first delegate channel in the receiver unit. Then switch on the first delegate microphone and
press the TALK button, leaving the unit active.
2) Set the second delegate channel in the receiver unit. Then switch on the second delegate
microphone and press TALK button, leaving the unit active.
3) Repeat the procedure for delegate channel three and four.
TIP: if there are other radio-frequency transmitters in the same coverage area where the WCS1000
system is used, we suggest to turn them on when setting the RF channels using auto-scan, so the
system will choose frequencies that are truly free.
IMPORTANT NOTE: the transmitting channels are set on the receiver unit only. The WCS1000RX
manages the RF channels and tell to the chairman and delegate units which RF channel they have
to use. To do that WCS1000RX uses the room control channel and this is why it’s so important that
the room control channel is the same for all units. See above about how to set the room control
channel on WCS1000RX, further in the manual you can see how to set it on transmitter units.
WCS1000C and WCS1000D INSTALL OR REPLACE THE BATTERY PACK
When the display on WCS1000C or WCS1000D units shows a low battery level or when the battery pack is
completely exhausted, replace the battery pack as follows:
IMPORTANT: be careful to respect always the polarity marked inside the battery inlet.
Remove the batteries if you don’t use the microphone for a long period of time: this will avoid the
corrosion of the battery contacts.