User Manual
Table Of Contents
- DISPOSAL OF OLD ELECTRICAL & ELECTRONIC EQUIPMENT
- SAFETY INSTRUCTIONS
- IN CASE OF FAULT
- PACKAGING, SHIPPING AND COMPLAINT
- WARRANTY AND PRODUCTS RETURN
- MAINTENANCE AND DISCLAIMER
- POWER SUPPLY
- USER’S WARNINGS AND CE CONFORMITY
- INTRODUCTION
- DESCRIPTION
- FEATURES
- WCS1000 RECEIVER UNIT
- WCS1000C and WCS1000D TRANSMITTER UNIT
- WCS1000CH BATTERY CHARGER
- IRC14430X3 Li-Ion battery pack
- SET-UP INSTRUCTIONS
- ROOM LAYOUT AND COVERAGE AREA
- WCS1000RX RECEIVER UNIT INSTALLATION
- WCS1000RX RECEIVER UNIT SET-UP
- WCS1000RX AUDIO RF CHANNEL SET-UP
- WCS1000C and WCS1000D INSTALL OR REPLACE THE BATTERY PACK
- WCS1000C and WCS1000D MICROPHONE INSTALLATION
- WCS1000C and WCS1000D TRANSMITTER UNIT SET-UP
- CONFERENCE SYSTEM AUDIO CHECK
- WCS1000RX LOCK & UNLOCK
- TECHNICAL SPECIFICATION
- TRATTAMENTO DEL DISPOSITIVO ELETTRICO OD ELETTRONICO A FINE VITA
- AVVERTENZE PER LA SICUREZZA
- IN CASO DI GUASTO
- IMBALLAGGIO, TRASPORTO E RECLAMI
- GARANZIE E RESI
- MANUTENZIONE E LIMITAZIONI D’USO
- ALIMENTAZIONE
- AVVERTENZE PER L’UTILIZZO E CONFORMITÀ CE
- INTRODUZIONE
- DESCRIZIONE
- FEATURES
- WCS1000 UNITÀ RICEVITORE
- WCS1000C e WCS1000D UNITÀ TRASMETTITORE
- WCS1000CH CARICA BATTERIE
- IRC14430X3 pacco batteria Li-Ion
- ISTRUZIONI DI IMPOSTAZIONE
- DISPOSIZIONE IN AMBIENTE E AREA DI COPERTURA
- INSTALLAZIONE DEL RICEVITORE WCS1000RX
- CONFIGURAZIONE DEL RICEVITORE WCS1000RX
- IMPOSTAZIONE DEI CANALI AUDIO RF SU WCS1000RX
- INSTALLARE O SOSTITUIRE LE BATTERIE SU WCS1000C/D
- INSTALLAZIONE DEL MICROFONO SU WCS1000C/D
- IMPOSTAZIONE DELLE UNITÀ TRASMETTITORE WCS1000C/D
- CONTROLLO AUDIO DEL SISTEMA PER CONFERENZA
- BLOCCO E SBLOCCO DEL WCS1000RX
- SPECIFICHE TECNICHE
- FIG.1
- FIG.2
- FIG.3
- FIG.4
12
Pressing again the SET button the display shows the Delegate RF activation setting:
Pressing the UP and DOWN buttons you can enable [1] or disable [0] a delegate unit RF channel. Pressing
again the SET button you can also select RF channels D2 or D3. D4 cannot be disabled because at least one
channel must be active.
TIP: this function is useful to reduce the number of delegate RF channels that can be active
simultaneously. For example, in case of two adjacent meeting rooms using two WCS1000 system, if
you reduce the active channels of both systems to two each they can both operate in a more
reliable way.
NOTE: regardless of how many RF channels are active, the maximum number of delegate units that
can be used in a WCS1000 system is always 256, see also the delegates set-up operation further in
this manual.
Pressing again the SET button the display shows the Test setting:
This is a FACTORY mode used for the device test.
Pressing again the POWER button the receiver will be initialized and enter the STANDARD operating mode:
The display will show the last set-up status (the following is an example):
This is the STANDARD menu and the most used parameters can be set here.
Pressing the SET button one time is possible to set the CHAIRMAN PRIORITY MODE: by pressing UP or
DOWN button you can select CFREE or CONLY.
: in this mode, when the chairman presses the PRIORITY button all delegates are shut down and
he has the priority to speak, but any delegate can speak again together with the chairman just by pressing his
TALK button.