User Manual
Table Of Contents
- DISPOSAL OF OLD ELECTRICAL & ELECTRONIC EQUIPMENT
- SAFETY INSTRUCTIONS
- IN CASE OF FAULT
- PACKAGING, SHIPPING AND COMPLAINT
- WARRANTY AND PRODUCTS RETURN
- MAINTENANCE AND DISCLAIMER
- POWER SUPPLY
- USER’S WARNINGS AND CE CONFORMITY
- INTRODUCTION
- DESCRIPTION
- FEATURES
- WCS1000 RECEIVER UNIT
- WCS1000C and WCS1000D TRANSMITTER UNIT
- WCS1000CH BATTERY CHARGER
- IRC14430X3 Li-Ion battery pack
- SET-UP INSTRUCTIONS
- ROOM LAYOUT AND COVERAGE AREA
- WCS1000RX RECEIVER UNIT INSTALLATION
- WCS1000RX RECEIVER UNIT SET-UP
- WCS1000RX AUDIO RF CHANNEL SET-UP
- WCS1000C and WCS1000D INSTALL OR REPLACE THE BATTERY PACK
- WCS1000C and WCS1000D MICROPHONE INSTALLATION
- WCS1000C and WCS1000D TRANSMITTER UNIT SET-UP
- CONFERENCE SYSTEM AUDIO CHECK
- WCS1000RX LOCK & UNLOCK
- TECHNICAL SPECIFICATION
- TRATTAMENTO DEL DISPOSITIVO ELETTRICO OD ELETTRONICO A FINE VITA
- AVVERTENZE PER LA SICUREZZA
- IN CASO DI GUASTO
- IMBALLAGGIO, TRASPORTO E RECLAMI
- GARANZIE E RESI
- MANUTENZIONE E LIMITAZIONI D’USO
- ALIMENTAZIONE
- AVVERTENZE PER L’UTILIZZO E CONFORMITÀ CE
- INTRODUZIONE
- DESCRIZIONE
- FEATURES
- WCS1000 UNITÀ RICEVITORE
- WCS1000C e WCS1000D UNITÀ TRASMETTITORE
- WCS1000CH CARICA BATTERIE
- IRC14430X3 pacco batteria Li-Ion
- ISTRUZIONI DI IMPOSTAZIONE
- DISPOSIZIONE IN AMBIENTE E AREA DI COPERTURA
- INSTALLAZIONE DEL RICEVITORE WCS1000RX
- CONFIGURAZIONE DEL RICEVITORE WCS1000RX
- IMPOSTAZIONE DEI CANALI AUDIO RF SU WCS1000RX
- INSTALLARE O SOSTITUIRE LE BATTERIE SU WCS1000C/D
- INSTALLAZIONE DEL MICROFONO SU WCS1000C/D
- IMPOSTAZIONE DELLE UNITÀ TRASMETTITORE WCS1000C/D
- CONTROLLO AUDIO DEL SISTEMA PER CONFERENZA
- BLOCCO E SBLOCCO DEL WCS1000RX
- SPECIFICHE TECNICHE
- FIG.1
- FIG.2
- FIG.3
- FIG.4
11
IMPORTANT: the different receiver antennas must be connected in correct positions or the system
will work properly.
WCS1000RX RECEIVER UNIT SET-UP
WCS1000RX receiver’s most used parameters can be set in the STANDARD menu, while more in-deep
parameters can be set in the SYSTEM SETTING menu.
To visualize the SYSTEM SETTING menu press and hold the SET button while powering up the receiver. The
display will show:
Release the SET button and the display will show the Room setting:
Pressing the UP and DOWN buttons you can choose the Room control channel within the range of 0-9,
A-F. This is the RF channel used by the system to exchange control data between the receiver and the
microphone units. Each channel corresponds to a frequency and a free frequency channel must be selected.
When choosing a control channel try to avoid channels used by other RF apparatus or other
WCS1000 systems in adjacent rooms.
The receiver and all the transmitter units must be set always on the same room CONTROL
channel.
In the majority of the UE countries the range for remote controls SRD is 433.050-434.790 MHz,
that corresponds to the Room channels B and C. In any case please consult your national
spectrum authority to set a proper frequency channel.