User Manual
Table Of Contents
- DISPOSAL OF OLD ELECTRICAL & ELECTRONIC EQUIPMENT
- GENERAL SAFETY INSTRUCTIONS
- IN CASE OF FAULT
- PACKAGING, SHIPPING AND COMPLAINT
- WARRANTY AND PRODUCTS RETURN
- MAINTENANCE AND DISCLAIMER
- POWER SUPPLY
- CONFORMITY
- INTRODUCTION
- DESCRIPTION
- INSTRUCTIONS
- 1. MIC-XLR / LINE-JACK combo input (ch. 1 ÷ 8)
- 2. LO CUT switch (ch. 1 ÷ 8)
- 3. CHANNEL GAIN control (ch. 1 ÷ 8 / 9 ÷ 16)
- 4. COMP compressor control (ch. 1 ÷ 8)
- 5. COMP indicator (ch. 1 ÷ 8)
- 6. EQ section HIGH control (ch. 1 ÷ 8 / 9 ÷ 16)
- 7. EQ section MID LEVEL control (ch. 1 ÷ 8)
- 8. EQ section FREQ control (ch. 1 ÷ 8)
- 9. EQ section LOW control (ch. 1 ÷ 8 / 9 ÷ 16)
- 10. AUX 1 control (pre) (ch. 1 ÷ 8 / 9 ÷ 16)
- 11. AUX 2 control (pre) (ch. 1 ÷ 8 / 9 ÷ 16)
- 12. AUX 3 send control (pre/post) (ch. 1 ÷ 8 / 9 ÷ 16)
- 13. POST switch (ch. 1 ÷ 8 / 9 ÷ 16)
- 14. AUX4/FX send control (ch. 1 ÷ 8 / 9 ÷ 16)
- 15. PAN control (ch. 1 ÷ 8)
- 16. MUTE switch/LED (ch. 1 ÷ 8 / 9 ÷ 16)
- 17. MIX switch (ch. 1 ÷ 8 / 9 ÷ 16)
- 18. 1-2 switch (ch. 1 ÷ 8 / 9 ÷ 16)
- 19. PEAK/PFL detector (ch. 1 ÷ 8 / 9 ÷ 16)
- 20. PFL switch (ch. 1 ÷ 8 / 9 ÷ 16)
- 21. CHANNEL FADER level control (ch. 1 ÷ 8 / 9 ÷ 16)
- 22. MIC-XLR / LINE-JACK L MONO combo input (ch. 9 ÷ 16)
- 23. LINE-JACK R Input (ch. 10 / 12 / 14 / 16)
- 24. EQ section MID control (ch. 9 ÷ 16)
- 25. BAL control (ch. 9 ÷ 16)
- 26. FX PRESETS selector
- 27. FX DISPLAY number
- 28. EFFECT MUTE button
- 29. FX MUTE pedal jack input
- 30. EFFECT PEAK/MUTE detector
- 31. FX FADER level control
- 32. 2TRK inputs
- 33. USB/2TRK IN level control
- 34. MIX - CH15/16 switch
- 35. USB/2TRK OUT level control
- 36. 2 TRK OUT PEAK detector
- 37. MIX - AUX 1-2 switch
- 38. 2TRK outputs
- 39. AUX 1 SEND level control
- 40. AUX 1 SEND jack output
- 41. AUX 2 SEND level control
- 42. AUX 2 SEND jack output
- 43. AUX 3 SEND level control
- 44. AUX 3 SEND jack output
- 45. AUX 4 / FX SEND level control
- 46. AUX 4 SEND jack output
- 47. GROUPS 1-2 FADER level control
- 48. GROUPS 1-2 jack output
- 49. GROUP TO MIX switch
- 50. MAIN MIX to C.ROOM switch
- 51. GROUP 1-2 to C.ROOM switch
- 52. 2TRK to C.ROOM switch
- 53. PHONES level control
- 54. PHONES stereo jack output
- 55. C.ROOM level control
- 56. C.ROOM L & R jack output
- 57. PFL ACTIVE LED
- 58. L & R LEVEL meters
- 59. MAIN MIX FADER level control
- 60. MAIN MIX L & R XLR output balanced
- 61. MAIN MIX L & R jack output balanced
- 62. +48V phantom switch and LED
- 63. ON LED
- 64. USB PORT socket
- 65. POWER switch
- 66. AC~ socket
- 67. FUSE holder
- TECHNICAL SPECIFICATION
- TRATTAMENTO DEL DISPOSITIVO ELETTRICO OD ELETTRONICO A FINE VITA
- AVVERTENZE PER LA SICUREZZA
- IN CASO DI GUASTO
- IMBALLAGGIO, TRASPORTO E RECLAMI
- GARANZIE E RESI
- MANUTENZIONE E LIMITAZIONI D’USO
- ALIMENTAZIONE
- CONFORMITÀ CE
- INTRODUZIONE
- DESCRIZIONE
- ISTRUZIONI
- 1. MIC-XLR / LINE-JACK ingresso combo (c. 1 ÷ 8)
- 2. LO CUT filtro elimina bassi (c. 1 ÷ 8)
- 3. GAIN controllo guadagno (c. 1 ÷ 8 / 9 ÷ 16)
- 4. COMP controllo compressore (c. 1 ÷ 8)
- 5. COMP indicatore compressione attiva (c. 1 ÷ 8)
- 6. EQ HI equalizzatore controllo alti (c. 1 ÷ 8 / 9 ÷ 16)
- 7. EQ MID eq. controllo intensità medi (c. 1 ÷ 8)
- 8. EQ FREQ eq. controllo frequenza medi (c. 1 ÷ 8)
- 9. EQ LOW equalizzatore controllo bassi (c. 1 ÷ 8 / 9 ÷ 16)
- 10. AUX 1 controllo mandata pre-fader (c. 1 ÷ 8 / 9 ÷ 16)
- 11. AUX 2 controllo mandata pre-fader (c. 1 ÷ 8 / 9 ÷ 16)
- 12. AUX 3 controllo mandata pre-fader (c. 1 ÷ 8 / 9 ÷ 16)
- 13. POST tasto post fader (c. 1 ÷ 8 / 9 ÷ 16)
- 14. AUX4/FX controllo mandata (c. 1 ÷ 8 / 9 ÷ 16)
- 15. PAN controllo panoramico (c. 1 ÷ 8 / 9 ÷ 16)
- 16. MUTE tasto/LED (c. 1 ÷ 8 / 9 ÷ 16)
- 17. MIX tasto assegnazione al MAIN MIX (c. 1 ÷ 8 / 9 ÷ 16)
- 18. 1-2 tasto assegnazione a GROUPS 1-2 (c. 1 ÷ 8 / 9 ÷ 16)
- 19. PEAK/PFL rilevatore di picco e PFL (c. 1 ÷ 8 / 9 ÷ 16)
- 20. PFL tasto attivazione preascolto (c. 1 ÷ 8 / 9 ÷ 16)
- 21. FADER LEVEL controllo di livello del canale (c. 1 ÷ 8 / 9 ÷ 16)
- 22. MIC-XLR / LINE-JACK L MONO ingresso combo (c. 9 ÷ 16)
- 23. LINE R ingresso linea (c. 9 ÷ 16)
- 24. EQ MID equalizzatore controllo medi (c. 9 ÷ 16)
- 25. BAL controllo bilanciamento (c. 9 ÷ 16)
- 26. PRESETS selettore effetto
- 27. FX DISPLAY number
- 28. MUTE tasto per silenziare l'effetto
- 29. FX MUTE ingresso jack per pedale
- 30. PEAK/MUTE LED rilevatore di picco e mute
- 31. FX FADER controllo livello effetto
- 32. 2TRK IN ingressi RCA stereo
- 33. USB / 2TRK IN LEVEL controllo di livello
- 34. MIX / CH15/16 tasto assegnazione USB/2TRK IN
- 35. USB / 2TRK OUT LEVEL controllo di livello
- 36. PEAK rilevatore di picco uscita USB/2TRK OUT
- 37. MIX - AUX 1-2 assegnazione USB/2TRK OUT
- 38. 2TRK OUT uscite RCA stereo
- 39. AUX 1 SEND livello uscita ausiliario 1
- 40. AUX SEND 1 uscita jack ausiliaria 1
- 41. AUX 2 SEND livello uscita ausiliario 2
- 42. AUX SEND 2 uscita jack ausiliaria 2
- 43. AUX 3 SEND livello uscita ausiliario 3
- 44. AUX SEND 3 uscita jack ausiliaria 3
- 45. AUX 4 / FX SEND livello uscita AUX4 e ingresso FX
- 46. AUX 4 SEND uscita jack ausiliaria 4
- 47. GROUPS 1-2 FADER controllo livello uscite GROUPS 1-2
- 48. GROUPS 1-2 jack di uscita
- 49. GROUP TO MIX tasto assegnazione GROUPS 1-2 al MIX
- 50. MAIN MIX a C.ROOM selettore MAIN MIX
- 51. GROUP 1-2 a C.ROOM selettore GROUPS 1-2
- 52. USB/2TRK a C.ROOM selettore USB/2TRK IN
- 53. PHONES livello uscita cuffia
- 54. PHONES uscita jack stereo per cuffia
- 55. C.ROOM livello uscita
- 56. C.ROOM L & R uscite jack control room
- 57. PFL ACTIVE LED indicatore PFL attivo
- 58. L & R LEVEL METERS indicatori di livello
- 59. MAIN MIX livello uscita MIX
- 60. MAIN MIX L & R uscite XLR bilanciate
- 61. MAIN MIX L & R uscite jack bilanciate
- 62. +48V interruttore e LED alimentazione phantom
- 63. ON indicatore LED acceso/spento
- 64. USB PORT (presa USB)
- 65. POWER interruttore di accensione
- 66. AC~ presa di alimentazione di rete
- 67. FUSE portafusibili
- SPECIFICHE TECNICHE
- Mechanical Dimensions – Dimensioni Meccaniche
- Configurations Example – Esempio Configurazioni
- Accessories – Accessori
- Connectors - Connettori
6
INTRODUCTION
Thank you for choosing this PROEL product and for your trust in our brand, synonymous of professionalism,
accuracy, high quality and reliability. All our products are CE approved and designed for continuous use in
professional applications.
DESCRIPTION
MQ is a series of mixers created by PROEL to offer in a very compact and stylish package a high input density,
a full set of features and a superior audio quality, at a very convenient price point. The MQ series includes 5
models with 6, 10, 12 and 16 inputs, able to satisfy most of the sound reinforcement applications. Carefully
designed and engineered in Italy by PROEL R&D, MQ mixers are hosted in ultra-rugged cases, providing
extended durability for a stage-proof use.
The smallest models of the series, MQ6 and MQ6FX, offer in an ultra-compact format the performance of
professional consoles, delivering a clean and accurate sound. The MQ6FX, despite its small size, includes a
high-quality 24-bit DSP able to provide musicians and performers with studio-grade effects.
MQ10FX, together with 3-band EQ and one-knob intelligent COMPRESSORS, offers also 100 DSP presets with
a convenient LED display for the selection.
MQ12USB additional features include an USB audio I/O interface and extended mixing capability with
MONITOR send, STEREO GROUP bus and 45mm control faders.
The top-of-the-line MQ16USB feature 16 inputs and 12 microphone channels together with sweep mids and
one-knob intelligent COMPRESSORS on mono channels, 4 AUX sends, STEREO GROUP bus and 60mm control
faders.
Optional padded carrying bags and metal brackets for 19” rack mounting are available for selected models.
INSTRUCTIONS
1. MIC-XLR / LINE-JACK combo input (ch. 1 ÷ 8)
This is a female MIC-XLR / LINE-JACK combo connector that accepts a balanced microphone XLR input from
almost any type of microphone, or a balanced or unbalanced line level JACK input signal from almost any line
source.
The MIC-XLR input is wired as follows:
Pin 1 = shield or ground
Pin 2 = + positive or "hot"
Pin 3 = - negative or "cold"
The LINE-JACK input is wired as follows:
Tip = + positive or "hot"
Ring = - negative or "cold"
Sleeve = shield or ground
When connecting an unbalanced signal, wire them as follows:
Pin2 / Tip = + positive or "hot"
Pin 1-3 / Sleeve = shield or ground