Product manual

destination -- Displays information about the receiver/collector/management-station to
which the sampling-polling data is sent. (p. 467)
■
■ sampling-polling -- Displays information about sampling and polling. (p. 506)
■ port-list -- Displays information about sampling and polling. ([ethernet] PORT-LIST) (p.
496)
■ show snmp-server -- Display information on all SNMP communities, trap receivers and Snmp
response/trap source-ip policy configured on the switch (p. 508)
■ community -- Specify SNMP community to which to restrict the output. (ASCII-STR) (p. 461)
■ traps -- Show all configured traps. (p. 515)
■ show snmpv3 -- Show configuration of SNMPv3 features. (p. 508)
■ access-rights -- Show information about access rights. (p. 452)
■ group < ManagerPriv | ManagerAuth | OperatorAuth | ... > -- Show SNMPv3 users. (p. 473)
■ sec-model -- Set security model. (p. 506)
■ ver1-2c < ver1 | ver2c > -- Configure SNMPv3 User entry. (p. 516)
■ ver3 -- SNMP version 3 security model. (p. 517)
■ ver3 < noauth | auth | priv > -- Set security level. (p. 517)
■ community -- Show SNMPv3 Community table. (p. 461)
■ COMMUNITY-NAME -- Show a specific community entry. (ASCII-STR) (p. 461)
■ enable -- Show SNMPv3 status. (p. 470)
■ engineid -- Show switch's SNMP engineId. (p. 470)
■ group -- Show SNMPv3 User to Group mappings. (p. 473)
■ group < ManagerPriv | ManagerAuth | OperatorAuth | ... > -- Show SNMPv3 users. (p. 473)
■ user -- Show a specific user. (ASCII-STR) (p. 516)
■ sec-model < ver1 | ver2c | ver3 > -- Show a specific security model. (p. 506)
■ notify -- Show SNMPv3 notification table. (p. 493)
■ NOTIFY-NAME -- Show a specific notification entry. (ASCII-STR) (p. 493)
■ only -- Show SNMP message reception policy. (p. 493)
■ params -- Show SNMPv3 Target Parameters table. (p. 494)
■ PARAM-NAME -- Show a specific Target Parameter entry. (ASCII-STR) (p. 494)
■ restricted-access -- Show SNMPv1 and SNMPv2c access properties. (p. 503)
■ targetaddress -- Show SNMPv3 Target Address table. (p. 513)
■ TARGETADDR-NAME -- Show a specifc target address entry. (ASCII-STR) (p. 513)
■ user -- Show SNMPv3 users. (p. 516)
■ USER-NAME -- Show a specific user. (ASCII-STR) (p. 516)
■ view -- Show views. (p. 517)
■ VIEW-NAME -- Set view name. (ASCII-STR) (p. 517)
■ SUB-TREE -- Set the OID of the tree. (ASCII-STR) (p. 512)
■ show sntp -- Show configured time protocol and servers (p. 508)
■ show spanning-tree -- Show spanning tree information (p. 509)
■ bpdu-protection -- Show spanning tree BPDU protection status information. (p. 458)
■ port-list -- Limit the port information printed to the set of the specified ports. ([ethernet]
PORT-LIST) (p. 496)
■ config -- Show spanning tree configuration information. (p. 462)
■ instance -- Show the spanning tree instance information. (p. 477)
■ ist -- Show the information for the internal spanning tree (IST) instance. (p. 483)
■ MSTID < 1 to 16 > -- Spanning tree instance ID for which to show the information. (p.
491)
■ debug-counters -- Show spanning tree debug counters information. (p. 467)
■ instance < 0 to 16 > -- Show spanning tree instance debug counters information. (NUMBER)
(p. 477)
■ ports -- Show spanning tree port(s) debug counters information. ([ethernet] PORT-LIST)
(p. 498)
445© 2008 Hewlett-Packard Development Company, L.P.
showCommand Line Interface Reference Guide