Product manual

ManualsBrandsProCurve ManualsComputer equipment8212zl

441

442

443

444

445

446

447

448

449

450

■ interface -- Show OSPF interfaces' information (p. 479)

■ if-ip -- Specify IP address of the interface for which to show detailed information.

(IP-ADDR) (p. 476)

■ vlan -- Specify VLAN of the interface for which to show detailed information. (VLAN-ID)

(p. 518)

■ link-state -- Show all Link State Advertisements from throughout the areas to which the

device is attached (p. 485)

■ advertise -- Show each LSA as a stream of bytes in hexadecimal notation. (p. 452)

■ area-id -- Show LSAs for the specified area only. (OSPF-AREA-ID) (p. 454)

■ link-state-id -- Show LSAs with the specified ID only. (IP-ADDR) (p. 485)

■ router-id -- Show LSAs with the specified Router ID only. (IP-ADDR) (p. 505)

■ sequence-number -- Show LSAs with the specified sequence number only. (p. 506)

■ status -- The keyword is optional and can be omitted. (p. 511)

■ type < router | network | summary | ... > -- Show LSAs of the specified type only. (p.

515)

■ neighbor -- Show all OSPF neighbors in the locality of of the device (p. 492)

■ neighbor-ip -- (IP-ADDR) (p. 492)

■ redistribute -- List protocols which are being redistributed into OSPF (p. 501)

■ restrict -- List routes which will not be redistributed via OSPF (p. 503)

■ traps -- Show OSPF traps enabled on the device (p. 515)

■ virtual-link -- Show status of all OSPF virtual links configured (p. 517)

■ area -- Specify area of the virtual links to show. (OSPF-AREA-ID) (p. 453)

■ vlink-ip -- Router ID of the link destination for which to show detailed information.

(IP-ADDR) (p. 521)

■ virtual-neighbor -- Show all virtual neighbors of the device (p. 518)

■ area -- Specify area of the virtual neighbors to show. (OSPF-AREA-ID) (p. 453)

■ vneighbor-ip -- Router ID of the virtual neighbor for which to show detailed information.

(IP-ADDR) (p. 521)

■ pim -- Show PIM protocol operational and configuration information (p. 495)

■ bsr -- Show Bootstrap Router information (p. 458)

■ elected -- Show elected Bootstrap Router information. (p. 470)

■ local -- Show local Candidate-BSR configuration information. (p. 486)

■ interface -- Show PIM interface information (p. 479)

■ VLAN-ID -- Specify the VLAN ID of the PIM interface to show. (VLAN-ID) (p. 520)

■ mroute -- Show PIM-specific information from the IP multicast routing table (p. 490)

■ IP-ADDR -- Specify the IP multicast group address of the MRT entry. (IP-ADDR) (p. 481)

■ IP-ADDR -- Specify the source IP address of the MRT entry. (IP-ADDR) (p. 481)

■ neighbor -- Show PIM neighbor information (p. 492)

■ IP-ADDR -- Specify the IP address of the PIM neighbor to show. (IP-ADDR) (p. 481)

■ pending -- Show (*,G) and (S,G) Join Pending Information. (p. 495)

■ rp-candidate -- Show Candidate-RP operational and configuration information (p. 505)

■ config -- Show C-RP configuration information. (p. 462)

■ rp-pending -- Show (*,*,RP) Join Pending Information. (p. 505)

■ rp-set -- Show RP-Set information available on the router (p. 505)

■ learned -- Show RP-Set information learned from the BSR. (p. 484)

■ static -- Show statically configured RP-Set information. (p. 510)

■ rip -- Show RIP operational and configuration information (p. 503)

■ general -- Show RIP basic configuration and operational information (p. 473)

■ interface -- Show RIP interfaces' information (p. 479)

■ if-ip -- Specify IP address of the interface for which to show detailed information.

(IP-ADDR) (p. 476)

■ vlan -- Specify VLAN of the interface for which to show detailed information. (VLAN-ID)

(p. 518)

showCommand Line Interface Reference Guide