Product manual

link-local -- Configure a link-local IPv6 address. (p. 234)■
■ ipv6-addr/mask -- Configure IPv6 address represented in CIDR notation.
(IPV6-ADDR/PREFIX-LEN) (p. 231)
■ anycast -- Address that is assigned to a set of interfaces that typically belong to
different nodes (p. 209)
■ eui-64 -- An IPv6 EUI-64 address that can be automatically configured on any interface
(p. 219)
■ enable -- Enable IPv6 on an interface and configures an automatically generated link-local
addr. (p. 219)
■ mld -- Enable/disable/configure IPv6 Multicast Listener Discovery (MLD) feature on a VLAN
(p. 237)
■ auto -- Instruct the device to monitor incoming multicast traffic on the specified ports
(this is the default behavior) ([ethernet] PORT-LIST) (p. 212)
■ blocked -- Instruct the device to drop incoming multicast packets received on the specified
ports ([ethernet] PORT-LIST) (p. 214)
■ fastleave -- Enables MLD fast-leaves on the specified ports in the selected VLAN
([ethernet] PORT-LIST) (p. 219)
■ forcedfastleave -- Enables MLD Forced Fast-Leave on the specified ports in the selected
VLAN, even if they are cascaded ([ethernet] PORT-LIST) (p. 220)
■ forward -- Instruct the device to forward incoming multicast packets received on the
specified ports ([ethernet] PORT-LIST) (p. 221)
■ querier -- This command disables or re-enables the ability for the switch to become
querier if necessary (p. 255)
■ jumbo -- Labels this VLAN as a Jumbo VLAN, allowing you to pass packets up to 9220 bytes
in size (p. 232)
■ monitor -- Define either the VLAN is to be monitored or not (p. 238)
■ all < In | Out | Both > -- Monitor all traffic. (p. 207)
■ mirror -- Mirror destination. (p. 236)
■ mirror_session_name -- Mirror destination name. (p. 237)
■ monitor_mirror_session_id < 1 to 4 > -- Mirror destination number. (p. 241)
■ ip -- Apply an IPv4 access list. (p. 225)
■ access-group -- Define the mirror port for diagnostic purposes (ASCII-STR) (p. 201)
■ monitor_mirror_ACL_dir < In > -- Define the mirror port for diagnostic purposes (p.
240)
■ mirror -- Mirror destination. (p. 236)
■ mirror_session_name -- Mirror destination name. (p. 237)
■ monitor_mirror_session_id < 1 to 4 > -- Mirror destination number. (p. 241)
■ name -- Set the VLAN's name (ASCII-STR) (p. 242)
■ protocol -- Set a predefined protocol for the current VLAN. (p. 253)
■ protocol-group -- Enter a list of protocols for the current VLAN delimited by commas.
(ASCII-STR) (p. 253)
■ protocols < IPX | IPv4 | IPv6 | ... > -- Set a predefined protocol for the current VLAN. (p. 253)
■ qos -- Set VLAN-based priority (p. 254)
■ dscp < 000000 | 000001 | 000010 | ... > -- Specify DSCP policy to use. (p. 218)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 251)
■ tagged -- Assign ports to current VLAN as tagged ([ethernet] PORT-LIST) (p. 263)
■ untagged -- Assign ports to current VLAN as untagged ([ethernet] PORT-LIST) (p. 266)
■ voice -- Labels this VLAN as a Voice VLAN, allowing you to separate, prioritize, and authenticate
voice traffic moving through your network (p. 267)
■ vrrp -- Enable/disable/configure VRRP operation on the VLAN (p. 268)
■ vrid < 1 to 255 > -- Configure a virtual router instance for the VLAN (p. 268)
■ advertise-interval < 1 to 255 > -- Set time interval (in seconds) between sending VRRP
advertisement messages (p. 206)
199© 2008 Hewlett-Packard Development Company, L.P.
interfaceCommand Line Interface Reference Guide