Product manual

port-type -- Configure qinq port-type (p. 249)■
■ customer-network -- Configure qinq port-type as customer-network (p. 216)
■ provider-network -- Configure qinq port-type as provider-network (p. 254)
■ qos -- Set port-based priority (p. 254)
■ dscp < 000000 | 000001 | 000010 | ... > -- Specify DSCP policy to use. (p. 218)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 251)
■ rate-limit -- Enable/disable and configure rate-limiting for all traffic (or for incoming ICMP
traffic) on the port(s) (p. 258)
■ all -- Set limits for all traffic. (p. 207)
■ in -- Set limits for all inbound traffic. (p. 225)
■ kbps < 0 to 10000000 > -- Specify limit of allowed inbound or outbound traffic in
kilobits-per-second on the specified port(s). Actual limits are in steps of 100Kbps to
100Mbps (granularity is 1% of the lowest related media speed). (p. 232)
■ percent < 0 to 100 > -- Specify limit as percent of inbound or outbound traffic. (p.
245)
■ out -- Set limits for all outbound traffic. (p. 244)
■ kbps < 0 to 10000000 > -- Specify limit of allowed inbound or outbound traffic in
kilobits-per-second on the specified port(s). Actual limits are in steps of 100Kbps to
100Mbps (granularity is 1% of the lowest related media speed). (p. 232)
■ percent < 0 to 100 > -- Specify limit as percent of inbound or outbound traffic. (p.
245)
■ icmp -- Set limits for ICMP traffic only. (p. 224)
■ kbps < 0 to 10000000 > -- Specify kilobits-per-second limit of allowed ICMP traffic (values
should be at least 13Kbps, or max-length ICMP packets will fail.) (p. 232)
■ percent < 0 to 100 > -- Specify limit as percent of inbound or outbound traffic. (p. 245)
■ ip -- Apply the specified access control list to inbound packets on this INTERFACE list (p.
225)
■ access-group -- Apply the specified access control list to inbound packets on this
INTERFACE list (p. 201)
■ access-group -- Apply the specified access control list to inbound packets on this
INTERFACE list (ASCII-STR) (p. 201)
■ direction < in > -- (p. 217)
■ kbps < 1 to 10000000 > -- Specify rate-limit in kilo-bits-per-second. (NUMBER)
(p. 232)
■ speed-duplex < 10-half | 100-half | 10-full | ... > -- Define mode of operation for the port(s) (p.
261)
■ type < Trunk | | | ... > -- (p. 264)
■ unknown-vlans < Learn | Block | Disable > -- Configure GVRP on the port(s) (p. 265)
■ [no] interface svlan -- Add, delete, edit SVLAN configuration or enter a SVLAN context (VLAN-ID)
(p. 262)
■ auto -- Cause each port identified in the port list to learn its VLAN membership using the GARP
VLAN Registration Protocol (GVRP) ([ethernet] PORT-LIST) (p. 212)
■ connection-rate-filter -- Re-enables access to a host or set of hosts that has been previously
blocked by the connection rate filter (p. 215)
■ unblock -- Resets a host previously blocked by the connection rate filter (p. 265)
■ all -- Resets all previously blocked by the connection rate filter (p. 207)
■ host -- Match packets from the specified IP address. (IP-ADDR) (p. 224)
■ src-ip -- Match packets from the specified subnet. (IP-ADDR/MASK-LENGTH) (p. 262)
■ dhcp-snooping -- (p. 217)
■ forbid -- Prevent ports from becoming a member of the current VLAN ([ethernet] PORT-LIST)
(p. 220)
■ ip -- Configure various IP parameters for the VLAN (p. 225)
193© 2008 Hewlett-Packard Development Company, L.P.
interfaceCommand Line Interface Reference Guide