Specifications

ManualsBrandsProCurve ManualsNetworking2610-PWR

Power over Ethernet

ProCurve 2610 Switches

Installation and Getting Started Guide

Summary of content (112 pages)

PAGE 1
ProCurve 2610 Switches Installation and Getting Started Guide Power over Ethernet
PAGE 2
PAGE 3
HP ProCurve 2610 Switches Installation and Getting Started Guide
PAGE 4
Disclaimer © Copyright 2007 - 2009 Hewlett-Packard Development Company, L.P. HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
PAGE 5
Contents 1 Introducing the Switch Front of the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Network Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 6
. Installing or Removing mini-GBICs . . . . . . . . . . . . . . . . . . . . . . . . . Installing the mini-GBICs: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing the mini-GBICs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting Cables to mini-GBICs . . . . . . . . . . . . . . . . . . . . . . . . . 7. (Optional) Connect a Redundant Power Supply to a Switch 2610-PWR Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 7
4 Troubleshooting Basic Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Diagnosing with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 LED patterns for General Switch Troubleshooting . . . . . . . . . . . . . . . 4-4 LED Patterns for PoE Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Proactive Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
B Cabling and Technology Information Cabling specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1 Technology distance specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 Mode Conditioning Patch Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Installing the Patch Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Twisted-Pair Cable/Connector Pin-Outs . . . . . . . . . . . . . . . . . . . . .
PAGE 9
D Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements . . . . . .
PAGE 10
PAGE 11
1 Introducing the Switch HP ProCurve Switch 2610-24 (J9085A) HP ProCurve Switch 2610-48 (J9088A) HP ProCurve Switch 2610-24/12PWR (J9086A) HP ProCurve Switch 2610-24-PWR (J9087A) HP ProCurve Switch 2610-48-PWR (J9089A) 1-1 Introducing the Switch The ProCurve 2610 Switches are multiport switches that can be used to build high-performance switched workgroup networks. These switches are storeand-forward devices that offer low latency for high-speed networking.
PAGE 12
Introducing the Switch Introducing the Switch Throughout this manual, these switches will be referred to as the 2610 Switches and the 2610-PWR Switches. ■ The 2610 Switches, has either 24 or 48 auto-sensing 10/100Base-TX RJ-45 ports with four Gigabit Uplink ports, two RJ-45 and two mini-GBIC (Small Form Factor Pluggable (SFP)) slots. For a list of supported mini-GBICs see page 2-17. The RJ-45 Gigabit Uplink ports are auto-sensing 10/100/1000Base-T.
PAGE 13
Introducing the Switch For further information regarding PoE power, see the PoE Planning and Implementation Guide, which is on the ProCurve Web site at www.hp.com/go/procurve/manuals, (See page 1-13).
PAGE 14
Introducing the Switch Introducing the Switch Front of the Switch Front of the Switch Power and Fault LEDs Console Port Power and Fault LEDs Console Port Power and Fault LEDs RPS, Fan and Test Status LEDs 1-4 LED Mode select button and indicator LEDs Reset and Clear buttons RPS, EPS, Fan and Test Status LEDs 10/100Base-TX RJ-45 ports1 Switch port LEDs LED Mode select button and indicator LEDs Reset and Clear buttons Uplink ports (1000Base-T2 and mini-GBIC) ProCurve Switch 2610-48-PWR 10/10
PAGE 15
Introducing the Switch Front of the Switch Network Ports 24, or 48 auto-sensing 10/100Base-TX ports. All these ports have the “Auto-MDIX” feature, which means that you can use either straight-through or crossover twisted-pair cables to connect any network devices to the switch. ■ Two RJ-45 10/100/1000Base-T ports for high speed uplink. ■ Two mini-GBIC (SPF) slots for fiber uplinks.
PAGE 16
Introducing the Switch Introducing the Switch Front of the Switch Switch LEDs State Meaning PoE (green/ orange)3 On Normal operation. The switch is ready to supply PoE power Flashing/ orange2 One or more ports has experienced a fault condition for PoE delivery. The Fault LED will be flashing simultaneously. If it is a self test failure, the Test LED will be flashing simultaneously.
PAGE 17
Introducing the Switch Front of the Switch State Meaning Test (green/ orange) Off The normal operational state; the switch is not undergoing self test. On The switch self test and initialization are in progress after the switch has been power cycled or reset. The switch is not operational until this LED goes off. The Test LED also comes on briefly when you “hot swap” a miniGBIC into the switch; the mini-GBIC is tested when it is hot swapped.
PAGE 18
Introducing the Switch Front of the Switch Introducing the Switch Port LEDs The port LEDs provide information about the individual switch ports. Table 1-3. Switch LEDs Port LEDs State Meaning Switch 2610 non-PWR Series Port LEDs Mini-GBIC LEDs: Link Link and Mode (green) Displays port link information, network activity information, whether the port is configured for full-duplex operation, or the speed of the connection depending on the LED Mode selected.
PAGE 19
Introducing the Switch Front of the Switch LED Mode Select Button and Indicator LEDs The non-PWR switches, have two LEDs per port. The Link status is always shown by the Link LED. The operation of the Mode LED is controlled by the LED Mode select button, and the current setting is indicated by the LED Mode indicator LEDs near the button. Press the button to step from one view mode to the next. The default view is Activity (Act). Link LED Mode LED LED Mode select button and indicator LEDs Figure 1-1.
PAGE 20
Introducing the Switch Front of the Switch Introducing the Switch Table 1-4. Switch LEDs State Multiple-Display Port LEDs Meaning All 2610 Switches Port LED View indicator LEDs 3 green LEDs) Act FDx Spd Indicates the Port LEDs are displaying network activity information. Indicates the Port LEDs are lit for ports that are in full-duplex mode. Indicates the Port LEDs are displaying the connection speed at which each port is operating: • if the Port LED is off, the port is operating at 10 Mbps.
PAGE 21
Introducing the Switch Back of the Switch Console Port Back of the Switch RPS Input AC power connector Figure 1-3. ProCurve Switch 2610-24 and 2610-48 non-PWR EPS Input AC power connector RPS Input Figure 1-4. ProCurve Switch 2610-24-PWR and 2610-48-PWR EPS Input RPS Input AC power connector Figure 1-5. ProCurve Switch 2610-24/12PWR 1-11 Introducing the Switch This port is used to connect a console to a 2610 Switches by using the RJ-45 to DB9 cable, supplied with the switch.
PAGE 22
Introducing the Switch Switch Features Introducing the Switch RPS and EPS Input Port The 2610 Switches support connectivity to a redundant power supply (RPS/ EPS). The ProCurve 600 Redundant and External Power Supply (J8168A) and the ProCurve 610 External Power Supply (J8169A) are accessory products for these switches. The RPS functionality of the 600 procides redundant system power in case the switch’s internal power supply fails.
PAGE 23
Introducing the Switch Switch Features Automatically negotiated full-duplex operation for the 10/100 and 10/100/1000 RJ-45 ports when connected to other auto-negotiating devices—the mini-GBIC ports always operate at full duplex, unless a 100-FX SFP transceiver is installed. The 100-FX SFP transceiver can operate at half duplex.
PAGE 24
PAGE 25
2 Installing the Switch The ProCurve 2610 Switches come with an accessory kit that includes the brackets for mounting the switch in a standard 19-inch telco rack, in an equipment cabinet, or on a wall. The brackets are designed to allow mounting the switch in a variety of locations and orientations. Rubber feet are provided that can be attached so the switch can be securely located on a horizontal surface. Installing the Switch This chapter shows how to install the Switch 2610.
PAGE 26
Installing the Switch Included Parts Installing the Switch ■ AC power cord, one of the following: Australia/New Zealand China Continental Europe Denmark Japan Switzerland United Kingdom/Hong Kong/Singapore United States/Canada/Mexico South Africa Thailand Taiwan India Non-PWR Switches PWR Switches 1 8120-6803 8120-8377 8120-6802 8120-6806 8120-6804 8120-6807 8120-8709 8120-6805 8120-8929 8121-0673 8121-0964 8121-0780 8120-6810 8120-8471 8120-6811 8120-6814 8120-6804 8120-6815 8120-6809 8120-2371 812
PAGE 27
Installing the Switch Included Parts Installation Precautions WARNING ■ The rack or cabinet should be adequately secured to prevent it from becoming unstable and/or falling over. Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest devices at the bottom and progressively lighter devices installed above. For safe operation do not install the switch with the side of the switch (with the fan vents) facing either downward or upward.
PAGE 28
Installing the Switch Installation Procedures Installation Procedures Installing the Switch These steps summarize your switch installation. The rest of this chapter provides details on these steps. 1. Prepare the installation site (page 2-6). Make sure the physical environment into which you will be installing the switch is properly prepared, including having the correct network cabling ready to connect to the switch and having an appropriate location for the switch.
PAGE 29
Installing the Switch Installation Procedures 8. (Optional) Connect a console to the switch (page 2-26). You may wish to modify the switch’s configuration, for example, to configure an IP address so it can be managed using a web browser, from an SNMP network management station, or through a Telnet session. Configuration changes can be made by using the included console cable to connect a PC to the switch’s console port. At this point, your switch is fully installed.
PAGE 30
Installing the Switch Installation Procedures 1. Prepare the Installation Site Cabling Infrastructure - Ensure the cabling infrastructure meets the necessary network specifications.
PAGE 31
Installing the Switch Installation Procedures Note The 2610 Switches do not have a power switch. They are powered on when the power cord is connected to the switch and to a power source. For safety, the power outlet should be located near the switch installation. The switch automatically adjusts to any voltage between 100-127 or 200-240 volts and either 50 or 60 Hz. There are no voltage range settings required. 2. Check the LEDs on the switch as described below.
PAGE 32
Installing the Switch Installation Procedures When the switch is powered on, it performs its diagnostic self test. Self test takes approximately 50 seconds to complete. Self Test LED Switch port LEDs Installing the Switch Power and Fault LEDs Figure 2-3. Checking the LEDs on the 2610-PWR switches LED Behavior During the self test: • Initially, all the switch and port LEDs are on. Most of the LEDs go off and then may come on again during phases of the self test.
PAGE 33
Installing the Switch Installation Procedures 3. Mount the Switch After the switch passes self test, it is ready to be mounted in a stable location. The 2610 Switches can be mounted in these ways: Mounting Location Non-PWR Switches PWR Switches In a rack or cabinet Yes Yes On a horizontal surface Yes Yes On a wall Yes No The 2610 Switches are designed to be mounted in any EIA-standard 19-inch telco rack or communication equipment cabinet.
PAGE 34
Installing the Switch Installation Procedures Rack Mounting the 2610-PWR switches Installing the Switch 1. Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the switch with the included 8-mm M4 screws. Figure 2-4. Attaching large mounting brackets WARNING For safe reliable installation, only use the screws provided in the accessory kit to attach the mounting brackets to the switch.
PAGE 35
Installing the Switch Installation Procedures 2. Hold the switch with attached brackets up to the rack and move it vertically until rack holes line up with the bracket holes, then insert and tighten the four number 12-24 screws holding the brackets to the rack. Installing the Switch Install 12-24 screws Figure 2-5.
PAGE 36
Installing the Switch Installation Procedures Rack Mounting the Non-PWR Switches Installing the Switch 1. Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the switch with the included 8-mm M4 screws. 8 mm M4 screws Figure 2-6. Attaching small mounting brackets Note The mounting brackets have multiple mounting holes and can be rotated allowing for a wide variety of mounting options.
PAGE 37
Installing the Switch Installation Procedures 2. Hold the switch with attached brackets up to the rack and move it vertically until rack holes line up with the bracket holes, then insert and tighten the four number 12-24 screws holding the brackets to the rack. Installing the Switch Install 12-24 screws Figure 2-7.
PAGE 38
Installing the Switch Installation Procedures Flat Wall Mounting There are two switches in this series that can be wall mounted, the J9085A 24port Non-PoE and the J9088A 48-port Non-PoE. You can mount these switches on a wall as shown in the illustration Figure 2-8. Wall mounting is not supported for the 2610-PWR switches because of the size and weight of the devices. See page 2-14 for instructions. For safe operation do not install the switch with either side vent holes (vertical) facing downward.
PAGE 39
Installing the Switch Installation Procedures RJ-45 Ports Wall Installing the Switch M4 screws 5/8-inch wood screws Figure 2-8. Horizontal wall mounting Caution The J9088A 48-port, non-PWR switch can be wall mounted with either the RJ-45 ports side up or down in the horizontal orientation. A vertical wall mount orientation is not supported. The J9085A 24-port, non-PWR switch can be wall mounted with the RJ-45 port side facing down only in the horizontal orientation.
PAGE 40
Installing the Switch Installation Procedures Installing the Switch 4. Connect the Switch to a Power Source 1. Plug the included power cord into the switch’s power connector and into a nearby AC power source. 2. Re-check the LEDs during self test. See “LED Behavior” on page 2-8. Figure 2-9. Connecting the power cord 5.
PAGE 41
Installing the Switch Installation Procedures 6. Installing or Removing mini-GBICs You can install or remove a mini-GBIC from a mini-GBIC slot without having to power off the switch. Use only ProCurve mini-GBICs. Notes The mini-GBIC slots are not shared with the two 10/100/1000Base-T RJ45 ports. When a mini-GBIC is installed in a slot, it operates independently of the RJ-45 ports. ■ The mini-GBIC ports operate only at full duplex.
PAGE 42
Installing the Switch Installation Procedures Removing the mini-GBICs Note You should disconnect the network cable from the mini-GBIC before removing it from the switch. Depending on when you purchased your ProCurve mini-GBIC, it may have either of three different release mechanisms: a plastic tab on the bottom of the mini-GBIC, a plastic collar around the mini-GBIC, or a wire bail.
PAGE 43
Installing the Switch Installation Procedures The 600 RPS/EPS provides two types of power to the switches: Redundant power to one of up to six switches, to back up the internal switch power supply in case of AC power loss, or a fault condition. Should the internal switch power supply fail, power will be supplied from the 600 RPS/EPS, if it is available, that is, if the 600 RPS/EPS is not already providing power to a higher priority switch.
PAGE 44
Installing the Switch Installation Procedures The RPS/EPS supports hot plugging of the RPS/EPS cable without causing a reboot of the switch or causing the power supply in either the RPS/EPS or switch to shut down temporarily or permanently. For more information refer to the documentation that came with the RPS/EPS.
PAGE 45
Installing the Switch Installation Procedures Each pair can provide a maximum of 408 watts of PoE power to a switch if only one port is used. If the second port of a pair is used, then both ports supply 204 watts each. Again, it is important to understand the PoE power requirements of the switches. For further information regarding the 610 EPS PoE capabilities, see the PoE Planning and Implementation Guide, which is on the ProCurve Web site at www.hp.com/go/procurve/manuals, (See page 1-13).
PAGE 46
Installing the Switch Installation Procedures Installing the Switch The following states provide status of the RPS and EPS ports.
PAGE 47
Installing the Switch Installation Procedures The following illustration shows an example of connectivity between an RPS/ EPS device and six switch devices as a redundant AC power supply. RPS port 1 highest priority RPS port 6 lowest priority 600 RPS/EPS Installing the Switch 2610-PWR switches Figure 2-14. Connecting a 600 RPS/EPS to multiple 2610s RPS The 600 RPS/EPS can provide backup power for up to six switches. The 600 RPS/EPS can supply power to only one connected and failed switch at a time.
PAGE 48
Installing the Switch Installation Procedures The following illustration demonstrates an example of connectivity between an RPS/EPS device and a Switch device as a PoE power supply. Switch EPS output Installing the Switch EPS input port Figure 2-15.
PAGE 49
Installing the Switch Installation Procedures hp procurve 610 eps Pair A (408 W total for PoE applications) EPS Ports EPS A1 J8169A A1 Device Connected Power Status EPS Ports Pair B (408 W total for PoE applications) A2 B1 EPS A2 EPS B1 Device Connected Power Status B2 EPS B2 Backup Power Ports Status Power Internal Power Status EPS Ports: 50V Out Ready 8.3A max each. Fan/Temp Status flash = Temperature too high Fan/Temp Status + Fault flash = Fan failure Figure 2-17.
PAGE 50
Installing the Switch Installation Procedures 8.
PAGE 51
Installing the Switch Installation Procedures Direct Console Access To connect a console to the switch, follow these steps: 1. 3. Turn on the terminal or PC’s power and, if using a PC, start the PC terminal program. Console port Console cable supplied with the switch Installing the Switch 2. Connect the PC or terminal to the switch’s Console Port using the console cable included with the switch.
PAGE 52
Installing the Switch Sample Network Topologies for Non-PWR Switches Sample Network Topologies for Non-PWR Switches This section shows a few sample network topologies in which the Switch 2610 is implemented. For more topology information, see the ProCurve networking products Web site, www.hp.com/go/procurve/manuals. Installing the Switch As a Desktop Switch Server Twisted-pair straight-through or crossover cables Switch 2610-48 Gigabit fiber-optic cable to backbone PCs and peripherals Figure 2-20.
PAGE 53
Installing the Switch Sample Network Topologies for Non-PWR Switches As a Segment Switch Category 5e twisted-pair straight-through or crossover cable for 1000 Mbps connection to server Server with Gigabit Ethernet NIC Category 5e twisted-pair straightthrough or crossover cable for 1000 Mbps connection to backbone Switch 2610-48 Installing the Switch Gigabit fiber-optic cable Switch 2610-48 Switch 2610-48 Twisted-pair straight-through cables to end nodes PCs, printers, and local servers Figure 2-21.
PAGE 54
Installing the Switch Sample Network Topologies for Non-PWR Switches Because the 2610 Switches have the Auto-MDIX feature, the connections between the switches, and between the switch and end nodes or servers can be through category 5 straight-through or crossover twisted-pair cable. Category 3 or 4 cable can also be used if the connection is 10 Mbps only. In all cases, the device ports must be configured to auto negotiate the link characteristics for this feature to work.
PAGE 55
Installing the Switch Sample Network Topologies for Non-PWR Switches The simpler desktop and segment networks shown in the previous two examples can easily be combined and expanded. For example, you could use a ProCurve Switch 5406zl to interconnect each of your smaller switched workgroups to form a larger switched network. All the devices in this network can communicate with each other.
PAGE 56
Installing the Switch Sample Network Topologies for PWR Switches Sample Network Topologies for PWR Switches This section shows a few sample network topologies for implementing the Switch 2610-PWR Series. For more topology information, see the ProCurve networking products Web site, www.hp.com/go/procurve/manuals.
PAGE 57
Installing the Switch Sample Network Topologies for PWR Switches As a Segment Switch Implementing PoE Category 5e twisted-pair straight-through or crossover cable for 1000 Mbps connection to server Server with Gigabit Ethernet NIC Switch 2610-48 Non-PWR 600 RPS/EPS Gigabit fiber-optic cable uplink Switch 2610-48PWR Switch 2610-48-PWR Wireless Access Points PCs, printers, and local servers Figure 2-24.
PAGE 58
Installing the Switch Sample Network Topologies for PWR Switches Connecting to a Backbone Switch Implementing PoE To Gigabit-Ethernet backbone Installing the Switch Switch 5406zl Switch 2610-48 non-PWR Gigabit fiber-optic cable Switch 2610-48 non-PWR 600 RPS/EPS Switch 2610-48-PWR Switch 261048-PWR Wireless Access Point Figure 2-25.
PAGE 59
Installing the Switch Sample Network Topologies for PWR Switches Stacking the Switch Switch 2610 and 2610-PWR Series devices can be connected together, through standard network connections, and managed through a single IP address. Up to 16 switches can be connected together in such a “virtual stack”. You identify a Switch 2610 or 2610-PWR Series device as the “Commander” and give that switch an IP address.
PAGE 60
PAGE 61
3 Configuring the Switch This chapter is a guide for using the console Switch Setup screen to quickly assign an IP (Internet Protocol) address and subnet mask to the switch, set a Manager password, and, optionally, configure other basic features. For more information on using the switch console and the web browser interface, please see the Management and Configuration Guide, which is on the ProCurve Web site at www.hp.com/go/procurve/manuals, (See page 1-13).
PAGE 62
Configuring the Switch Recommended Minimal Configuration Using the Console Setup Screen The quickest and easiest way to minimally configure the switch for management and password protection in your network is to use a direct console connection to the switch, start a console session, and access the Switch Setup screen. 1. Using the method described in the preceding section, connect a terminal device to the switch and display the switch console command line interface (CLI) prompt (the default display).
PAGE 63
Configuring the Switch Recommended Minimal Configuration Here is some information on the fields in the Setup screen. For more information on these fields, see the Management and Configuration Guide, which is on the ProCurve Web site at www.hp.
PAGE 64
Configuring the Switch Recommended Minimal Configuration Some basic information on managing your switch is included in the next section. For more information on the console, web browser, and SNMP management interfaces and all the features that can be configured on the Series 2610 Switches, see the Management and Configuration Guide, which is on the ProCurve Web site at www.hp.com/go/procurve/manuals, (See page 113).
PAGE 65
Configuring the Switch Using the IP Address for Remote Switch Management Using the IP Address for Remote Switch Management With your switch, you can use the switch’s IP address to manage the switch from any PC that is on the same subnet as the switch. You can use either a Telnet session or a standard web browser to manage the switch. Starting a Telnet Session To access the switch through a Telnet session, follow these steps: 1.
PAGE 66
Configuring the Switch Using the IP Address for Remote Switch Management ProCurve Switch 2610-48 - xl Status: Information J9088A ProCurve Switch 2610-48 xl PoE Status Configuring the Switch Figure 3-2. Example web browser session For more information on using the web browser interface, please see the Management and Configuration Guide, which is on the ProCurve Web site at www.hp.com/go/procurve/manuals, (See page 1-13). An extensive help system is also available for the web browser interface.
PAGE 67
4 Troubleshooting This chapter describes how to troubleshoot your ProCurve 2610 Switches. This document describes troubleshooting mostly from a hardware perspective. You can perform more in-depth troubleshooting on these devices using the software tools available with the switches, including the fullfeatured console interface, the built-in web browser interface, and ProCurve Manager, the SNMP-based network management tool.
PAGE 68
Troubleshooting Basic Troubleshooting Tips Caution Because the 2610 Switches behave in this way (in compliance with the IEEE 802.3 standard), if a device connected to the switch has a fixed configuration at full duplex, the device will not connect correctly to the switch. The result will be high error rates and very inefficient communications between the switch and the device.
PAGE 69
Troubleshooting Basic Troubleshooting Tips ■ Check the port configuration. A port on your switch may not be operating as you expect because it has been put into a “blocking” state by Spanning Tree, GVRP (automatic VLANs), or LACP (automatic trunking). (Note that the normal operation of the Spanning Tree, GVRP, and LACP features may put the port in a blocking state.) Or, the port just may have been configured as disabled through software.
PAGE 70
Troubleshooting Diagnosing with the LEDs Diagnosing with the LEDs Table 4-1 shows LED patterns on the switch that indicate problem conditions for general switch operation troubleshooting. Table 4-2 shows LED patterns that indicate problem conditions for PoE troubleshooting. LED patterns for General Switch Troubleshooting 1. Check in the table for the LED pattern you see on your switch. 2. Refer to the corresponding diagnostic tip on the next few pages. Table 4-1.
PAGE 71
Troubleshooting Diagnosing with the LEDs Diagnostic Tips: Problem Solution ➊ The switch is not plugged into an active AC power source, or the switch’s power supply may have failed. 1. Verify the power cord is plugged into an active power source and to the switch. Make sure these connections are snug. 2. Try power cycling the switch by unplugging and plugging the power cord back in. 3. If the Power LED is still not on, verify the AC power source works by plugging another device into the outlet.
PAGE 72
Troubleshooting Diagnosing with the LEDs Tip Problem Solution ➏ The network connection is not working properly. Try the following procedures: • For the indicated port, verify that both ends of the cabling, at the switch and the connected device, are connected properly. • Verify the connected device and switch are both powered on and operating correctly.
PAGE 73
Troubleshooting Diagnosing with the LEDs Tip Problem Solution ➐ The port may be improperly configured, or the port may be in a “blocking” state by the normal operation of the Spanning Tree, LACP, or IGMP features. Use the switch console to see if the port is part of a dynamic trunk (through the LACP feature) or to see if Spanning Tree is enabled on the switch, and to see if the port may have been put into a “blocking” state by those features.
PAGE 74
Troubleshooting Diagnosing with the LEDs LED Patterns for PoE Troubleshooting If the PoE Status LED is flashing, that indicates a problem with the delivery of PoE power out one or more switch ports. Press the LED Mode button to put the switch into PoE mode and the port LEDs will show which ports are experiencing the problem. The following tables identify the specific problems that are shown by the LEDs. 1. Check in the table for the LED pattern you see on your switch. 2.
PAGE 75
Troubleshooting Proactive Networking Proactive Networking The ProCurve 2610 Switches have built-in management capabilities that proactively help you manage your network including: ■ finding and helping you fix the most common network error conditions (for example, faulty network cabling, and non-standard network topologies) ■ informing you of the problem with clear, easy-to-understand messages ■ recommending network configuration changes to enhance the performance of your network The following interf
PAGE 76
Troubleshooting Hardware Diagnostic Tests Hardware Diagnostic Tests Testing the Switch by Resetting It If you believe the switch is not operating correctly, you can reset the switch to test its circuitry and operating code.
PAGE 77
Troubleshooting Hardware Diagnostic Tests Testing Twisted-Pair Cabling Network cables that fail to provide a link or provide an unreliable link between the switch and the connected network device may not be compatible with the IEEE 802.3 Type 10Base-T, 100Base-TX, or 1000Base-T standards. The twistedpair cables attached to the switch must be compatible with the appropriate standards. To verify your cable is compatible with these standards, use a qualified cable test device.
PAGE 78
Troubleshooting Restoring the Factory Default Configuration Restoring the Factory Default Configuration As part of your troubleshooting process on the Switch, it may become necessary to return the switch configuration to the factory default settings. This clears any passwords, clears the console event log, resets the network counters to zero, performs a complete self test, and reboots the switch into its factory default configuration including deleting the IP address, if one is configured.
PAGE 79
Troubleshooting Downloading New Switch Software Downloading New Switch Software When product enhancements occur for the 2610 Switches, new software can be downloaded to the switch through several methods, for product enhancements and new features. For more information, see the Management and Configuration Guide, which is on the ProCurve Web site at www.hp.com/ go/procurve/manuals, (See page 1-13). The new switch software would be available on the ProCurve Web site, www.hp.com/go/procurve/manuals.
PAGE 80
PAGE 81
A Switch Specifications Switch Specifications Physical Width Depth Height Weight 2610-24 (J9085A) 44.3 cm (17.4 in) 23.5 cm (9.3 in) 4.4 cm (1.73 in) 4.63 kg (10.20 lbs) 2610-48 (J9088A) 44.3 cm (17.4 in) 23.5 cm (9.3 in) 4.4 cm (1.73 in) 4.88 kg (10.75 lbs) 2610-24/12PWR (J9086A) 44.3 cm (17.4 in) 23.5 cm (9.3 in) 4.4 cm (1.73 in) 3.4 kg (7.5 lbs) 2610-24-PWR (J9087A) 44.3 cm (17.4 in) 31.8 cm (12.5 in) 4.4 cm (1.73 in) 6.83 kg (15.05 lbs) 2610-48-PWR (J9089A) 44.3 cm (17.
PAGE 82
Switch Specifications Switch Specifications RPS/EPS Electrical Input 2610 Non-PWR Series Input voltage Maximum current RPS Input +12 VDC 7.5A EPS Input N/A N/A Input voltage Maximum current RPS Input +12 VDC 7.5A EPS Input -50 VDC 16A 2610-PWR Series Environmental 2610 Switches Operating Non-Operating Temperature 0°C to 50°C (32°F to 122°F) -40°C to 70°C (-40°F to 158°F) Relative humidity (non-condensing) 15% to 95% at 40°C (104°F) 15% to 90% at 65°C (149°F) Maximum altitude 3.
PAGE 83
Switch Specifications Acoustics Switch Specifications Non-PWR Switches Switch 2610-24 (J9085A) No fans. Switch 2610-48 (J9088A) Geraeuschemission LwA=36.2 dB am fiktiven Arbeitsplatz nach DIN 45635 T.19 Noise Emission LwA=36.2 dB at virtual work space according to DIN 45635 T.19 PWR switches Switch 2610-24/12PWR (J9086A) Geraeuschemission LwA=38.4 dB am fiktiven Arbeitsplatz nach DIN 45635 T.19 Noise Emission LwA=38.4 dB at virtual work space according to DIN 45635 T.
PAGE 84
Switch Specifications Switch Specifications Safety Complies with: ■ EN60950-1/IEC60950-1 ■ CSA 22.2 No. 60950-1 ■ UL 60950-1 Table A-1. Technology standards and safety compliance Laser safety information Technology 10 100 1000-T A-4 Compatible with these IEEE standards EN/IEC standard compliance SFP ("mini-GBIC") Lasers IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000BASE-T 100-FX IEEE 802.3u 100BASE-FX EN/IEC 60825 Class 1 Laser Product Laser Klasse 1 100-BX IEEE 802.
PAGE 85
B Cabling and Technology Information This appendix includes network cable information for cables that should be used with the Switch 2610, including minimum pin-out information and specifications for twisted-pair cables. Note Cabling specifications Table B-1. 10 Mbps Operation Category 3, 4, or 5 100-ohm unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable, complying with IEEE 802.3 10Base-T specifications. 100 Mbps Operation Category 5 100-ohm UTP or STP cable, complying with IEEE 802.
PAGE 86
Cabling and Technology Information Note on 1000Base-T Cable Requirements. The Category 5 networking cables that work for 100Base-TX connections should also work for 1000Base-T, as long as all four-pairs are connected. But, for the most robust connections you should use cabling that complies with the Category 5e specifications, as described in Addendum 5 to the TIA-568-A standard (ANSI/ TIA/EIA-568-A-5).
PAGE 87
Cabling and Technology Information Mode Conditioning Patch Cord The following information applies to installations in which multimode fiberoptic cables are connected to a Gigabit-LX port. Multimode cable has a design characteristic called “Differential Mode Delay”, which requires the transmission signals be “conditioned” to compensate for the cable design and thus prevent resulting transmission errors.
PAGE 88
Cabling and Technology Information Twisted-Pair Cable/Connector Pin-Outs To network multimode cabling Cabling and Technology Information The multimode cable in the patch cord must match the characteristics of your network cable Tx Rx Gigabit-LX port LC Connector Mode Conditioning Patch Cord Single-mode section plugs into Tx port on Gigabit-LX Transceiver or Gigabit-LX mini-GBIC Figure B-1.
PAGE 89
Cabling and Technology Information Twisted-Pair Cable/Connector Pin-Outs Other Wiring Rules: All twisted-pair wires used for 10 Mbps, and 100 Mbps operation must be twisted through the entire length of the cable. The wiring sequence must conform to EIA/TIA 568-B (not USOC). See “Twisted-Pair Cable Pin Assignments” later in this appendix for a listing of the signals used on each pin. ■ For 1000Base-T connections, all four pairs of wires in the cable must be available for data transmission.
PAGE 90
Cabling and Technology Information Twisted-Pair Cable/Connector Pin-Outs Straight-through Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connections Because of the Auto-MDIX operation of the 10/100 ports on the switch, for all network connections, to PCs, servers or other end nodes, or to hubs or other switches, you can use straight-through cables.
PAGE 91
Cabling and Technology Information Twisted-Pair Cable/Connector Pin-Outs Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection The Auto-MDIX operation of the 10/100 ports on the switch also allows you to use crossover cables for all network connections, to PCs, servers or other end nodes, or to hubs or other switches.
PAGE 92
Cabling and Technology Information Twisted-Pair Cable/Connector Pin-Outs Straight-Through Twisted-Pair Cable for 1000 Mbps Network Connections 1000Base-T connections require that all four pairs of wires be connected. Cabling and Technology Information Cable Diagram Note Pins 1 and 2 on connector “A” must be wired as a twisted pair to pins 1 and 2 on connector “B”. Pins 3 and 6 on connector “A” must be wired as a twisted pair to pins 3 and 6 on connector “B”.
PAGE 93
C Safety and EMC Regulatory Statements Safety Information ! Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death. Caution A Caution in the manual denotes a hazard that can damage equipment. Do not proceed beyond a WARNING or Caution notice until you have understood the hazardous conditions and have taken appropriate steps.
PAGE 94
Safety and EMC Regulatory Statements Informations concernant la sécurité Informations concernant la sécurité ! Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la documentation du produit afin d'obtenir des informations plus détaillées. WARNING Dans la documentation, un WARNING indique un danger susceptible d'entraîner des dommages corporels ou la mort.
PAGE 95
Safety and EMC Regulatory Statements Hinweise zur Sicherheit Hinweise zur Sicherheit ! Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten. WARNING Eine WARNING in der Dokumentation symbolisiert eine Gefahr, die Verletzungen oder sogar Todesfälle verursachen kann. Caution Caution in der Dokumentation symbolisiert eine Gefahr, die dis Gerät beschädigen kann.
PAGE 96
Safety and EMC Regulatory Statements Considerazioni sulla sicurezza Considerazioni sulla sicurezza ! Simbolo di riferimento alla documentazione. Se il prodotto è contrassegnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso. WARNING La dicitura WARNINGdenota un pericolo che può causare lesioni o morte. Caution La dicituraCaution denota un pericolo che può danneggiare le attrezzature.
PAGE 97
Safety and EMC Regulatory Statements Consideraciones sobre seguridad Consideraciones sobre seguridad ! Símbolo de referencia a la documentación. Si el producto va marcado con este símbolo, consultar la documentación del producto a fin de obtener mayor información sobre el producto. WARNING Una WARNING en la documentación señala un riesgo que podría resultar en lesiones o la muerte. Caution Una Caution en la documentación señala un riesgo que podría resultar en averías al equipo.
PAGE 98
Safety and EMC Regulatory Statements Safety Information (Japan) Safety and EMC Regulatory Statements Safety Information (Japan) Japan Power Cord Warning C-6
PAGE 99
Safety and EMC Regulatory Statements Safety Information (China) Safety Information (China) Safety and EMC Regulatory Statements C-7
PAGE 100
Safety and EMC Regulatory Statements EMC Regulatory Statements EMC Regulatory Statements U.S.A. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment.
PAGE 101
Safety and EMC Regulatory Statements EMC Regulatory Statements Korea Taiwan Safety and EMC Regulatory Statements ᳝↦ǃ᳝ᆇ⠽䋼/‫ܗ‬㋴ঞ݊৿䞣㸼 ձ✻Ё೑ ǉ⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩Ǌ ᳝↦ǃ᳝ᆇ⠽䋼੠‫ܗ‬㋴䚼ӊৡ⿄䬝 (Cd) ݁Ӌ䫀 (Cr(VI)) ໮⒈㘨㣃 (PBB) ໮⒈ҷѠ㣃䝮 3%'( 䪙 (Pb) ∲ (Hg) ᴎㆅ/䱨ᵓ/݊ᅗ䞥 ሲ੠ล᭭䚼ӊ 0 0 0 0 0 0 ॄࠋ⬉䏃㒘ӊ (PCA) X 0 0 0 0 0 ໽㒓 X 0 0 0 0 0 ⬉㓚/⬉㒓 X 0 0 0 0 0 ⬉∴ 0 0 0 0 0 0 亢᠛/亢᠛Ⲭ 0 0 0 0 0 0 ⬉⑤/⬉⑤䗖䜡఼ X 0 0 0 0 0 ᅝ㺙ᬃᶊ/݊ᅗ䰘 ӊ 0 0 0 0 0
PAGE 102
Safety and EMC Regulatory Statements EMC Regulatory Statements European Community DECLARATION OF CONFORMITY according to ISO/IEC 17050-1 and EN17050-1 ______________________________________________________________________ Supplier's Name: Hewlett-Packard Company Supplier's Address: 8000 Foothills Blvd. Roseville, CA 95747-5502 U.S.A.
PAGE 103
D Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
PAGE 104
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana. Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen.
PAGE 105
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnandole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche.
PAGE 106
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Descarte de Lixo Elétrico na Comunidade Européia Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico), encaminhando-o para um ponto de coleta para reciclagem.
PAGE 107
Index Numerics A AC power connector location on back of switch … 1-11 acoustic specifications … A-3 auto MDI/MDI-X operation … B-6, B-8 HP Auto-MDIX feature … B-4 B back of switch description … 1-11 power connector … 1-12 RPS input port … 1-12 backbone switch topology with … 2-30, 2-34–2-35 basic switch configuration IP address … 3-2 manager password … 3-2 subnet mask … 3-2 Switch Setup screen … 3-2 Index 10/100Base-TX ports location on switch … 1-4 1000Base-BX … B-2 fiber-optic cable specifications … B
PAGE 108
Index CLI prompt, console displaying … 2-27 configuration … 2-17 checking when troubleshooting … 4-3 DHCP/Bootp … 3-1 IP address … 3-2 IP address, manually … 3-2 manager password … 3-2 restoring factory defaults … 1-10, 4-12 subnet mask … 3-2 Switch Setup screen … 3-2 connecting the switch to a power source … 2-16 connecting the switch to an EPS … 2-24–2-25 connecting the switch to an RPS/EPS … 2-22–2-24 connector specifications … A-3 console checking messages during troubleshooting … 4-10 displaying the C
PAGE 109
M horizontal surface mounting switch on … 2-15 HP Auto-MDIX feature description … B-4 MDI-X to MDI network cable … B-6, B-8 MDI-X to MDI-X network cable … B-7 mini-GBICs full-duplex operation half-duplex operation … 2-17 slot, location on switch … 1-4 mounting the switch in a rack or cabinet … 2-9 precautions … 2-3 on a horizontal surface … 2-15 on a wall … 2-14 precautions … 2-14 Multiple-Display Port LEDs … 1-9 I in-band … 3-1 in-band console access types of … 2-26 included parts … 2-1 installation con
PAGE 110
Index pin-outs twisted-pair cables … B-4 PoE LED patterns … 4-8 PoE troubleshooting … 4-8 port configuration checking when troubleshooting … 4-3 port LEDs description … 1-8 normal operation … 2-8 ports 10/100Base-TX, location on switch … 1-4 connecting to … 2-16 console … 2-26 HP Auto-MDIX feature … B-4 network connections … 2-16 power connector … 1-12 Power LED … 1-5 behavior during self test … 2-8 behaviors … 1-5 location on switch … 1-4 power source connecting the switch to … 2-16 Power-over-Ethernet Po
PAGE 111
T technology distance specifications … B-2 Telnet access to the console … 3-5 terminal configuration … 2-26 testing checking the console messages … 4-10 checking the LEDs … 4-10 diagnostic tests … 4-10 end-to-end communications … 4-11 link test … 4-11 Ping test … 4-11 switch operation … 4-10 switch-to-device communications … 4-11 twisted-pair cabling … 4-11 tips for troubleshooting … 4-1 topologies effects of improper topology … 4-2 samples of … 2-28, 2-32 troubleshooting … 4-1 basic tips … 4-1 checking po
PAGE 112
ProCurve 5400zl Switches Installation and Getting Startd Guide Technology for better business outcomes To learn more, visit www.hp.com/go/procurve/ © Copyright 2007 - 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.