Specifications

ManualsBrandsProcom ManualsHeaterML170EPC

OWNER

’

S OPERATION AND INSTALLATION MANUAL

WARNING: Improper installation,

adjustment, alteration, service or main-

tenance can cause injury or property

damage. Refer to this manual for correct

installation and operational procedures.

For assistance or additional information

consult a qualified installer, service agency,

or gas supplier.

This appliance may be installed in an

aftermarket* permanently located, manufac-

tured (mobile) home, where not prohib-

ited by local codes.

This appliance is only for use with the

type of gas indicated on the rating plate.

This appliance is not convertible for use

with other gases.

*Aftermarket: Completion of sale, not for purpose of

resale, from the manufacturer.

Do not store, or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS

l Do not try to light any appliance.

l Do not touch any electrical switch; do not

use any phone in your building.

l Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

l If you cannot reach your gas supplier, call

the fire department.

Installation and service must be performed by a

qualified installer, service agency or gas

supplier.

MN200EPC MN200EHPC

MN300EPC MN300EHPC

INFRARED VENT-FREE

NATURAL GAS

SPACE HEATER

WARNING: If the information in

this manual is not followed exactly, a

fire or explosion may result causing

property damage, personal injury, or loss

of life.

WARNING: This is an unvented gas-

fired heater. It uses air (oxygen) from the

room in which it is installed. Provisions

for adequate combustion and ventilation

air must be provided. Refer to Air For

Combustion and Ventilation section on

page 5 of this manual.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM

HEATERS

Water vapor is a by-product of gas combustion.An

unvented room heater produces approximately one (1)

ounce (30ml) of water for every 1,000 BTU’s

(.3KW’s) of gas input per hour. Refer to page 4.

Installer: Please leave these instructions with the

consumer.

Consumer: Please retain these instructions for

future use.

Continental Appliance Inc./US Office

5 Musick 4600 Highlands Parkway S.E.

Irvine Suite# D/E

CA 92618 Smyrna GA 30080

TOLL FREE NUMBER: 1-877-886-5989

Nanjing PRO-COM Electric Appliance Co.,Ltd.

#6 Chuangye Road,High New Tech.Zone,

Great Bridge Road North,Nanjing,210061,China.

PR-MCL051-01-0506

Summary of content (28 pages)

PAGE 1
INFRARED VE N T-F RE E NATURAL GA S SPACE H E AT E R OW NE R ’ S OPE RAT ION AND INSTA LLATION M ANUAL WARNING : If th e i nformati on in this manual is not followed exactly, a fi r e o r exp l o si o n may resu l t causing property damage, personal injury, or loss of life. Do not store, or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
PAGE 2
Table of Contents Safety Information......................................................................................2 . . Product Features..................................................................................... 3 . . Local Codes..............................................................................................3 . . Unpacking................................................................................................. 4 Air for Combustion and Ventilation......................
PAGE 3
SAFETY INFORMATION WARNING: Do not use any accessory not approved for use with this heater. WARNING: Any change to this heater or be dangerous. its controls can 3. WARNING Modles MN 200EPC MN200EHPC MN300EPC MN300EHPC are equipped for natural gas. Field conversion is not permitted. 4. Due to high temperatures, heater should be kept out of traffic and away from furniture and draperies. Front surface of heater becomes very hot when running heater.
PAGE 4
PRODUCT FEATURES ON/OFF Switch Touch Pad Cabinet Top Burners Grill Guard Ignitor for Manual Override Control System Lower Front Panel Door Safety Pilot Control Knob for Manual Override Control System Figure1 Vent-Free Heater State of Massachusetts : The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts. Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a copy of 527 CMR30 upon sale of the unit.
PAGE 5
AIR FOR COMBUSTION AND VENTILATION WARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home. PROVIDING ADEQUATE VENTILATION The following are excerpts from National Fuel Gas Code. NFPA 54/ANSI Z223.1, Section 5.3. Air for Combustion and Ventilation.
PAGE 6
3. Add the Btu/Hr of all fuel burning appliances in the space. Btu/Hr Vent-free heater Gas water heater* Btu/Hr Example: Gas furnace Btu/Hr Gas water heater 40,000 Btu/Hr Vented gas heater Btu/Hr Vent free heater + 18,000 Btu/Hr Gas Fireplace logs Btu/Hr Total = 58,000 Btu/Hr Other gas appliances* + Btu/Hr Total = Btu/Hr *Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors. 4.
PAGE 7
INSTALLATION NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.
PAGE 8
3. INSTALLATION Attaching to Wall Anchor: This m et ho d allow s you to att ac h mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry). Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket. Marking Screw Locations 1. Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level. WARNING: Maintain minimum clearances shown in Figure 6.
PAGE 9
INSTALLATION CONNECTING TO GAS CONTINUED SUPPLY Installing Bottom Bracket (See Figure 10) 1. Install bottom bracket to heater bottom with two screws. It may be more convienent to remove heater from wall mounting bracket to attach bottom bracket. 2. Place heater on mounting bracket. 3. Locate two bottom mounting holes on wall. These holes are near bottom on heater. WARNING: A qualified service person must connect heater to gas supply. Follow all local codes.
PAGE 10
INSTALLATION Pressure Testing Gas Supply Piping System Test Pressures In Excess Of 1/2 PSIG (3.5 K Pa) Figure 12 -Gas Connection *A CSA/AGA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA/AGA design-certified equipment shutoff valve from your dealer. State of Massachusetts : The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts.
PAGE 11
CHECKING GAS CONNECTIONS CONTINUED Pressure Testing Heater Gas Connections . A This appliance is equipped with 4. Wait five (5) minutes to clear out any an ignition device which automatically lights the pilot. Do not try to light the pilot by hand. gas. Then smell for gas, including B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor .
PAGE 12
OPERATING YOUR HEATER continued TO TURN OFF GAS TO HEATER SETTING TIMER 1.Press the IGN/OFF button on the AUTO ON: With burner off, press touch pad. TIMER button. Then press or to 2.Set the ON/OFF switch to OFF position on top panel. press the TIMER button again, the NOTE: Wait one minute to light will flash. Burner will automatically come on at the set time. AUTO OFF: With burner operating, or again after shutting off heater.
PAGE 13
MANUAL OPERATING INSTRUCTIONS MANUAL LIGHTING PROCEDURE (Match Light) continued 9. When electric power is available and electronic operation is desired, turn clockwise 1. Remove lower front panel. to under Manual Operatting OFF position for one minute. Then press down knob and rotate clockwise Figure 16 - Correct Pilot Flame Pattern 2. Follow steps 1 through 5 Instructions on page 12. 3. to ELECTRIC strike match. Hold match position. Do not operate between locked positions.
PAGE 14
CLEANING AND MAINTENANCE WARNING: Disconnect take out the control module. W hen To clean these parts we recommend installing , reverse the steps above. using compressed air no greater (See Figures 20, 23 and 24) than 30 PSl. Your local computer store, hardware store, or home center power before attempting any may carry compressed air in a can. maintenance or cleaning to reduce You can use a vacuum cleaner in the the risk of fire , electric shock or blow position.
PAGE 15
Figure 23(Model MN300EPC) Figure 24- Double Control System Diagram (Model MN200EHPC MN300EHPC) 15
PAGE 16
FLOOR MOUNTING STAND PARTS NOT UNDER WARRANTY REPLACEMENT PARTS Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty. Contact authorized dealers of this product. If they can’t supply original replacement part(s), call PRO-COM’s For locating heater on the floor, away from a wall. Complete installation instructions provided with floor mounting base stand. phone number (877)886-5989.
PAGE 17
TROUBLESHOOTING WARNING: If you smell gas l l l l Shut off gas supply. l If you cannot reach your gas supplier, call the fire department. Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Immediately cal l your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. IMPORTANT: Operating heater where impurities in air exist may create odors.
PAGE 18
TROUBLESHOOTING Continued POSSIBLE CAUSE OBSERVED PROBLEM ODS/pilot has flame, but burner(s) does not light 1. Burner injector is clogged 2. Inlet gas pressure is too low 3. Thermocouple leads disconnected or improperly connected 4. Batteries weak Delayed ignition of burner(s) 1. Manifold pressure is too low. 2. Burner injector is clogged Burner backfiring during combustion 1. Burner injector is clogged or damaged 2. Burner is damaged. 3. Excessive supply pressure damaged regulator REMEDY 1.
PAGE 19
TROUBLESHOOTING Continued OBSERVED PROBLEM Heater produces unwanted odors Heater shuts off in use (ODS operates) POSSIBLE CAUSE REMEDY 1. Heater is burning vapors from 1. paint, hair spray, glues, etc. (See IMPORTANT statement at beginning of troubleshooting) 2. Gas leak. See WARNING 2. Statement at beginning of troubleshooting 1. Not enough fresh air is available. 1. 2. Low line pressure 2. 3. ODS/pilot is partially clogged 3. Gas odor exists even when heater is 1. Gas leak.
PAGE 20
ILLUSTRATED PARTS BREAKDOWN MN200EPC 20
PAGE 21
PARTS LIST MN200EPC This list contains replaceable parts for your heater. W hen ordering replacement parts, following the instructions listed under Replacement Part on page 15 of this manual. DESCRIPTION KEY NO. ML170EPC 1 2 3 4 5 6 7 7-1 7-2 8 9 10 11 12 13 14 15 16 MCL001-02 MCL008-01 VL067-01 NAM02-00 MCB19003 NAY03-05-01 PART NO.
PAGE 22
ILLUSTRATED PARTS BREAKDOWN MN200EHPC 22
PAGE 23
PARTS LIST MN200EHPC KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16-1 16-2 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 This list contains replaceable parts for your heater. W hen ordering replacement parts, following the instructions listed under Replacement Part on page 15 of this manual. MN200EHPC PART NO.
PAGE 24
ILLUSTRATED PARTS BREAKDOWN MN300EPC 24
PAGE 25
PARTS LIST MN300EPC KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16-1 16-2 17 18 19 20 21 22 23 24 25 26 27 28 29 30 This list contains replaceable parts for your heater. W hen ordering replacement parts, following the instructions listed under Replacement Part on page 15 of this manual. MN300EHPC PART NO.
PAGE 26
ILLUSTRATED PARTS BREAKDOWN MN300EHPC 26
PAGE 27
PARTS LIST MN300EHPC KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16-1 16-2 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 This list contains replaceable parts for your heater. W hen ordering replacement parts, following the instructions listed under Replacement Part on page 15 of this manual. MN300EHPC PART NO.
PAGE 28