Operating instructions

ManualsBrandsProCom ManualsHeating, Ventilation, and Air Conditioning29 in. Vent-Free Dual Fuel Firebox Insert

Before beginnig assembly of product, make sure all parts are present. Compare

parts with package contents list and diagram under. If any part is missing or

damaged, do not attempt to assemble, install or operate the product. Contact

customer service for replacement parts.

Estimated Assembly Time: 30 minutes.

Tool List For Assembly (Not Included):

KEY NO DESCRIPTION QUANTITY

1 PHILLIPS SCREWDRIVER 1

2 WIRE CUTTING PLIERS 1

Part List

KEY NO PART NUMBER

DESCRIPTION QUANTITY

1 XB001-01 Power Cord 1

2 XB002-01F Blower 1

3 XB003-01 Temperature Sensor 1

4 XB004-01F Connect Wire 1

5 PF06-0400-A Rocker Switch 1

6 M4.2×8 Screw 6

7 4.0×8 Screw 1

8 VL057-03 Cable Tie 6

IMPORTANT: Read all instructions and warnings carefully before starting installation.

Failure to follow these instructions may result in a possible electric shock, fire hazard

and will void the warranty.

Question, problems, missing parts? Before returning to your retailer, call our customer service

department at 1-877-866-5989 in English.

PACKAGE CONTENTS

Blower for the FBD28 series

& FBD32 series Fireplace

systems

FAN

0901

Summary of content (10 pages)

PAGE 1
Blower for the FBD28 series & FBD32 series Fireplace systems PACKAGE CONTENTS Before beginnig assembly of product, make sure all parts are present. Compare parts with package contents list and diagram under. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts. Estimated Assembly Time: 30 minutes.
PAGE 2
Safety Information 1. Read all instructions before using this appliance. 2. If possible always unplug this appliance when not in use. 3. Do not operate any heater with a damaged cord or plug or after the appliance malfunctions, has been dropped or damaged in any manner. 4. Any repairs to this appliance should be carried out by a qualified service person. 5. Under no circumstances should this appliance be modified.
PAGE 3
Exploded Drawing 3 1 2 5 4 6 8 7 3
PAGE 4
Assembly Procedure for Item FBD28 Series Optional Parts: NOTICE: Shut off gas heater during the following blower installation. Figure 1 Remove upper fire box by Figure 2 Unscrew two screws on Figure 3 Fix temperature sensor to unscrewing left/right screws on the heat insulation board cover and heat insulation board cover as fire box. draw it out. shown in the figure. .
PAGE 5
Figure 10 Fix the grounding. Figure 11 Insert the blower. Figure 12 Connect the port and shell board with linker (male port) into the three wires preset aside screws (please refer to linker (female port) preset (red, yellow and black) with grounding label); add gasket aside. switch separately. Codes between shell board and on wires must correspond grounding port with those on the rocke Figure 13 Push the rocker switch into Figure 14 Insert the male port, which the hole on the panel.
PAGE 6
Assembly Procedure for Item FBD32 Series Optional Parts: NOTICE: Shut off gas heater during the following blower installation. Figure 1 Remove upper fire box by Figure 2 Unscrew two screws on Figure 3 Fix temperature sensor to unscrewing left/right screws on the heat insulation board cover and heat insulation board cover as fire box. draw it out. shown in the figure. .
PAGE 7
Figure 10 Fix the wires, which is Figure 11 Fix the grounding. Figure 12 Insert the blower. matched with metal wafer, to the shell with three screws. Figure 13 Connect the port and shell Figure 14 Push the rocker switch Figure 15 Insert the male port, which board with linker (male port) into the into the hole on the panel.
PAGE 8
Electrical Connection A 15 amp, 120 Volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. Plan the installation to avoid the use of an extension cord. Extension cords are for temporary use only.
PAGE 9
Operating Instructions Using Rocker Switch, turn blower on and check for operation. Turn on Rocker Switch to the desired position. In the MAN position it will remain constantly on. AUTO position will be controlled by the Temperature Sensor. To stop the operation turn Rocker Switch to the OFF position. Electrical Wiring Diagram Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes.
PAGE 10
Maintenance of Motors Always disconnect the appliance from the main power supply and allow it to cool before any servicing operation. The motors used on the fan heater and flame blower are pre-lubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the appliance around the air intake and exhaust, as well as the fan heater is recommended. For heavy or continuous use, periodic cleaning must be done more frequently.