Specifications

6
N° TYPE OF FUNCTION BUTTON A BUTTON B FACTORY SETTING
selection A selection B standard configuration
(flashing led) (led off)
1 buzzer yes no no
2 control of horn/siren continuous alternating alternating
3 safety lock yes no no
4 sensibility of volume protection standard reduced standard
5 current drop sensor yes no no
6 short timing for central door locking 0,5 sec function 7 0,5 sec
7 long timing for central door locking 1,5 sec 4,5 sec 1,5 sec
8 comfort closing yes-manual no no
9 automatic comfort yes no no
10 dead lock yes no no
11 control of electric windows automatic manual manual
12 panic alarm yes no no
13 test of peripheral alarms yes no yes
14 intentional anti carjacking function yes no no
15 automatic anti carjacking function 1 yes no no
16 automatic anti carjacking function 2 yes no no
17 not used -- -- --
18 siren supplied SC1 M02 according to kit
19 Key 4 keypad yes no no
20 control of safety locking brake pedal mileometer mileometer
21 distraction-proof rearming yes no no
22 function of remote control buttonss factory setting custom setting factory setting
23 passive arming with alarm functions yes no no
24 passive arming of immobiliser yes no no
25 peripheral alarms active derived continuous derived
1 alarm only
CUSTOMISING THE OPERATING FUNCTIONS
The installed alarm system has a series of preset factory settings, which can be modified according according to the vehicle
that the alarm system is to be installed on as well as the owner’s preferences.
The factory settings and their possible customisations are illustrated in the table below.
Proceed as follows to modify the factory setting:
- arm the alarm system with the remote control;
- turn the ignition key to its ON position in order to switch the vehicle’s dashboard on;
- press button A on the remote control 4 times (fig. 1): the direction indicators will flash each time the button is pressed;
- after the button is pressed for the fourth time, the siren will make a series of signals (M02=4 BOOPS - SC1=4 BIP- BIPS) to
confirm that you have accessed the programming mode for the operating functions: the LED flashes quickly
N.B. you can only modify one function at a time.
- Press the button on the SWITCH/LED module installed on the dashboard or press button 1 on the keypad, if present, for the
same number of times as the function you want to set (the direction indicators flash to confirm each time you press the button
and go from one function to the next): if the LED flashes slowly the setting of the function is the “A selection” type, if it remains
off the setting is the “B selection” type;
The Led flashes quickly to indicate that a ‘not used’ function has been selected
- to change the setting, press
• button A on the remote control if you want the setting as per “A selection”: the siren makes one BEEP sound to
confirm this, or press
• button B on the remote control if you want the setting as per “B selection”: the M02 siren makes one BOOP sound
to confirm this; if you have installed a SC1 siren, this will make 2 BIP sounds;
- to change the setting of another function, repeat the 2 previous steps within 20 seconds;
- to exit the operating functions customisation phase, turn the ignition key back off and switch the vehicle’s dashboard off, then
disarm the system by pressing button A on the remote control.
N.B. During selection of a function, if you press the button on the SWITCH/LED or button 1 on the keypad, if present, for a
number of times that corresponds to a function which is not used or one that does not exist, you will hear 4 BOOPS of the M02
siren or 8 BIPS of the SC1 siren when you press the button on the remote control, and the LED will flash quickly to indicate
the anomaly.
CHECKING THE SETTING OF THE OPERATING FUNCTIONS
When customising the operating functions, you can check the status of each individual setting. The LED will indicate the current
setting after you have pressed the button on the SWITCH/LED or button 1 on the keypad, if present, the same number of times
as the function you want to check, as follows:
- slow flashing = “A selection” type setting
- off = “B selection” type setting