Specifications

15
BUTTON B
BUTTON A
TX mykro
M252
ISTRUCTIONS FOR USE MAIN CONTROLS AND SIGNALS (* configuration must be made)
ALARM: 25 sec. cycle can be stopped by remote control * PASSIVE ARMING OF ENGINE IMMOBILISER: arms 4 minutes after the engine is turned off, or 50 sec. after a door is opened (with engine off). * PASSIVE ARMING OF ALARM + IMMOBILISER: arms 60 sec. after opening and closing a door (with engine off). PRE-ALARM: only if passive arming of alarm has been enabled or if armed by electronic key. An alarm cycle is produced after 5 sec.
FINCTIONS
INDICATORS
FLASHING
1 FLASH
2 FLASHES
SIREN
SOUNDING
Series of
BEEPS
for 5 sec.
LED
OFF
Flashing very
slowly
Flashing very slowly
during first 25 sec.
(initial immunity time)
Same as previous
status
ADDITIONAL SIGNALS (*configuration must be made)
FUNCTIONS
FACTORY SETTING
*CUSTOM SETTING
INDICATORS
SIREN
LED
ARMING: with manual and automatic comfort closing of electric windows if selected by installer.. DISARMING: if you don’t get inside the car within 2 minutes when the distraction-proof function has been enabled, the system will completely rearm. The system is completely disarmed during an alarm. EXCLUSION OF ULTRASONIC VOLUME PROTECTION AND AUXILIARY MODULES: press within 25 sec. of arming. STOP ALARM CYCLE: without disarming the system *PANIC: can be activated when control unit is armed, after initial immunity time, max duration 10 sec., can be interrupted by pressing same button
BUTTON A
BUTTON A
BUTTON B
1st press US
2nd press
auxiliary modules
BUTTON B
BUTTON B
can also be
activated when
control unit is
disarmed
BUTTON B
BUTTON A
1st press US
2nd press
auxiliary modules
2 FLASHES
1 FLASH
3 FLASHES EACH
TIME BUTTON IS
PRESSED
FLASHING
STOPS
FLASHING
2 BEEPS (if buzzer ON*)
If peripheral protection is active:
M02= 1 BOOP, SC1= 2 BIPS
1 BEEP (if buzzer ON*) and no alarms
were triggered. If alarms were triggered
(after the BEEP if buzzer ON* ):
M02= 1 BOOP, SC1= 2 BIPS
1 BEEP + 4 rapid BEEPS
if car battery is flat and buzzer ON*
3 BEEPS each time
button is pressed
(if buzzer ON*)
SUONDING STOPS
SOUNDING
FLASHING: turns off briefly
during first 25 sec. (initial
immunity time),
then flashes slowly
Turns off if no alarms were
triggered, otherwise
flashes to signal memorised
alarms (see relative table)
FLASHING: rapidly during first
25 sec. (initial immunity time)
then flashes slowly
FLASHING:
Flashes slowly
Same as previous
status
BUTTON A BUTTON A
BUTTON A
BUTTON A
BUTTON B
GARAGE FUNCTION Enables the passive arming of the engine immobiliser, passive arming of alarm, distraction-proof re-arming and anti-carjacking functions to be temporarily neutralised. If the garage function is enabled, the engine can be turned on 15 times and remains memorised even if the alarm control unit’s power supply is disconnected. When the ignition key is ON (instrument panel ON) the LED will flash to indicate that the garage function has been selected. Use of remote control will cancel this setting. LED/SWITCH: press button A on the remote control and the button on the LED, the direction indicators will flash once, the M02 siren will produce 1 BOOP sound whilst the SC1 siren will produce 2 BIP sounds. KEY4 Keypad: press 2 buttons on the keypad at the same time and press button A on the remote control to transmit a signal: the keypad will produce 4 BEEPs to confirm reception. Release the 2 buttons and key in the override code within 10 sec: the direction indicators flash 2 times and the siren produces 2 BEEPs to confirm the function has been activated.