WATER / SEMI TRASH PUMP OWNER'S MANUAL Model WP255 IMS (International Merchandising Warranty Services) Information Do Not Return To Store One year Products Service To identify is available a provider Limited ManufactureCs are not to be returned from a network to retailer of providers in your area or for warranty 866 797 2738 Warranty.
CONTENTS ( I ) SAFETY INFORMATIONS .................................... 2 (If) SAFETY LABEL LOCATION-S.............................. 2 (lli) NAMEOF EVERY PART .................................... 3 (IV) PRE STARTING OPERATION-.............................. ,t (V) STARTING THE ENGINE.................................... 7 (V[) IJSING METHODOF WATERPIJMP ........................ 9 (\ll) STOPPIN(; THE ENGINE.................................... 10 (VIII) PERIODIC MAINTENANCE..................
( I ) SAFETY INFORNATIONS •To sure safety, caustic, brine(e.g, caustic liquid(e.g, don' t use wine, water gasoline oil and been •To prevent fire, clean tt_e overflowing fuel. • To prevent conditions. fire, never use the in machine in a place children are not likely being poisoned exhausting, never point being poisoned, exhaust indoors or • To avoid any where accident, horizontal and • To avoid where and flammable pedestrians the or machine.
Should one become dealer for its detached o1" unreadable, (III) NAMEOF EVERYPART contact replacement.
(IV) 1: PRE-STARTING OPERATION Connect Used intake pipe conmlercially connecting can hoop. not best be it pump length of far as shown intake which may and does from the water. The time that in direct proportion The must filter be to which fixed on the forms the end the fired on the picture. the filter The result continuous be pump the pipe. pipe the pipe.
Note: Fix the pipe connecting hoop well, in case the outlet pipe outlet pipe comes tll]crowl]ed ul]der the high pressure. 3: Check pipe connecting oil lever oil is hoop Caut ion: SEngine the function and one of the the using main factors life of the which influence generator. Do not recommend to use dirty engine oil. Qcheck the oil lever when the generator stops and make sure theft the generator in the horizontal position.
4: Check tile fuel levelRemove the fuel tank cap andcheck tile fuel level. If the fuel. fuel is low, please add Never use all oil gasoline mixture or dirty gasoline. Avoid getting dirt, dust or water illtile fuel tank. 5: Check tile air cleaner cushion and air cleaner elementsRemove tile cover. Check tileair element for dirt or obstruction, clean the air cleaner element, if it is dirty(see page 14) Caut ion: screw, cleaner aircleancover Never run tile engine without tile _ir cleaner.
(V) STARTING THE ENGINE 1: Turn the fuel 2: Turn off the Note cock chock lever to "ON". rod. : If the to start position choke the as lever has engine, the been moved gradually engine warms to move the it CLOSED to up. choke rod close ...... .....
4:Move the tension tension 5: Pull then it Warning : Do not allow engine. starter. Return to the left. rod slowly pull rod on the recoil starter until it is ngaged, briskly.
(VI) USING METHODOF WATERPUMP 1: After choke engine to rod rtlnnlng miltt_tes, some choke 2: Turn water up the When it to keep the ft_el ,i. After drain rod tension rod properly so the pump sucks quickly rod 3: the tile open to 1)ump body tension ttlrn position. "ON" ...... please is on stable machine at running, proper adjust rotate the speed tension to rod decrease constanption. using the water the puml) , in remove 1)tanl) body.
(VII) STOPPING THE ENGI_ 1: Remove 2: Turn the the tention engine rod to switch the to right. "OFF" position. engine switch _,close high 3: Turn the fuel low cock lever to "OFF" fuel valve close 10 position.
(VII) PERIODIC MAINTENANCE Periodic inspection and adjustment of petrol engine/water-pump are essential if high level performance is to be maintained. Regular maintenance will also help to extend service life.
1: Engine oil change Drain the the oil engine warm to rapid while is still 0evo j assure and complete draining. A: filler Remove filler the cap engine Install C: refill the and toward B: with oil drain plug the oil oil container filler by tipping the neck. oil drain plug the reeonmend and screw oil(see in. page 6) and check level. ENGINE Wash drain the the oil cap oil OIL your CAPACITY: hands O.
Warning: Never use leaning could Caut gasoline the or air low cleaner point flash element, i solevents fire or for explosion result. ion: Never run engine the wear A: Remove cleaner engine will the cover air cleaner. Rapid result. and the elenlent. B: Wash the element a nonflanmmble point the air air cleaner flash without in or high solvent k. m_d dry it thoroughly. C: Sock the the element excess in clean engine oil and squeeze out oil.
Clean the spark plug with a wire brush if it is to be reused. O. 70-0. 80mm O. 028-0. C: Measure Correct the as plug gap necessary with by 031in a feeler carefully gauge. bending the side electrode. The D: gap should Check and that thread the be O. 70 the spark spark O. 80nml plug plug washer in by is hand in to good condition prevent cross threading.
(IX) TRANSPORT/STORAGE Warning : OTo prevent burning oi"fire, cool tilemachine before transport or in store room. SWhile transport tilemachine, make sure the fuel valve in the "OFF" position, and place it in the horizontal in order to prevent gasoline spill out, spilled fuel or fuel vapor may ignite. Before store tilewater pump for a long time: i: clean tileinside of water pump......
several revolutions reinstall the 6: pull 7: Cover the the spark starter water to distribute the oil, then plu_. _rip slowly pump to keep 16 until out resistance dust. is felt.
(X) TROUBLESHOOTING Engine won't start 1: Is there fuel in the fuel tank? 2:Is the fuel valve in the "on" position? 3: Is gasoline reaching the carburetor? 4: Is the engine switch in the ON position? 5: Is there oil in the crankcase? 6: Is there a spark at spark plug? A: Remove the spark plug cap. Clean any dirt from around the spark plug base, then remove the spark plug. B: Install the spark plug in the plug cap. C: Turn the engine switch ON.
\ 18
(XI) SPECIFICATION Model 6101W Overall Length 490mm Overall Width 380nnn Overall Height 390mm Dry Weight 26Kg ENGINE Type 4- Stroke,Overhead Bore X Stroke Output Noise valve, 1cylinder 68 X 45mm Rate Power 4.1Kwi3600rpm Max. Torque 11N.mi2500rpm Cooling system Ignition system shaft rotate lever(side Force air TCI direction Against clock (from of muffler) output 82dBA WATER PUMP Intake pipe diameter 50mm(2.0in) Outlet pipe diameter 50mm(2.0in) Rotate speed Max.
20
