Use and Care Manual

ManualsBrandsPRO-SERIES ManualsBuilding materials3-Story Rolling Scaffold Tower with 1000 lbs. Load Capacity

ITME # TOWERINT3

Scaffold Tower Assembly & Operating Instructions

READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.

This manual provides important information on proper operation and maintenance. Every effort has been

made to ensure the accuracy of this manual. We reserve the right to change this product at any time

without prior notice.

Questions? Problems? CALL CUSTOMER SERVICE.

If you experience a problem or need parts for this product, call our customer help line at 1-636-532-9888,

Monday-Friday, 8 AM - 4 PM Central Time. A copy of the sales receipt is required.

NOTE: This scaffold can be used indoors, and can be used outdoors on flat surfaces. It should not be stored

outdoors, as the wood platform is not water resistant. This item is not compatible with stem jacks.

Summary of content (11 pages)

PAGE 1
ITME # TOWERINT3 Scaffold Tower Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation and maintenance. Every effort has been made to ensure the accuracy of this manual. We reserve the right to change this product at any time without prior notice. Q uestions? Problem s? CALL CU STO M ER SERVICE .
PAGE 2
TOWERINT3 Scaffold Tower Assembly and Operating Instructions WARNING: Improper erection, dismantling or use of Multi-Use Scaffold may result in serious injury or death! Erectors, dismantlers, and users of Multi-Use Scaffold must read and fully understand these Safety Rules and Instructions.
PAGE 3
STEP 1 Attach side brace B to two frames A: • Pull L-shape lock pin at each end of side brace to the disengaged position. (See Figure B) • While holding L-shape pin in disengaged position, place U-channel on each end of side brace B around leg of frame A at desired platform height. • Release lock pin and be sure that pin fully engages into hole in frame A leg • Install Connector Pins F under Lock Pin on all four sides.
PAGE 4
WARNING: • RECHECK ALL SIDE BRACE LOCK PINS FOR FULL ENGAGEMENT BEFORE ACCESSING PLATFORM. • RECHECK PLATFORM TO BE SURE IT IS PROPERLY SEATED WITHIN SIDE BRACE CHANNEL AND THE PLATFORM CLIPS ARE FULLY ENGAGED BEFORE ACCESSING. • WHEN ACCESSING PLATFORM, CLIMB OVER TOP OF FRAME LADDER – DO NOT SWING AROUND SIDE OF FRAME. • REMOVE THE PLATFORM BEFORE ADJUSTING THE DECK LEVEL.
PAGE 5
SCAFFOLDING SAFETY RULES SERIOUS INJURY OR DEATH MAY RESULT FROM IMPROPER ERECTION OR USE of scaffolding equipment. Erectors and users must be familiar with and follow safe practice and the Safety Rules contained herein. These Safety Rules cover generalized situations only and should not be used to replace any other additional safety and precautionary measures that may be necessary to cover the many usual or unusual conditions encountered during installation or dismantling.
PAGE 6
K. TIEING THE SCAFFOLD TO THE STRUCTURE IS OF GREAT IMPORTANCE to the stability and safety of the scaffold. Assure that the structure to which the scaffold is tied or anchored is capable of safely supporting all loads imposed by the scaffold. L. FREE STANDING SCAFFOLDS other than wall scaffolds must be restrained from tipping by guying or other means, recognizing that stability is essential to the safety of the scaffold. M.
PAGE 7
ASSEMBLE THREE SCAFFOLD UNITS TO BUILD ONE SCAFFOLD TOWER (A) 1-Piece Guard Rail System Set For interior or exterior use. Includes hinged doors, steel frame, durable powder coat paint finish. Assembled size: 69 inch L x 39 inch H x 29 inch W (B) 3-Pieces 6 Foot Multi-Use Scaffold Unit (C) 4-Pieces Adjustable Outriggers For interior or exterior use. Steel frame, powder coat paint finish. Extends the width of the base so that units can be stacked.
PAGE 8
Recommended Scaffolding Erection Procedure Introduction This Guide has been prepared by the Scaffolding, Shoring & Forming Institute to assist contractors, architects, engineers, dealers, erectors, and users, etc. for the proper use of scaffolding equipment. Scaffolding Safety Rules published by the Institute should be used in conjunction with this publication, as well as the instruction for the use of scaffolding provided by the manufacturer.
PAGE 9
3. Welds- Equipment should be checked before use for damage of welds and any piece of equipment showing damaged welds or rewelding beyond the original factory welds should not be used. The factory weld reference pertains to location and quality of welds. While corrosion, straightness of members, and welds are of primary concern other component parts should be checked. 4. Locking devices on frames and braces shall be in good working order, and if not, must be repaired or replaced prior to use. 5.
PAGE 10
wind and weather. The scaffolding components to which the ties are attached must also be checked for additional loads. When erecting additional lifts, always work from planking within the scaffold structure. Move planking as erection progresses. Planking and Accessories Use only lumber that is properly inspected and graded for use as scaffold plank. Planking shall have at least 12” of overlap and extend 6” beyond center of support or be cleated at both ends to prevent sliding off support.
PAGE 11
2. Dismantle scaffold from the top down. Begin by removing all accessories from that lift being dismantled at the time. 3. Always work from a minimum of two planks placed on the tier of frames below those being removed. Move the planking down as dismantling progresses. 4. Do not remove ties until dismantling has reached the tier to which they are attached. 5. Always stay within the inside of the scaffold. Do not climb on the outside for any reason when dismantling.