User's Manual

ManualsBrandsPro-Nets Technology ManualsElectronicsWIRELESS 11n ROUTER

high traffic flows along in the wireless network. If the 802.11g MIMO Wireless Router often

transmit large files in wireless network, you can enter new Fragment Threshold value to split

the packet. The value can be set from 256 to 2346. The default value is 2346.

RTS Threshold: RTS stands for “Request to Send”. This parameter controls what size data

packet the low level RF protocol issues to an RTS packet. RTS Threshold is a mechanism

implemented to prevent the “Hidden Node” problem. If the “Hidden Node” problem is an issue,

please specify the packet size. The RTS mechanism will be activated if the data size exceeds

the value you set. The default is 2347.

Tx Power: TX Power measurement.

Short Preamble: Select Disable or Enable this function, default setting is Disable. A preamble

is a signal used in wireless environment to synchronize the transmitting timing including

Synchronization and Start frame delimiter.

Short Slot: When short slot is Enable, the wireless device uses the short slot time only when

all clients associated to the 802.11g, 2.4-GHz radio supports short slot time. Short slot time is

an 802.11g-only feature and does not apply to 802.11a radios.

Tx Burst: Enable the transmitted time slot can increase transmission throughput.

Pkt_Aggregate: The parameter can be used to increase the delivered bandwidth in

community networks including fixed and mobile stations.

Country Code: Select your local Country code for pull-down menu. For Safety (FCC or CE

rule) reason, please don’t change this default setting.

WMM Capable: Enable/Disable the Wi-Fi Multimedia (WMM) support.

APSD Capable: Enable/Disable the APSD support.

WMM Parameters: Click “WMM Configuration” to setup the WMM function.

3.5.3 Security

This function allows you setup the wireless security. Setup the wireless security and

encryption to prevent from unauthorized access and monitoring.

Summary of content (10 pages)

PAGE 1
high traffic flows along in the wireless network. If the 802.11g MIMO Wireless Router often transmit large files in wireless network, you can enter new Fragment Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346. RTS Threshold: RTS stands for “Request to Send”. This parameter controls what size data packet the low level RF protocol issues to an RTS packet. RTS Threshold is a mechanism implemented to prevent the “Hidden Node” problem.
PAGE 2
SSID Choice: Select the SSID which you want to configure. Security Mode: This function allows you setup the wireless security. Enable security mode could prevent any unauthorized access to your wireless network. [Open: If your wireless router is using “Open” authentication, then the wireless adapter will need to set to the same authentication type. Shared: Shared key is when both the sender and the recipient share a secret key.
PAGE 3
standardized through 802.11i/WPA2 are: pre-authentication, which enables secure fast roaming without noticeable signal latency. RADIUS Server: RADIUS is an authentication, authorization and accounting client-server protocol. The client is a Network Access Server that desires to authenticate its links. The server is a server that has access to a user database with authentication information. IP Address: Enter the RADIUS Server’s IP address provided by your ISP.
PAGE 4
your wireless client earlier automatically connect to the Access Point. [WPS Summary] From this section, you can view the current WPS status, Configured, SSID, Auth mode, Encrypt Type, Default Key Index, WPS Key, and AP PIN information. Reset OOB: Click this button to rest the settings. [WPS Progress] WPS Mode: Specify the AP router acts as a Registrar or an Enrollee.
PAGE 5
3.5.5 Station list In this section, you can monitor stations which associated to this AP. 3.5.6 Site Survey Site Survey page shows information of AP nearby.
PAGE 6
3.6 Firewall The Firewall contains the following sections: ◎MAC/IP/Port Filtering ◎System Security Setting ◎Port Forwarding ◎DMZ ◎Content Filtering ◎Port Trigger 3.6.1 MAC/IP/Port Filtering Settings You can setup firewall rules to protect your network from virus, worm and malicious activity on the internet. Filters are used to deny or allow LAN computers from access the Internet.
PAGE 7
MAC Address: The MAC address of the computer in the LAN (Local Area Network) to be used in the MAC filter table. Enter the MAC address of LAN port, e.g. 00:00:27:88:81:18 Dest IP Address: The IP address that will be denied to access. Source IP Address: The IP address that will be denied access to the Internet. Protocol: This is the protocol type that will be used with the Port that will be blocked. Destination Port Range: The single port or port range that will be denied to access.
PAGE 8
3.6.2 Port Forwarding You may setup virtual servers to provide service on internet. Virtual Server Setting: Enable/Disable the port forward. IP Address: This is the port number on the WAN side that will be used to access the application. You may define a single port or a range of ports. You can use a comma to add multiple ports or port ranges. Port Range: This is the port used to forward the application. It can be either a single port or a range of ports.
PAGE 9
3.6.3 DMZ You may setup a De-Militarized Zone (DMZ) to separate internet network and internet. DMZ Setting: If the DMZ Host Function is enabled, it means that you set up DMZ host at a particular computer to be exposed to the Internet so that some applications/software, especially Internet/Online game can have two-way connections. Select Enable or Disable from the pull-down menu.
PAGE 10
3.6.4 System Security Settings You may configure the system firewall to protect AP/Router itself from attacking. Malformed Packet Detection: Filter the packet’s header unreasonable or unusual, such as IP, TCP, UDP, and ICMP protocols’ packet. IP Land Attack: When packet’s source IP and destination IP are same and the source port is also same as destination port, the packet is determined the IP Land attack and dropped by the router.