Instructions / Assembly

95512
ProGrid
®
CHECKERED MESH
HIGH BACK CHAIR
OPERATING INSTRUCTIONS
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs are
securely tightened.
3. Check that all bolts screws and knobs are tight every three
months or as needed..
4. Dispose of packing material properly. Do not use plastic cover
as head covering. It may cause suffocation.
5. Do not use chair as a stepladder.
6. Use this chair for its intended purpose only.
7. Use mild detergent only for cleaning.
PROLINE II LIMITED WARRANTY
ProLine II chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization.
At it’s option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component. The customer must prepay freight on any components returned to the factory. Return freight on components
still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs.
or less. The 54666 is for persons weighing 300 lbs. or less. The 39200, 39202, 39203, 81108, 81308 & 81608 are for persons weighing 400 lbs. or less.
This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a five
year warranty on all parts applies. Fabric is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
All ProLine II chairs meet or exceed ANSI BIFMA standards.
It is the customer’s responsibility to prepay freight on any components returned to the factory. Return freight on components covered by warranty
will be paid by Office Star Products.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax [phone], or toll free
parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
FEATURES
• SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1). To
lower seat height sit on chair and lift lever (1).
NOTE: It is normal for chair to slightly lower under body weight.
• SEAT & BACK ANGLE ADJUSTMENT
This chair is equipped with a mechanism that uses your own
body-weight to balance the force needed to recline the back and
ensure the tension is perfectly adjusted. To unlock, lean back
slightly and pull lever (2) up, leave lever (2) up for free float or
push lever (2) down to lock chair into position.
• ARM HEIGHT ADJUSTMENT
To adjust arm height, push button (3) in to allow the arms to
move up or down freely. Release the button (3) once the desired
height is reached.
• SLIDING ARM PAD ADJUSTMENT
To slide arm pads forward or backward, simply slide arm pad
into desired position.
2
1
3
© Office Star Products Novembre 2015
3
5
4
13
10
9
12
7
6
15
8L
14
1
11
2
8R
9
95512
FAUTEUIL À HAUT DOSSIER MAILLÉ
CARRELÉ ProGrid
®
INSTRUCTIONS DE MONTAGE
PIÈCE QTÉ
1. Base ..............................1
2. Roulette ............................5
3. Vérin Pneumatique ...................1
4. Soufflet ............................1
5. Mécanisme .........................1
6. Coussin du siège .....................1
7. Dossier ............................1
8. Bras (8L et 8R) ......................2
9. Bouton avec rondelles .................2
10. Vis du mécanisme ...................4
11. Vis avec rondelle ....................3
12. Vis pour le couvercle .................2
13. Vis du dossier ......................1
14. Couvercle en plastique ...............1
15. Support du dossier ..................1
16. Clé Allen (non montré) ................1
Le Tourne-a-vis de Phillips est aussi besoin pour
l’assemblage (non fourni)
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vous assurer que les quantités
des pièces sont correctes.
ÉTAPE 1 Insérer cinq roulettes (2) dans la base (1), les pousser très fort jusqu’à ce que vous entendiez ou sentiez la roulette (2) s’enclencher.
Insérer le vérin pneumatique (3) dans la base (1) et glisser les soufflets (4) sur le vérin pneumatique (3).
ÉTAPE 2 Fixer le mécanisme (5) au coussin du siège (6) avec la flèche vers l’avant de la chaise à l’aide de vis du mécanisme (10). SERREZ TOUTES LES
VIS AVEC LA CLÉ ALLEN (16)
ÉTAPE 3 Fixer les bras (8L et 8R) au coussin du siège (6) en utilisant un bouton avec des rondelles (9) pour chaque bras (8). RESSERRER
COMPLÈTEMENT TOUS LES BOUTONS AVEC DES RONDELLES (9).
ÉTAPE 4 Fixer le support du dossier (15) au dossier (7) avec vis du dossier (13). SERRER LA VIS À L’AIDE DE LA CLÉ ALLEN (16). Fixer le support du
dossier (15) à l’arrière du mécanisme (5) à l’aide du vis avec rondelles (11). SERREZ TOUTES LES VIS AVEC LA CLÉ ALLEN (16)
ÉTAPE 5 Placer le siège assemblé sur le vérin pneumatique (3) et mettre de la pression. Fixer le couvercle en plastique (14) sur le dossier (7) en utilisant les
vis pour le couvercle (12). RESSERRER COMPLÈTEMENT TOUS LES VIS.
ATTENTION : AVANT D’UTILISER LE FAUTEUIL, VOUS ASSURER D’AVOIR RESSERRÉ COMPLÈTEMENT TOUTES
LES VIS ET BOUTONS.