Owner's Manual

Replay at
78
r.p.m.
**
In
order
to
replay shellac
records at
78
r.p.m. your
turntable
must be equipped with the 78 r.p.m.
pulley
which
is
available
as
an optional
accessory
for
most models.
After fitting the
78
r.p.m. pulley please
proceed
as
follows:
Remove the
platter
and using the
tool
from the
accessory kit fit the
belt
around the
larger
diameter step
of
the
pulley. Replace
the Platter,
start the
turntable
at
33
r.p.m. and switch the speed
to
45
r.p.m., the
platter will then
revolve
at 78 r.p.m ..
Fitting the
78
r.p.m.
pulley
Before beginning work fit the cartridge's
needle
protection cover.
Remove the platter
and drive
belt. Please
remember that sweat
or
sticky fingers
will impair the function of the
belt.
Use
a piece
of
kitchen paper
or
a
cloth
to
remove the belt.
Measure the height of the
pulley
above the
plinth
in order
to
ease correct refitting.
Using a
small screwdriver
loosen
the grub screw in the neck
of
the
pulley
just
enough
to
remove the
pulley
vertically
without using force.
Refit
the
pulley
in the opposite order. Tighten the grub screw
carefully
making
sure you
do
not overtighten it.
Fit
the drive
belt
around the subplatter and the pulley. Again,
use
a piece
of
paper
or
cloth
to
avoid
soiling
the
belt. Replace
the platter.
**
78
r.p.m.
is
not available
with
the
Essential
(all
models), Xperience
Basic
+,
Xperience
Comfort,
Xperience
Aery/,
Xperience
Classic,
Xperience
SuperPack,
PerspeX,
PerspeX
Anniversary,
RPM
1 .3
Genie,
RPM
1.3
Genie
SuperPack,
RPM
9.
1,
RPM
9.
1
SuperPack,
RPM
9.1
Aery/,
RPM
9.2
Evolution,
RPM
10.
1
Evolution
and
Signature.
The
models Debut
111/Phono
SB,
Xpression
Ill
Comfort,
RPM
5
SuperPack,
RPM
5.
1
SuperPack,
RPM
6.
1
SB,
RPM
6.1
SB
SuperPack
and
Xtension
(all
models)
are
equipped
with
the
78
r.p.m.
pulley
as a
standard.
Technical specifications Pro-Ject
Speed
Box
S
Nominal speeds:
Quartz oscillator:
*
33
and
45
r.p.m.
**Optional
78
r.p.m.
Speed stability
+/-
0,001%
Turntable
connection:
l6V/AC
l90mA
max. (3W power consumption max.)
Outboard
power
supply: 18V
/500mA
DC,
suitable
for
your country's mains
supply
Dimensions W
x H x D
(D
with sockets): 1
03
x
36
x 1
04
(l
04)mm
Weight:
560g
without power supply
Service
Should you encounter a
problem
which you are not
able
to
alleviate
or
identify, please
contact your
dealer
for
further advice.
Only
when the
problem
cannot be resolved
there
should
the unit
be
sent
to
the responsible
distributor in your country.
Warranty
The
manufacturer accepts
no
responsibility
for
damage caused by not adhering
to
these
instructions
for
use.
Modification
or
change
to
any
part
of
the produd by unauthorized persons release the
manufacturer
from
any
liability
over
and above the
lawful
rights
of
the
customer.
Copyright, trademarks
PRO-JECT
is
a Registered Trademark
of
H. Lichtenegger.
This guide
was
produced by: Audio T rode
GmbH
Copyright©
2012.
All
rights reserved.
The
information
was
correct at the time
of
going
to
press.
The manufacturer reserves the right
to
make
changes
to
the
technical
specification without prior
notice
as
deemed necessary
to
uphold the ongoing
process
of
technical development.
©Audio
Trade
GmbH
·
Pro-Ject
Speed
Box
S ·
Revision
2012.11.1
3