Owner's Manual

Dear music lover,
thank you
for
purchasing a
PRO-JECT
AUDIO
Speed
Box.
*
The unit permits electronic speed change
of
your
Pro-Ject
record player between
33
and
45
r.p.m. and also permits the replay
of
shellac records
by
allowing
**
78
r.p.m. with an appropriate
pulley
and cartridge.
In
order
to
achieve maximum performance and reliability you should study these instructions
for
use
carefully.
V Warning
of
a
hazard
for
the
user,
the
unit
or
possible misuse.
~
Important
notice.
Safety
instructions
ViV
VI
AC
outlet voltages
vary
from
country
to
country. Before
connecting
to
the
mains,
make sure
that the
voltage
in
your
area
meets
the
voltage requirements printed
on
the
power supply.
The
power supply
is
used
to
disconnect
the
unit
from
the
mains.
Make
sure
that
the
power
supply
is
easily
accessible at
all
times.
Never handle
the
device,
the
power
supply
while
your
hands
are
wet
or
damp.
Avoid
letting
liquids
enter
the
device or the power supply. Never place any
item
containing
liquid,
such
as
a
flower
vase
on
or
near
the
device. Never
spill
any
liquid
on
the
device
or
the
power supply.
Never
place
any naked
flame
sources,
such
as
lighted
candles on
or
near
the
device.
The
product
shall
not
be
used
in
damp
or
wet locations,
next
to
a
bathtub,
sink,
swimming
pool
or
any
other
similar
conditions.
Connecting
the
record
player
Connect the power cable supplied (polarity
-
~
+)
to
the socket
Output
-16V
and
to
the power supply
socket
of
the record player. The original power supply
of
the record player
is
then no longer required.
~
VI
Make
all
connections
whilst
the
Speed
Box
is
disconnected
from
the power supply.
Only
models
with
mains socket power supply. 16V/190mAAC
max ..
*The
Pro-Ject
1.2
E,
Debut
Ill
E,
Debut
111/Phono
SB,
Debut Carbon
(all
models),
Xpression
Ill
Comfort,
Xperience
Comfort,
RPM
6.1
SB,
RPM
6.
1
SB
SuperPack,
RPM
9.1
SuperPack,
Xtension
(all
models) and Signature may not
be used
with
the Speed
Box.
Mains
power
connection
Connect the
low
voltage plug from the power supply
to
the socket Power
18V-
before connecting the power
supply
to
the mains.
V Never
use
any other power supply
than
the
one
supplied
with
the
unit.
To switch
on
from
standby
or
to
standby
The push button on the left hand side
will toggle the Speed Box between
its
fully
operational status and
standby.
The
blue
LED
above the stand-by
push
button shows that the unit
is
switched on.
Speed
selection
33/45
r.p.m.
><
.
....
·,·
.
•:•:
::
....
:
.·:·····
••
••
•••••••
i
•••••••
••••••••••
•••
•••••
••••
···:·•··
··:·-··
·n
••••••••••
......
.
..
.
.:
......
'•
.·
····
The belt must be on the
smaller (50Hz
models) larger
(60Hz
models) diameter part
of
the
motor
pulley.
Press
the button
33
45
to
switch between
33
and
45
r.p.m .. The selected speed
is
shown respectively
by
the
lit
LED.
To play at
45
or
**
78
r.p.m. please always start the turntable at
33
r.p.m. and then switch
to
the higher speed
when
it
has
attained full
speed.
2 ©Audio Trade GmbH
·
Pro-Ject Speed
Box
S ·
Revision
2012.11 .1