PRB08041 Recoil 2 26-inch - Manual

ManualsBrandsPro Boat ManualsBoatsRecoil 2 26" Self-Righting Brushless Deep-V RTR, Shreddy

Recoil 2

26 Self-Righting Deep-V Brushless RTR

56885 Sonicwake 36

Replacement Parts

Part # Description

HRZ00016 Horizon Pro Boat Receiver

HRZ00020 Horizon Multi Model LT Transmitter V2

PRB18039 Servo 5.3kg 4.826V Waterproof Analog

PRB281101 Hull and Canopy Heatwave: Recoil 2

PRB281102 Turn Fins and TrimTabs: Recoil 2

PRB281103 Rudder Assembly: Recoil 2

PRB281129 Hull and Canopy,Shreddy: Recoil 2

PRB282082 Flex Shaft: Recoil 2

PRB282084 Stuffing Tube: Recoil 2

PRB282085 Propeller, Aluminum: Recoil 2

PRB286075 Canopy Thumb Screws (4):Recoil 2

PRB286076 Water Cooling Lines:Recoil 2

PRB286077 Rudder Pushrod Set: Recoil 2

PRB286078 Hull Seal Set: Recoil 2

PRB286079 Compst Mount Straps: Recoil 2

PRB286080 Motor Mount: Recoil 2

PRB286081 Motor Coupler: Recoil 2

PRB286082 Propeller Strut Set: Recoil 2

SPMXME1A 100A Brushless Marine ESC 3S-4S

SPMXMM1200 Firma 2300Kv Brushless Outrunner Marine Motor

SPMX32003S30 3200mAh 3S 30C Smart LiPo Battery: IC3

Optional Parts

Part # Description

DYN4403 GPS Speed Meter 2.0

DYNE4200 Grease Gun w/ Marine Grease 5 oz

DYNM0102 Clear Flex Marine Tape (18M)

DYNT0502 Start Up Tool Set: Pro Boat

PRB282008 Propeller, Composite, 1.6 x 1.6 for 3/16 Shaft

SPM2340

DX3 Smart 3-Channel Transmitter with SR315

Receiver

SPMR5115 DX5C Smart 5-Channel DSMR Transmitter Only

SPMS605 S605 Analog Waterproof 9KG Surface Servo, 23T

SPMS612HV

S612HV Digital HV 12KG Waterproof Metal Gear

Servo

SPMS614 S614 Waterproof Metal Gear Surface Servo, 23T

SPMS614S S614S 15kg Steel Gear WP Servo, 23T

SPMSLT300

SLT3 3-Channel SLT Radio System with SR315

Dual Protocol

SPMSR315 SR315 DSMR 3-Channel Sport Receiver

SPMX32003S30 11.1V 3200mAh 3S 30C Smart LiPo Battery: IC3

SPMX32004S30 14.8V 3200mAh 4S 30C Smart LiPo Battery: IC3

SPMX324S100 14.8V 3200mAh 4S 100C Smart G2 LiPo Battery: IC3

SPMX324S50 14.8V 3200mAh 4S 50C Smart G2 LiPo Battery: IC3

SPMX40003S30 11.1V 4000mAh 3S 30C Smart LiPo Battery: IC3

SPMXBC100

XBC100 Smart LiPo Battery Checker & Servo

Driver

SPMXC1070 S150 AC/DC Smart Charger, 1x50W

SPMXC2040 S1400 G2 AC 1x400W Smart Charger

Binding is the process of programming

the receiver to recognize the GUID

(Globally Unique Identifier) code of a

single specific transmitter. The included

transmitter and receiver are bound at

the factory. If you need to rebind, fol-

low the instructions below:

1. Press and hold the AUX 3 button on the transmitter.

2. Power ON the transmitter.

3. Power ON the receiver. The receiver will flash to indicate auto-

matic binding.

4. Restart the transmitter by powering it OFF then back ON.

The LED remains steady, indicating binding is complete.

You must rebind when:

• You want different failsafe positions (e.g. when throttle or steering

reverse has been changed).

• Binding the receiver to a different transmitter.

NOTICE: Do not attempt to bind the transmitter and receiver if

there are other compatible transmitters in bind mode within 400

feet. Doing so may result in unexpected binding.

In the unlikely event that the radio connection is lost during use, the

receiver will drive the servo and ESC to their pre-programmed failsafe

positions (normally no throttle and straight steering).

If the receiver is powered on before powering on the transmitter, the

receiver will enter this failsafe mode. When the transmitter is pow-

ered on, normal control is resumed.

Failsafe

Binding

General Information